SIST EN 300 440-2 V1.2.1:2008
(Main)Electromagnetic compatibility and Radio spectrum Matters (ERM) - Short range devices - Radio equipment to be used in the 1 GHz to 40 GHz frequency range - Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
- Abstract
Update 300 440 -1 &-2 version 1.1.2 in accordance with the latest Regulatory and Market requirements. The present document applies to the following Short Range Device major equipment types:
1) Generic Short Range Devices, including alarms, identification systems, radio-determination, telecommand, telemetry etc.;
2) Radio Frequency IDentification (RFID);
3) Detection, movement and alert applications.
These radio equipment types are capable of operating in the permitted frequency bands within the 1 GHz to 40 GHz range as specified:
- either with a Radio Frequency (RF) output connection and dedicated antenna or with an integral antenna;
- for all types of modulation;
- with or without speech.
The present document covers fixed stations, mobile stations and portable stations.
Applications using Ultra Wide Band (UWB) technology are not covered by the present document.
The present document does not require measurements for radiated emissions below 25 MHz.
The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC (R&TTE Directive) [3].
This document does not apply to radio equipment for which a specific Harmonized EN applies as such Harmonized EN may specify additional EN requirements relevant to the presumption of conformity under article 3.2 of the R&TTE Directive [3].
- Status
- Published
- Publication Date
- 02-Jul-2008
- Withdrawal Date
- 31-Oct-2000
- Technical Committee
- MOC - Mobile Communications
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 10-Jun-2008
- Due Date
- 15-Aug-2008
- Completion Date
- 03-Jul-2008
- Mandate
- M/284
Buy Documents
ETSI EN 300 440-2 V1.2.1 (2008-03) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range; Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
ETSI EN 300 440-2 V1.2.1 (2008-05) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range; Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
SIST EN 300 440-2 V1.2.1:2008 is the SIST adoption of an ETSI harmonized European standard for short range devices in the 1 GHz to 40 GHz range. It specifies the radio requirements and compliance test approach used to show conformity with article 3.2 of the R&TTE Directive for generic SRD, RFID, and detection, movement and alert equipment.
What does SIST EN 300 440-2 V1.2.1:2008 specify?
SIST EN 300 440-2 V1.2.1:2008 covers the essential radio spectrum and electromagnetic compatibility requirements for short range radio equipment used in the 1 GHz to 40 GHz range. It applies to fixed, mobile and portable stations, and it is written to support conformity assessment under the R&TTE framework.
The scope includes generic short range devices, Radio Frequency IDentification (RFID), and detection, movement and alert applications. It also excludes applications using Ultra Wide Band (UWB) technology and equipment already covered by a specific Harmonized EN.
The document is organized into scope, references, definitions, technical requirements, testing for compliance, and two annexes.
| Annex | What it covers |
|---|---|
| Annex A | HS Requirements and conformance Test specifications Table (HS-RTT) for presumption of conformity under article 3.2 |
| Annex B | The EN title in the official languages |
What are the key requirements of SIST EN 300 440-2 V1.2.1:2008?
SIST EN 300 440-2 V1.2.1:2008 sets the minimum technical conditions that transmitters and receivers must meet, and it ties each requirement to a specific test. In practice, this means a supplier must know which equipment features are claimed, test the right functions, and document the results and measurement uncertainty.
Transmitter requirements
Clause 4.2.1 covers transmitter requirements for equivalent isotropically radiated power, permitted operating frequency range, and unwanted emissions in the spurious domain. A separate duty cycle requirement applies only to RFID transmitters in the designated 2,45 GHz case.
For a manufacturer, this means the transmitter must stay inside the allowed band, stay within the permitted radiated power, and control out-of-band emissions. If the product is RFID, duty cycle also becomes part of the compliance check.
Receiver requirements
Clause 4.2.2 covers adjacent channel selectivity, blocking or desensitization, and spurious radiations. These requirements apply according to the receiver category and whether the feature is invoked.
In practice, this is the part that shows whether the receiver can keep working in the presence of nearby signals and unwanted interference. Buyers and test labs use it to decide which receiver tests are relevant for a given design.
RFID and GBSAR cases
Clause 4.2.3 covers 2,45 GHz RFID systems, and clause 4.2.4 covers GBSAR systems. The GBSAR case has its own requirements for radiated power, operating frequency range, DAA threshold, DAA timing parameters, and unwanted emissions.
That means GBSAR equipment is treated as a special case, with extra checks on how it listens, detects, transmits, and remains within its allowed operating behavior.
Testing and measurement
Clause 5 requires testing under the declared operational environmental profile and at representative points within it. The test report must include measurement uncertainty, and the uncertainty values must meet the limit stated by the companion part.
