SIST EN 89:2001/A1:2001
(Amendment)Gas-fired storage water heaters for the production of domestic hot water
- BACK
- 31-Jan-2001
- 24-May-2015
- 91.140.65
- 2009/142/EC
- 2016/426
- 90/396/EEC
- M/BC/CEN/89/6
- PLN
Gas-fired storage water heaters for the production of domestic hot water
Gasbeheizte Vorrats-Wasserheizer für den sanitären Gebrauch
Appareils de production d'eau chaude par accumulation pour usages sanitaires utilisant les combustibles gazeux
Akumulacijski plinski grelniki za pripravo sanitarne tople vode - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 89:2001/A1:2001
01-februar-2001
Akumulacijski plinski grelniki za pripravo sanitarne tople vode - Dopolnilo A1
Gas-fired storage water heaters for the production of domestic hot water
Gasbeheizte Vorrats-Wasserheizer für den sanitären Gebrauch
Appareils de production d'eau chaude par accumulatio
...
This May Also Interest You
This document is applicable to gas-fired mCHP appliances producing domestic hot water and electricity. The electricity is generated in a process linked to the production of useful heat.
It applies to a mCHP appliances marketed as single unit or as a package fully specified by a manufacturer that have:
- a gas heat input not exceeding 400 kW,
- an electrical output not exceeding 50 kW, and
- a hot water storage capacity (if any) not exceeding 2 000 l.
EN 13203 1:2015 sets out in qualitative and quantitative terms the performance in delivery of domestic hot water for a variety of uses. It also gives a system for presenting the information to the user.
The present document sets out a method for assessing the energy performance of gas fired mCHP appliances. It defines a number of daily tapping cycles for each domestic hot water use, kitchen, shower, bath and a combination of these, together with corresponding test procedures, enabling the energy performances of different gas-fired appliances to be compared and matched to the needs of the user.
When the mCHP generator does not supply domestic hot water in the summer period, the present standard is not applicable. FprEN 13203 2:2018 is used for performance assessment of these generators.
- Standard26 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft26 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft25 pagesEnglish languagesale 10% offe-Library read for×1 day
- 01-Mar-2021
- 14-Nov-2022
- 91.140.65
- 2009/125/EC
- 2010/30/EU
- 811/2013
- 812/2013
- 813/2013
- 814/2013
- M/534
- PLN
Sorption heat pumps connected to or including a domestic hot water storage tank. It applies to a package marketed as single unit or fully specified that have:
— a heat input not exceeding 400 kW; and
— a hot water storage tank capacity (if any) not exceeding 2000 l.
In the case of combination boilers, with or without storage tank, domestic hot water production is integrated or coupled, the whole being marketed as a single unit.
EN 13203-1 sets out in qualitative and quantitative terms the performance in delivery of domestic hot water for a selected variety of uses. It also gives a system for presenting the information to the user. The present document sets out a method for assessing the energy performance of the appliances. It defines a number of daily load profiles for each domestic hot water use, kitchen, shower, bath and a combination of these, together with corresponding test procedures, enabling the energy performances of different gas-fired appliances to be compared and matched to the needs of the user. Where other technologies are combined with a gas-fired boiler or a water heater to produce domestic hot water, specific parts of EN 13203 apply.
Horizontal ground heat sources are not covered by the scope of the present European Standard.
- Standard32 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft29 pagesEnglish languagesale 10% offe-Library read for×1 day
This document is applicable to gas-fired appliances producing domestic hot water.
It applies to both instantaneous and storage tank appliances; waters-heaters and combination boilers that have:
— a heat input not exceeding 400 kW; and
— a hot water storage tank capacity (if any) not exceeding 2000 l.
In the case of combination boilers, with or without storage tank, domestic hot water production is integrated or coupled, the whole being marketed as a single unit.
The water heaters covered by the present standard are considered "conventional water heaters" as defined by the Transitional Methods (Commission Communication 2014/C 207/03) then in the calculation formula for the Annual Electricity Consumption (AEC), Qcor is equal to zero.
EN 13203-1 sets out in qualitative and quantitative terms the performance in delivery of domestic hot water for a selected variety of uses. It also gives a system for presenting the information to the user. The present document sets out a method for assessing the energy performance of the appliances. It defines a number of daily load profiles for each domestic hot water use, kitchen, shower, bath and a combination of these, together with corresponding test procedures, enabling the energy performances of different gas-fired appliances to be compared and matched to the needs of the user. Where other technologies are combined with a gas-fired boiler or a water heater to produce domestic hot water, specific parts of EN 13203 apply.
- Standard43 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft43 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard is applicable to gas-fired appliances producing domestic hot water. It applies to
condensing combination boilers with passive flue heat recovery device (PFHRD) that have:
— a heat input not exceeding 400 kW,
— a hot water storage tank capacity (if any) not exceeding 2000 l,
— a declared load profile between M to 4XL.
In the case of combination boilers, with or without storage tank, domestic hot water production is integrated
or coupled, the whole being marketed as a single unit.
For this standard, some tests and calculation results of FprEN 13203-2:2018 are used to calculate the energy consumptions.
- Standard26 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft21 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft17 pagesEnglish languagesale 10% offe-Library read for×1 day
This document is applicable to solar supported gas-fired appliances producing domestic hot water.
It applies to a system marketed as single unit or a fully specified system that:
- has a gas heat input not exceeding 70 kW; and
- has a hot water storage tank capacity not exceeding 500 l; and
- is equipped with at least one solar collector; and
- is, with regard to the solar hydraulic circuit, considered as a forced circulation system (definition according to EN ISO 9488:1999).
The appliances covered by this European Standard are described in Annex E (normative).
