Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 11: Positive pressure ventilation systems

This European standard specifies aerodynamic, acoustic and electrical power performance test measurements for un-ducted / ducted continuous supply ventilation / supply air ventilation units in a single room or a single dwelling used in residential ventilation.
In general such units contain:
- fan;
- air filter;
- control system.
Units may also include:
- grille or air distribution device;
- heating device;
- solar or thermal collectors (water or air);
- electrical;
- hydronic;
- sound attenuators;
- bypass dampers;
- mixing devices.
Supplementary heating may also be provided by solar air collector air or ground source heat pumps etc., the performance of these supplementary components are not covered by this standard.

Lüftung von Gebäuden - Leistungsprüfung von Bauteilen/Produkten für die Lüftung von Wohnungen - Teil 11: Überdruck-Zuluftsysteme

Diese Europäische Norm legt Prüfmessungen der aerodynamischen, akustischen und elektrischen Leistung für Zulufteinheiten mit kontinuierlicher Versorgung ohne Luftführung/mit Luftleitung fest, die zum Zwecke der Wohnungs¬lüftung in einem einzelnen Raum oder einer einzelnen Wohnung eingesetzt werden.
Im Allgemeinen umfassen derartige Einheiten Folgendes:
-   Ventilator;
-   Luftfilter;
-   Regelsystem.
Die Einheiten können auch Folgendes umfassen:
-   Luftgitter oder Luftverteilungseinrichtung;
-   Heizvorrichtung;
-   Solar- bzw. thermische Kollektoren (Wasser oder Luft);
-   elektrisch;
-   hydronisch;
-   Schalldämpfer;
-   Bypass-Drosselelemente;
-   Mischvorrichtungen.
Eine Zusatzheizfunktion kann auch durch Solar-Luft-Kollektoren oder Luft- bzw. Erdwärmepumpen usw. bereitgestellt werden; die Leistung dieser zusätzlichen Bauteile ist nicht durch diese Norm abgedeckt.

Ventilation des bâtiments - Essais de performance des composants/produits pour la ventilation des logements - Partie 11: Systèmes de ventilation à pression positive

La présente Norme européenne spécifie les mesures d’essai de performance aérodynamiques, acoustiques et énergétiques pour la ventilation de soufflage continue/les caissons de ventilation d’air de soufflage non raccordés/centralisé dans une pièce ou un logement individuel utilisés en ventilation résidentielle.
En règle générale, ces caissons comprennent :
-   un ventilateur ;
-   un filtre à air ;
-   un système de commande.
Les caissons peuvent également comprendre :
-   une grille ou un dispositif de distribution d’air ;
-   un dispositif de chauffage ;
-   par capteurs solaires ou thermiques (eau ou air) ;
-   électrique ;
-   hydronique ;
-   des atténuateurs de bruit ;
-   des registres de dérivation ;
-   des dispositifs mélangeurs.
Le chauffage d’appoint peut également être assuré par un capteur solaire d’air ou des pompes à chaleur géothermiques, etc. La performance de ces composants supplémentaires n’est pas couverte par la présente norme.

Prezračevanje stavb - Preskušanje lastnosti stanovanjskih prezračevalnih komponent/izdelkov - 11. del: Prezračevalni sistemi z nadtlakom

Ta evropski standard opredeljuje meritve preskusa aerodinamične, akustične in električne zmogljivosti za necevne/cevne enote za stalno prezračevanje/dovajanje zraka v eni sobi ali eni stanovanjski enoti, ki se uporabljajo za stanovanja.
Taka enota običajno vsebuje:
– ventilator;
– zračni filter;
– krmilni sistem.
Enote lahko vsebujejo tudi:
– rešetke;
– naprave za ogrevanje;
– sončne ali toplotne kolektorje (voda ali zrak);
– električne elemente;
– vodne elemente;
– dušilnike zvoka;
– obvodne dušilnike;
– mešalne naprave.
Dodatno ogrevanje se lahko zagotovi s sončnimi zbiralniki ali toplotnimi črpalkami s talnim virom toplote itd. Lastnosti teh dodatnih komponent niso zajete v tem standardu.

General Information

Status
Published
Public Enquiry End Date
14-Mar-2013
Publication Date
09-Aug-2015
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
09-Jul-2015
Due Date
13-Sep-2015
Completion Date
10-Aug-2015

Buy Standard

Standard
EN 13141-11:2015
English language
27 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.HYDOQLKLüftung von Gebäuden - Leistungsprüfung von Bauteilen/Produkten für die Lüftung von Wohnungen - Teil 11: Überdruck-ZuluftsystemeVentilation des bâtiments - Essais de performance des composants/produits pour la ventilation des logements - Partie 11: Systèmes de ventilation à pression positiveVentilation for buildings - Performance testing of components/products for residential ventilation - Part 11: Positive pressure ventilation systems91.140.30VLVWHPLVentilation and air-conditioningICS:Ta slovenski standard je istoveten z:EN 13141-11:2015SIST EN 13141-11:2015en,fr,de01-september-2015SIST EN 13141-11:2015SLOVENSKI
STANDARD