Clause 5 also states that the measurement uncertainty shall be calculated using TR 100 028 principles and reported with the chosen coverage factor. For users, this is important because compliance is not just a pass/fail result - it also depends on how confidently the result was measured.
What terms does SIST EN 300 440-2 V1.2.1:2008 define?
SIST EN 300 440-2 V1.2.1:2008 uses the definitions, symbols and abbreviations from the R&TTE Directive and EN 300 440-1. A few terms are especially important for reading the document.
- Short Range Device (SRD) - the main equipment family covered by the standard, including generic devices, RFID, and detection, movement and alert applications.
- Radio Frequency IDentification (RFID) - the application area with specific transmitter rules, including a duty cycle condition in the 2,45 GHz case.
- GBSAR - a special application category with dedicated radiated power, frequency, DAA and timing requirements.
- Listen Before Talk (LBT) - an optional feature mentioned in the foreword as one of the technical developments reflected in this version.
- Detect And Avoid (DAA) - an optional feature used in the GBSAR requirements and tests to control when transmission may occur.
- Spurious domain - the frequency region where unwanted emissions are checked against limits.
- Equipment Category 1 / Category 2 - receiver classifications from EN 300 440-1 that determine which receiver tests apply.
Who uses SIST EN 300 440-2 V1.2.1:2008?
SIST EN 300 440-2 V1.2.1:2008 is used by manufacturers, test laboratories, conformity assessment teams, quality managers and buyers dealing with short range radio equipment. It is especially relevant when a product is being prepared for the R&TTE conformity route and needs documented transmitter and receiver compliance.
It also helps design teams decide which tests apply to a product variant, such as generic SRD, RFID, or GBSAR. For procurement and quality review, it shows what evidence should appear in the technical construction file and test report.
What changed in SIST EN 300 440-2 V1.2.1:2008 from the previous edition?
SIST EN 300 440-2 V1.2.1:2008 updates version 1.1.2. The foreword says the revision includes improvements based on technical developments in the SRD industry, including optional features such as Listen Before Talk (LBT) and Detect And Avoid (DAA).
Which standards are used with SIST EN 300 440-2 V1.2.1:2008?
SIST EN 300 440-2 V1.2.1:2008 depends on EN 300 440-1 and cites several supporting documents.
| Reference | What it contributes |
|---|---|
| ETSI EN 300 440-1 V1.4.1 | Technical characteristics, test methods, definitions, symbols, abbreviations, limit tables and equipment categories used throughout this part |
| ETSI EG 201 399 V2.1.1 | The modular structure used for candidate harmonized standards |
| ETSI TR 100 028 V1.4.1 | Principles for calculating measurement uncertainty |
| CEPT/ERC/REC 70-03 (2007) | SRD band use context that supports the frequency allocations discussed in the scope |
What does the SIST EN 300 440-2 V1.2.1:2008 document contain?
SIST EN 300 440-2 V1.2.1:2008 contains the requirement clauses, the matching test suites, and an HS-RTT table that links each requirement to its conformity status and test reference. It also includes environmental testing conditions, sample selection, and the rules for interpreting measurement results.
The document gives separate test paths for transmitter power, operating frequency, spurious emissions, receiver selectivity, blocking, and receiver spurious radiations. It also gives dedicated test sets for 2,45 GHz RFID and for GBSAR functions such as DAA timing and transmit on-time/off-time behavior.
Annex A is the practical cross-reference tool for compliance work, while Annex B provides the EN title in multiple official languages.
Relations
- Official Journal Project Relation
SIST EN 300 440-2 V1.1.2:2005 - Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range; Part 2: Harmonized EN under article 3.2 of the R&TTE Directive - Effective Date
- 23-Nov-2009
Buy Documents
ETSI EN 300 440-2 V1.2.1 (2008-03) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range; Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
ETSI EN 300 440-2 V1.2.1 (2008-05) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range; Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
Get Certified
Connect with accredited certification bodies for this standard
ANCE
Mexican certification and testing association.
Intertek Slovenia
Intertek testing, inspection, and certification services in Slovenia.
LNE (Laboratoire National de Métrologie et d'Essais)
French national laboratory for metrology and testing.