This document does not apply to thermo-siphon or integral collector storage tank systems according to definitions given by EN ISO 9488:1999.
NOTE In principle, the energy consumption of thermo-siphon solar preheat systems and integral collector storage tank preheat systems can also be assessed on the basis of this standard. One appropriate procedure for that purpose is to calculate the temperature level of the domestic hot water withdrawn from the thermal solar system for the reference conditions defined in this standard by using the numerical system model and the thermal solar system performance parameters according to ISO 9459-5. Based on the temperature level of the hot water withdrawn from the store the energy consumption of the gas appliance should be determined. This determination can either be done by means of calculations or by performing a test according to FprEN 13203-2:2020 and using instead of the cold water inlet temperature the hot water temperature withdrawn from the store.
This document is not intended to assess the performance:
- of the solar collector(s), which should comply with EN 12975-1:+A1:2010 and EN 12975-2:2006; and - thermal solar systems and components, which should comply with EN 12976-1:2017 and EN 12976- 2:2019.
Standard EN 13203-1:2015 sets out in qualitative and quantitative terms the performance in delivery of domestic hot water for a selected variety of uses. It also gives a presenting the information to the user. The present document sets out a method for assessing the energy performance of a solar supported appliance. It defines a number of daily tapping cycles for each domestic hot water use, kitchen, shower, bath and a combination of these, together with corresponding test procedures including information about the available solar radiation. It enables the energy performances of different gas-fired appliances to be compared and matched to the needs of the user.
- Standard22 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft22 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard is applicable to gas-fired mCHP appliances producing domestic hot water and electricity. The electricity is generated in a process linked to the production of useful heat. It applies to a mCHP appliances marketed as single unit or as a package fully specified by a manufacturer that have:
— a gas heat input not exceeding 400 kW;
— an electrical output not exceeding 50 kW and
— a hot water storage capacity (if any) not exceeding 2000 l.
prEN 13203-1:20xx sets out in qualitative and quantitative terms the performance in delivery of domestic hot water for a variety of uses. It also gives a system for presenting the information to the user.
The present document sets out a method for assessing the energy performance of gas fired mCHP appliances. It defines a number of daily tapping cycles for each domestic hot water use, kitchen, shower, bath and a combination of these, together with corresponding test procedures, enabling the energy performances of different gas-fired appliances to be compared and matched to the needs of the user.
When the mCHP generator does not supply domestic hot water in the summer period, the present standard is not applicable. PrEN 13203-2:2020 is used for performance assessment of these generators.
- Standard37 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft33 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard specifies a method for energy assessment of un-vented (closed) hot water storage tanks with a capacity up to 1 500 l, intended to be equipped with an external heat source and used for domestic hot water production. Whilst storage water heaters intended primarily for direct heating are not covered by this European Standard, it does allow the provision of electric heating elements for auxiliary use.
- Standard16 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard is composed of two parts.
The first part supplements EN 303 1, EN 303 2, EN 303 4 and EN 304 hereafter called boiler standards. It specifies the supplementary requirements and tests for the construction, safety, rational use of energy, fitness for purpose, classification and marking related to the domestic hot water operation of oil fired water heaters and combination boilers.
The domestic hot water is produced on either the instantaneous or storage principle. The domestic hot water production is integrated or coupled, the whole being marketed as a single unit.
The second part covers the energy performance of domestic hot water production of the appliances covered by the first part.
This second part sets out a method for assessing the energy performance of the appliances. It defines a number of daily tapping cycles for each domestic hot water use such as kitchen, shower, bath and a combination of these, together with corresponding test procedures, enabling the energy performances of combination boilers and water heaters to be compared and matched to the needs of the user.
The heat output of the appliances covered by this standard does not exceed 400 kW.
In the case of combination boilers, with or without storage tank, domestic hot water production is integrated or coupled, the whole being marketed as a single unit.
This standard only covers type testing.
- Standard48 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft48 pagesEnglish languagesale 10% offe-Library read for×1 day
This document is applicable to gas-fired appliances producing domestic hot water. It applies to both instantaneous and storage appliances; water-heaters and combination boilers that have:
- heat input not exceeding 70 kW; and
- hot water storage capacity (if any) not exceeding 500 l.
In the case of combination boilers, with or without storage tank, domestic hot water production is integrated or coupled, the whole being marketed as a single unit.
The present document sets out in qualitative and quantitative terms the performance in delivery of domestic hot water for a selected variety of uses. It also gives a system for presenting the information to the user.
- Standard32 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft32 pagesEnglish languagesale 10% offe-Library read for×1 day
- 09-Jun-2015
- 01-Nov-2015
- 91.140.65
- 2009/125/EC
- 2009/142/EC
- 814/2013
- M/495
- PLN
This European Standard defines the specifications and test methods for the construction, safety, rational use
of energy and fitness for purpose, environment and classification and marking of gas-fired storage water
heaters for domestic hot water uses, hereafter called “appliance”.
This European Standard applies to appliances:
— of selected types B1, B2, B3, B5, C1, C2, C3, C4, C5, C6, C7, C8, C9 according to CEN/TR 1749;
— fitted with atmospheric burners;
— using one or more combustible gases corresponding to the three gas families and the pressures indicated
in EN 437;
— of nominal heat input not exceeding 150 kW (net calorific value);
— fitted with electrically operated mechanical flue dampers that are positioned downstream of the heat
exchanger.
- Standard159 pagesEnglish languagesale 10% offe-Library read for×1 day
- 19-May-2012
- 08-Jun-2015
- 91.140.65
- 97.100.20
- 2009/142/EC
- M/BC/CEN/89/6
- PLN
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.