Sponsored listings
Frequently Asked Questions
SIST EN 300 440-2 V1.2.1:2008 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Electromagnetic compatibility and Radio spectrum Matters (ERM) - Short range devices - Radio equipment to be used in the 1 GHz to 40 GHz frequency range - Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive". This standard covers: Update 300 440 -1 &-2 version 1.1.2 in accordance with the latest Regulatory and Market requirements. The present document applies to the following Short Range Device major equipment types: 1) Generic Short Range Devices, including alarms, identification systems, radio-determination, telecommand, telemetry etc.; 2) Radio Frequency IDentification (RFID); 3) Detection, movement and alert applications. These radio equipment types are capable of operating in the permitted frequency bands within the 1 GHz to 40 GHz range as specified: - either with a Radio Frequency (RF) output connection and dedicated antenna or with an integral antenna; - for all types of modulation; - with or without speech. The present document covers fixed stations, mobile stations and portable stations. Applications using Ultra Wide Band (UWB) technology are not covered by the present document. The present document does not require measurements for radiated emissions below 25 MHz. The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC (R&TTE Directive) [3]. This document does not apply to radio equipment for which a specific Harmonized EN applies as such Harmonized EN may specify additional EN requirements relevant to the presumption of conformity under article 3.2 of the R&TTE Directive [3].
Update 300 440 -1 &-2 version 1.1.2 in accordance with the latest Regulatory and Market requirements. The present document applies to the following Short Range Device major equipment types: 1) Generic Short Range Devices, including alarms, identification systems, radio-determination, telecommand, telemetry etc.; 2) Radio Frequency IDentification (RFID); 3) Detection, movement and alert applications. These radio equipment types are capable of operating in the permitted frequency bands within the 1 GHz to 40 GHz range as specified: - either with a Radio Frequency (RF) output connection and dedicated antenna or with an integral antenna; - for all types of modulation; - with or without speech. The present document covers fixed stations, mobile stations and portable stations. Applications using Ultra Wide Band (UWB) technology are not covered by the present document. The present document does not require measurements for radiated emissions below 25 MHz. The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC (R&TTE Directive) [3]. This document does not apply to radio equipment for which a specific Harmonized EN applies as such Harmonized EN may specify additional EN requirements relevant to the presumption of conformity under article 3.2 of the R&TTE Directive [3].
SIST EN 300 440-2 V1.2.1:2008 is classified under the following ICS (International Classification for Standards) categories: 33.060.20 - Receiving and transmitting equipment; 33.100.01 - Electromagnetic compatibility in general. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 300 440-2 V1.2.1:2008 has the following relationships with other standards: It is inter standard links to SIST EN 300 440-2 V1.1.2:2005. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 300 440-2 V1.2.1:2008 is associated with the following European legislation: EU Directives/Regulations: 1999/5/EC, 2005-01-1864; Standardization Mandates: M/284. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
SIST EN 300 440-2 V1.2.1:2008 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
Final draft ETSI EN 300 440-2 V1.2.1 (2008-03)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Short range devices;
Radio equipment to be used
in the 1 GHz to 40 GHz frequency range;
Part 2: Harmonized EN covering essential requirements
of article 3.2 of the R&TTE Directive
2 Final draft ETSI EN 300 440-2 V1.2.1 (2008-03)
Reference
REN/ERM-TG28-0417-2
Keywords
radio, regulation, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2008.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
3 Final draft ETSI EN 300 440-2 V1.2.1 (2008-03)
Contents
Intellectual Property Rights.5
Foreword.5
Introduction .5
1 Scope.6
2 References.7
2.1 Normative references.7
2.2 Informative references.7
3 Definitions, symbols and abbreviations .8
3.1 Definitions.8
3.2 Symbols.8
3.3 Abbreviations.8
4 Technical requirements specifications .8
4.1 Environmental profile.8
4.2 Conformance requirements.8
4.2.1 Transmitter requirements.8
4.2.1.1 Equivalent isotropically radiated power.8
4.2.1.2 Permitted range of operating frequencies.8
4.2.1.3 Unwanted emissions in the spurious domain .8
4.2.1.4 Duty cycle.9
4.2.2 Receiver requirements.9
4.2.2.1 Adjacent channel selectivity.9
4.2.2.2 Blocking or desensitization .9
4.2.2.3 Spurious radiations.9
4.2.3 2,45 GHz RFID systems .9
4.2.4 GBSAR systems.9
4.2.4.1 Effective radiated power .9
4.2.4.2 Permitted range of operating frequencies.9
4.2.4.3 DAA threshold.9
4.2.4.3.1 DAA timing parameters.10
4.2.4.4 Unwanted emissions in the spurious domain .10
5 Testing for compliance with technical requirements.10
5.1 Description of testing for compliance with technical requirements .10
5.1.1 Environmental conditions for testing.10
5.1.1.1 Normal and extreme test-conditions.10
5.1.1.2 Test power source .10
5.1.2 Choice of samples for test suites.10
5.2 Interpretation of the measurement results .11
5.3 Essential transmitter test suites.11
5.3.1 Equivalent isotropically radiated power .11
5.3.2 Permitted range of operation frequencies .11
5.3.3 Unwanted emissions in the spurious domain.11
5.4 Essential receiver test suites .12
5.4.1 Adjacent channel selectivity .12
5.4.2 Blocking or desensitization.12
5.4.3 Spurious radiations.12
5.5 Tests for RFID systems at 2,45 GHz.12
5.6 Tests for GBSAR systems.12
5.6.1 Effective radiated power.12
5.6.2 Permitted range of operating frequencies .12
5.6.3 DAA threshold.12
5.6.4 DAA timing parameters.12
5.6.4.1 Minimum listen time.12
5.6.4.2 Minimum listen time after detection .12
ETSI
4 Final draft ETSI EN 300 440-2 V1.2.1 (2008-03)
5.6.4.3 Maximum transmitter on-time .13
5.6.4.4 Minimum transmitter off-time .13
5.6.5 Unwanted emissions in the spurious domain.13
Annex A (normative): HS Requirements and conformance Test specifications Table (HS-
RTT).14
Annex B (informative): The EN title in the official languages .16
History .17
ETSI
5 Final draft ETSI EN 300 440-2 V1.2.1 (2008-03)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards Two-step Approval Procedure.
The present document includes improvements to the previous version of the standard that take advantage of technical
developments within the SRD industry. In particular this includes optional features such as Listen Before Talk (LBT)
and Detect And Avoid (DAA).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC (as amended) [2] laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC of the European Parliament and of
the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive") [3].
Technical specifications relevant to Directive 1999/5/EC [3] are given in annex A.
The present document is part 2 of a multi-part deliverable covering Electromagnetic compatibility and Radio spectrum
Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range, as identified
below:
Part 1: "Technical characteristics and test methods";
Part 2: "Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [3]. The modular
structure is shown in EG 201 399 [5].
ETSI
6 Final draft ETSI EN 300 440-2 V1.2.1 (2008-03)
1 Scope
The present document applies to the following Short Range Device major equipment types:
1) Generic Short Range Devices, including alarms, identification systems, radio-determination, telecommand,
telemetry etc.;
2) Radio Frequency IDentification (RFID);
3) Detection, movement and alert applications.
These radio equipment types are capable of operating in the permitted frequency bands within the 1 GHz to 40 GHz
range as specified in table 1:
- either with a Radio Frequency (RF) output connection and dedicated antenna or with an integral antenna;
- for all types of modulation;
- with or without speech.
Table 1 shows a list of the frequency bands as designated by the European Commission Decision on Short Range
Devices and the CEPT/ERC/REC 70-03 [4] as known at the date of publication of the present document.
Table 1: Short Range Devices within the 1 GHz to 40 GHz frequency band
Frequency Bands Applications Notes
Transmit and Receive 2 400 MHz to 2 483,5 MHz Generic use
Transmit and Receive 2 400 MHz to 2 483,5 MHz Detection, movement and alert
applications
Transmit and Receive (a) 2 446 MHz to 2 454 MHz RFID See annex C of EN 300 440-1 [1]
Transmit and Receive (b) 2 446 MHz to 2 454 MHz RFID See annex C of EN 300 440-1 [1]
Transmit and Receive 5 725 MHz to 5 875 MHz Generic use
Transmit and Receive 9 200 MHz to 9 500 MHz Detection, movement and alert
applications
Transmit and Receive 9 500 MHz to 9 975 MHz Detection, movement and alert
applications
Transmit and Receive 10,5 GHz to 10,6 GHz For detection, movement and
alert applications
Transmit and Receive 13,4 GHz to 14,0 GHz Detection, movement and alert
applications
Transmit and Receive 17,1 GHz to 17,3 GHz GBSAR detection, movement See annex E of EN 300 440-1 [1]
and alert applications
Transmit and Receive 24,00 GHz to 24,25 GHz Generic use and for detection,
movement and alert
applications
NOTE: (a) and (b) refer to two different operational restrictions for different power levels in the same frequency band.
NOTE 1: It should be noted that table 1 represents the most widely implemented position within the European
Union and the CEPT countries, but it should not be assumed that all designated bands are available in all
countries.
NOTE 2: In addition, it should be noted that other frequency bands may be available in a country within the
frequency range 1 GHz to 40 GHz covered by the present document.
NOTE 3: On non-harmonized parameters, national administrations may impose certain conditions such as the type
of modulation, frequency, channel/frequency separations, maximum transmitter radiated power, duty
cycle, and the inclusion of an automatic transmitter shut-off facility, as a condition for the issue of an
individual or general licence, or as a condition for use under licence exemption.
The present document covers fixed stations, mobile stations and portable stations.
Applications using Ultra Wide Band (UWB) technology are not covered by the present document.
ETSI
7 Final draft ETSI EN 300 440-2 V1.2.1 (2008-03)
The present document does not require measurements for radiated emissions below 25 MHz.
The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC (R&TTE Directive) [3].
This document does not apply to radio equipment for which a specific Harmonized EN applies as such Harmonized EN
may specify additional EN requirements relevant to the presumption of conformity under article 3.2 of the R&TTE
Directive [3].
NOTE 4: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be
...
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Short range devices;
Radio equipment to be used
in the 1 GHz to 40 GHz frequency range;
Part 2: Harmonized EN covering essential requirements
of article 3.2 of the R&TTE Directive
2 ETSI EN 300 440-2 V1.2.1 (2008-05)
Reference
REN/ERM-TG28-0417-2
Keywords
radio, regulation, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2008.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
3 ETSI EN 300 440-2 V1.2.1 (2008-05)
Contents
Intellectual Property Rights.5
Foreword.5
Introduction .5
1 Scope.6
2 References.7
2.1 Normative references.7
2.2 Informative references.7
3 Definitions, symbols and abbreviations .8
3.1 Definitions.8
3.2 Symbols.8
3.3 Abbreviations.8
4 Technical requirements specifications .8
4.1 Environmental profile.8
4.2 Conformance requirements.8
4.2.1 Transmitter requirements.8
4.2.1.1 Equivalent isotropically radiated power.8
4.2.1.2 Permitted range of operating frequencies.8
4.2.1.3 Unwanted emissions in the spurious domain .8
4.2.1.4 Duty cycle.9
4.2.2 Receiver requirements.9
4.2.2.1 Adjacent channel selectivity.9
4.2.2.2 Blocking or desensitization .9
4.2.2.3 Spurious radiations.9
4.2.3 2,45 GHz RFID systems .9
4.2.4 GBSAR systems.9
4.2.4.1 Effective radiated power .9
4.2.4.2 Permitted range of operating frequencies.9
4.2.4.3 DAA threshold.9
4.2.4.3.1 DAA timing parameters.10
4.2.4.4 Unwanted emissions in the spurious domain .10
5 Testing for compliance with technical requirements.10
5.1 Description of testing for compliance with technical requirements .10
5.1.1 Environmental conditions for testing.10
5.1.1.1 Normal and extreme test-conditions.10
5.1.1.2 Test power source .10
5.1.2 Choice of samples for test suites.10
5.2 Interpretation of the measurement results .11
5.3 Essential transmitter test suites.11
5.3.1 Equivalent isotropically radiated power .11
5.3.2 Permitted range of operation frequencies .11
5.3.3 Unwanted emissions in the spurious domain.11
5.4 Essential receiver test suites .12
5.4.1 Adjacent channel selectivity .12
5.4.2 Blocking or desensitization.12
5.4.3 Spurious radiations.12
5.5 Tests for RFID systems at 2,45 GHz.12
5.6 Tests for GBSAR systems.12
5.6.1 Effective radiated power.12
5.6.2 Permitted range of operating frequencies .12
5.6.3 DAA threshold.12
5.6.4 DAA timing parameters.12
5.6.4.1 Minimum listen time.12
5.6.4.2 Minimum listen time after detection .12
ETSI
4 ETSI EN 300 440-2 V1.2.1 (2008-05)
5.6.4.3 Maximum transmitter on-time .13
5.6.4.4 Minimum transmitter off-time .13
5.6.5 Unwanted emissions in the spurious domain.13
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT).14
Annex B (informative): The EN title in the official languages .16
History .18
ETSI
5 ETSI EN 300 440-2 V1.2.1 (2008-05)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document includes improvements to the previous version of the standard that take advantage of technical
developments within the SRD industry. In particular this includes optional features such as Listen Before Talk (LBT)
and Detect And Avoid (DAA).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC (as amended) [2] laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [3] of the European Parliament and
of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive") [3].
Technical specifications relevant to Directive 1999/5/EC [3] are given in annex A.
The present document is part 2 of a multi-part deliverable covering Electromagnetic compatibility and Radio spectrum
Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range, as identified
below:
Part 1: "Technical characteristics and test methods";
Part 2: "Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates
Date of adoption of this EN: 9 May 2008
Date of latest announcement of this EN (doa): 31 August 2008
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 28 February 2009
Date of withdrawal of any conflicting National Standard (dow): 28 February 2010
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [3]. The modular
structure is shown in EG 201 399 [5].
ETSI
6 ETSI EN 300 440-2 V1.2.1 (2008-05)
1 Scope
The present document applies to the following Short Range Device major equipment types:
1) Generic Short Range Devices, including alarms, identification systems, radio-determination, telecommand,
telemetry etc.;
2) Radio Frequency IDentification (RFID);
3) Detection, movement and alert applications.
These radio equipment types are capable of operating in the permitted frequency bands within the 1 GHz to 40 GHz
range as specified in table 1:
- either with a Radio Frequency (RF) output connection and dedicated antenna or with an integral antenna;
- for all types of modulation;
- with or without speech.
Table 1 shows a list of the frequency bands as designated by the European Commission Decision on Short Range
Devices and the CEPT/ERC/REC 70-03 [4] as known at the date of publication of the present document.
Table 1: Short Range Devices within the 1 GHz to 40 GHz frequency band
Frequency Bands Applications Notes
Transmit and Receive 2 400 MHz to 2 483,5 MHz Generic use
Transmit and Receive 2 400 MHz to 2 483,5 MHz Detection, movement and alert
applications
Transmit and Receive (a) 2 446 MHz to 2 454 MHz RFID See annex C of EN 300 440-1 [1]
Transmit and Receive (b) 2 446 MHz to 2 454 MHz RFID See annex C of EN 300 440-1 [1]
Transmit and Receive 5 725 MHz to 5 875 MHz Generic use
Transmit and Receive 9 200 MHz to 9 500 MHz Detection, movement and alert
applications
Transmit and Receive 9 500 MHz to 9 975 MHz Detection, movement and alert
applications
Transmit and Receive 10,5 GHz to 10,6 GHz For detection, movement and
alert applications
Transmit and Receive 13,4 GHz to 14,0 GHz Detection, movement and alert
applications
Transmit and Receive 17,1 GHz to 17,3 GHz GBSAR detection, movement See annex E of EN 300 440-1 [1]
and alert applications
Transmit and Receive 24,00 GHz to 24,25 GHz Generic use and for detection,
movement and alert
applications
NOTE: (a) and (b) refer to two different operational restrictions for different power levels in the same frequency band.
NOTE 1: It should be noted that table 1 represents the most widely implemented position within the European
Union and the CEPT countries, but it should not be assumed that all designated bands are available in all
countries.
NOTE 2: In addition, it should be noted that other frequency bands may be available in a country within the
frequency range 1 GHz to 40 GHz covered by the present document.
NOTE 3: On non-harmonized parameters, national administrations may impose certain conditions such as the type
of modulation, frequency, channel/frequency separations, maximum transmitter radiated power, duty
cycle, and the inclusion of an automatic transmitter shut-off facility, as a condition for the issue of an
individual or general licence, or as a condition for use under licence exemption.
The present document covers fixed stations, mobile stations and portable stations.
Applications using Ultra Wide Band (UWB) technology are not covered by the present document.
The present document does not require measurements for radiated emissions below 25 MHz.
ETSI
7 ETSI EN 300 440-2 V1.2.1 (2008-05)
The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC (R&TTE Directive) [3].
This document does not apply to radio equipment for which a specific Harmonized EN applies as such Harmonized EN
may specify additional EN requirements relevant to the presumption of conformity under article 3.2 of the R&TTE
Directive [3].
NOTE 4: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
For online referenced documents, information sufficient to identify and locate the source shall be provided. Preferably,
the primary source of the referenced document should be cited, in order to ensure traceability. Furthermore, the
reference should, as far as possible, remain valid for the expected life of the document. The reference shall include the
method of access to the referenced document and the full network address, with the same punctuation and use of upper
case and lower case letters.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] ETSI EN 300 440-1 (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range;
Part 1: Technical characteristics and test methods".
2.2 Informative references
The following referenced documents are not essential to the use of the present document but they assist the user with
regard to a particular subject area. For non-specific references, the latest version of the referenced document (including
any amendments) applies.
[2] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[3] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[4] CEPT/ERC/REC 70-03 (2007): "Relating to the use of Short Range Devices (SRD)".
ETSI
8 ETSI EN 300 440-2 V1.2.1 (2008-05)
[5] ETSI EG 201 399 (V2.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
A guide to the production of candidate Harmonized Standards for application under the R&TTE
Directive".
[6] ETSI TR 100 028 (V1.4.1) (2001-12) (all parts): "Electromagnetic compatibility and Radio
spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment
characteristics".
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in the R&TTE Directive [3] and
EN 300 440-1 [1] apply.
3.2 Symbols
For the purposes of the present document, the symbols given in EN 300 440-1 [1] apply.
3.3 Abbreviations
For the purpo
...
SLOVENSKI STANDARD
01-september-2008
(OHNWURPDJQHWQD]GUXåOMLYRVWLQ]DGHYHY]YH]L]UDGLMVNLPVSHNWURP (50
1DSUDYHNUDWNHJDGRVHJD5DGLMVNDRSUHPD]DXSRUDERYIUHNYHQþQHPREPRþMX
RG*+]GR*+]GHO +DUPRQL]LUDQL(1NL]DMHPDELVWYHQH]DKWHYHþOHQD
GLUHNWLYH5 77(
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Short range devices -
Radio equipment to be used in the 1 GHz to 40 GHz frequency range -
Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE
Directive
Ta slovenski standard je istoveten z: EN 300 440-2 Version 1.2.1
ICS:
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Short range devices;
Radio equipment to be used
in the 1 GHz to 40 GHz frequency range;
Part 2: Harmonized EN covering essential requirements
of article 3.2 of the R&TTE Directive
2 ETSI EN 300 440-2 V1.2.1 (2008-05)
Reference
REN/ERM-TG28-0417-2
Keywords
radio, regulation, SRD, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2008.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
3 ETSI EN 300 440-2 V1.2.1 (2008-05)
Contents
Intellectual Property Rights.5
Foreword.5
Introduction .5
1 Scope.6
2 References.7
2.1 Normative references.7
2.2 Informative references.7
3 Definitions, symbols and abbreviations .8
3.1 Definitions.8
3.2 Symbols.8
3.3 Abbreviations.8
4 Technical requirements specifications .8
4.1 Environmental profile.8
4.2 Conformance requirements.8
4.2.1 Transmitter requirements.8
4.2.1.1 Equivalent isotropically radiated power.8
4.2.1.2 Permitted range of operating frequencies.8
4.2.1.3 Unwanted emissions in the spurious domain .8
4.2.1.4 Duty cycle.9
4.2.2 Receiver requirements.9
4.2.2.1 Adjacent channel selectivity.9
4.2.2.2 Blocking or desensitization .9
4.2.2.3 Spurious radiations.9
4.2.3 2,45 GHz RFID systems .9
4.2.4 GBSAR systems.9
4.2.4.1 Effective radiated power .9
4.2.4.2 Permitted range of operating frequencies.9
4.2.4.3 DAA threshold.9
4.2.4.3.1 DAA timing parameters.10
4.2.4.4 Unwanted emissions in the spurious domain .10
5 Testing for compliance with technical requirements.10
5.1 Description of testing for compliance with technical requirements .10
5.1.1 Environmental conditions for testing.10
5.1.1.1 Normal and extreme test-conditions.10
5.1.1.2 Test power source .10
5.1.2 Choice of samples for test suites.10
5.2 Interpretation of the measurement results .11
5.3 Essential transmitter test suites.11
5.3.1 Equivalent isotropically radiated power .11
5.3.2 Permitted range of operation frequencies .11
5.3.3 Unwanted emissions in the spurious domain.11
5.4 Essential receiver test suites .12
5.4.1 Adjacent channel selectivity .12
5.4.2 Blocking or desensitization.12
5.4.3 Spurious radiations.12
5.5 Tests for RFID systems at 2,45 GHz.12
5.6 Tests for GBSAR systems.12
5.6.1 Effective radiated power.12
5.6.2 Permitted range of operating frequencies .12
5.6.3 DAA threshold.12
5.6.4 DAA timing parameters.12
5.6.4.1 Minimum listen time.12
5.6.4.2 Minimum listen time after detection .12
ETSI
4 ETSI EN 300 440-2 V1.2.1 (2008-05)
5.6.4.3 Maximum transmitter on-time .13
5.6.4.4 Minimum transmitter off-time .13
5.6.5 Unwanted emissions in the spurious domain.13
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT).14
Annex B (informative): The EN title in the official languages .16
History .18
ETSI
5 ETSI EN 300 440-2 V1.2.1 (2008-05)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document includes improvements to the previous version of the standard that take advantage of technical
developments within the SRD industry. In particular this includes optional features such as Listen Before Talk (LBT)
and Detect And Avoid (DAA).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC (as amended) [2] laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [3] of the European Parliament and
of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive") [3].
Technical specifications relevant to Directive 1999/5/EC [3] are given in annex A.
The present document is part 2 of a multi-part deliverable covering Electromagnetic compatibility and Radio spectrum
Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range, as identified
below:
Part 1: "Technical characteristics and test methods";
Part 2: "Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates
Date of adoption of this EN: 9 May 2008
Date of latest announcement of this EN (doa): 31 August 2008
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 28 February 2009
Date of withdrawal of any conflicting National Standard (dow): 28 February 2010
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [3]. The modular
structure is shown in EG 201 399 [5].
ETSI
6 ETSI EN 300 440-2 V1.2.1 (2008-05)
1 Scope
The present document applies to the following Short Range Device major equipment types:
1) Generic Short Range Devices, including alarms, identification systems, radio-determination, telecommand,
telemetry etc.;
2) Radio Frequency IDentification (RFID);
3) Detection, movement and alert applications.
These radio equipment types are capable of operating in the permitted frequency bands within the 1 GHz to 40 GHz
range as specified in table 1:
- either with a Radio Frequency (RF) output connection and dedicated antenna or with an integral antenna;
- for all types of modulation;
- with or without speech.
Table 1 shows a list of the frequency bands as designated by the European Commission Decision on Short Range
Devices and the CEPT/ERC/REC 70-03 [4] as known at the date of publication of the present document.
Table 1: Short Range Devices within the 1 GHz to 40 GHz frequency band
Frequency Bands Applications Notes
Transmit and Receive 2 400 MHz to 2 483,5 MHz Generic use
Transmit and Receive 2 400 MHz to 2 483,5 MHz Detection, movement and alert
applications
Transmit and Receive (a) 2 446 MHz to 2 454 MHz RFID See annex C of EN 300 440-1 [1]
Transmit and Receive (b) 2 446 MHz to 2 454 MHz RFID See annex C of EN 300 440-1 [1]
Transmit and Receive 5 725 MHz to 5 875 MHz Generic use
Transmit and Receive 9 200 MHz to 9 500 MHz Detection, movement and alert
applications
Transmit and Receive 9 500 MHz to 9 975 MHz Detection, movement and alert
applications
Transmit and Receive 10,5 GHz to 10,6 GHz For detection, movement and
alert applications
Transmit and Receive 13,4 GHz to 14,0 GHz Detection, movement and alert
applications
Transmit and Receive 17,1 GHz to 17,3 GHz GBSAR detection, movement See annex E of EN 300 440-1 [1]
and alert applications
Transmit and Receive 24,00 GHz to 24,25 GHz Generic use and for detection,
movement and alert
applications
NOTE: (a) and (b) refer to two different operational restrictions for different power levels in the same frequency band.
NOTE 1: It should be noted that table 1 represents the most widely implemented position within the European
Union and the CEPT countries, but it should not be assumed that all designated bands are available in all
countries.
NOTE 2: In addition, it should be noted that other frequency bands may be available in a country within the
frequency range 1 GHz to 40 GHz covered by the present document.
NOTE 3: On non-harmonized parameters, national administrations may impose certain conditions such as the type
of modulation, frequency, channel/frequency separations, maximum transmitter radiated power, duty
cycle, and the inclusion of an automatic transmitter shut-off facility, as a condition for the issue of an
individual or general licence, or as a condition for use under licence exemption.
The present document covers fixed stations, mobile stations and portable stations.
Applications using Ultra Wide Band (UWB) technology are not covered by the present document.
The present document does not require measurements for radiated emissions below 25 MHz.
ETSI
7 ETSI EN 300 440-2 V1.2.1 (2008-05)
The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC (R&TTE Directive) [3].
This document does not apply to radio equipment for which a specific Harmonized EN applies as such Harmonized EN
may specify additional EN requirements relevant to the presumption of conformity under article 3.2 of the R&TTE
Directive [3].
NOTE 4: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
For online referenced documents, information sufficient to identify and locate the source shall be provided. Preferably,
the primary source of the referenced document should be cited, in order to ensure traceability. Furthermore, the
reference should, as far as possible, remain valid for the expected life of the document. The reference shall include the
method of access to the referenced document and the full network address, with the same punctuation and use of upper
case and lower case letters.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] ETSI EN 300 440-1 (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range;
Part 1: Technical characteristics and test methods".
2.2 Informative references
The following referenced documents are not essential to the use of the present document but they assist the user with
regard to a particular subject area. For non-specific references, the latest version of the referenced document (including
any amendments) applies.
[2] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[3] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[4] CEPT/ERC/REC 70-03 (2007): "Relating to the use of Short Range Devices (SRD)".
ETSI
8 ETSI EN 300 440-2 V1.2.1 (2008-05)
[5] ETSI EG 201 399 (V2.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
A guide to the production of candidate Harmonized Standards for application under the R&TTE
Directive".
[6] ETSI
...