SIST EN 13141-11:2015



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13141-11
May 2015 ICS 91.140.30 English Version
Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 11: Supply ventilation units
Ventilation des bâtiments - Essais de performance des composants/produits pour la ventilation des logements - Partie 11 : Unités de ventilation par insufflation
Lüftung von Gebäuden - Leistungsprüfung von Bauteilen/Produkten für die Lüftung von Wohnungen - Teil 11: Zuluftsysteme This European Standard was approved by CEN on 16 April 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13141-11:2015 ESIST EN 13141-11:2015



EN 13141-11:2015 (E) 2 Contents Page Foreword .3 Introduction .4 1 Scope .6 2 Normative references .6 3 Terms and definitions .7 4 Symbols and abbreviations .9 5 Declaration of intended use .9 6 Performance testing of aerodynamic characteristics .9 6.1 General .9 6.2 External leakage. 10 6.3 Airflow . 11 6.3.1 Un-ducted room unit. 11 6.3.2 Ducted unit . 11 6.4 Acoustic characteristic . 11 6.4.1 General . 11 6.4.2 Un-ducted unit . 12 6.4.3 Ducted unit . 14 6.5 Electrical power input . 17 7 Test report . 18 7.1 Presentation of results . 18 7.2 General information . 18 7.3 Product specifications . 18 7.4 External leakage. 19 7.5 Airflow . 19 7.6 Acoustic characteristics . 20 7.7 Electrical power input . 20 Annex A (informative)
Typical applications . 21 Annex B (informative)
Sound insulating box . 24 Annex C (informative)
Acoustic box . 25 Annex D (normative)
Pressure leakage test method . 26 Bibliography . 27
SIST EN 13141-11:2015



EN 13141-11:2015 (E) 3 Foreword This document (EN 13141-11:2015) has been prepared by Technical Committee CEN/TC 156 “Ventilation for buildings”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2015, and conflicting national standards shall be withdrawn at the latest by November 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. EN 13141 consists of the following parts, under the general title Ventilation for buildings testing of componentsiproducts for residential ventilation: — mart 1: bxternally and internally mounted air transfer devices — mart l: bxhaust and supply air terminal devices — mart 3: Range hoods for residential use — mart 4: Fans used in residential ventilation systems — mart o: Cowls and roof outlet terminal devices — mart p: bxhaust ventilation system packages used in a single dwelling — mart 7: merformance testing of a mechanical supply and exhaust ventilation units bincluding heat recoveryc for mechanical ventilation systems intended for single family dwellings — mart 8: merformance testing of un-ducted mechanical supply and exhaust ventilation units bincluding heat recoveryc for mechanical ventilation systems intended for a single room — mart 9: bxternally mounted humidity controlled air transfer device — mart 1M: eumidity controlled extract air terminal device — mart 11: pupply ventilation units According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 13141-11:2015



EN 13141-11:2015 (E) 4 Introduction The position of this document in the field of standards for the mechanical building services is shown in Figure 1. SIST EN 13141-11:2015



EN 13141-11:2015 (E) 5
Figure 1 — Position of EN 13141-11 in the field of the mechanical building services SIST EN 13141-11:2015



EN 13141-11:2015 (E) 6 1 Scope 1.1 This European Standard specifies aerodynamic, acoustic and electrical power performance test measurements for
— un-ducted continuous supply ventilation units in a single room; — ducted continuous supply ventilation units in a single room; — un-ducted supply air ventilation units in a single room; — ducted supply air ventilation units in a single room;
— centralised unit for whole dwelling; used in residential ventilation. In general such units contain the following elements: — fan; — air filter; — control system. 1.2 This European Standard does not cover the following: — grilles, air delivery or air supply devices when the unit is ducted; — sound attenuation; — any heating devices or pre-heaters. 1.3 Safety requirements are given in EN 60335-2-80:2003 and its A2:2009 [2]. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 306, eeat exchangers - Methods of measuring the parameters necessary for establishing the performance EN 12792:2003, Ventilation for buildings - pymbolsf terminology and graphical symbols EN 13141-4:2011, Ventilation for buildings - merformance testing of componentsiproducts for residential ventilation - mart 4: cans used in residential ventilation systems EN ISO 717-1, Acoustics - oating of sound insulation in buildings and of building elements - mart 1: Airborne sound insulation bfpl 717-1) EN ISO 3741, Acoustics - aetermination of sound power levels and sound energy levels of noise sources using sound pressure - mrecision methods for reverberation test rooms bfpl m741c EN ISO 3743-1, Acoustics - aetermination of sound power levels and sound energy levels of noise sources using sound pressure - bngineering methods for small movable sources in reverberant fields - mart 1: Comparison method for a hard-walled test room bfpl m74m-1) SIST EN 13141-11:2015



EN 13141-11:2015 (E) 7 EN ISO 3743-2, Acoustics - aetermination of sound power levels of noise sources using sound pressure - bngineering methods for smallf movable sources in reverberant fields - mart l: Methods for special reverberation test rooms bfpl m74m-2) EN ISO 3744, Acoustics - aetermination of sound power levels and sound energy levels of noise sources using sound pressure - bngineering methods for an essentially free field over a reflecting plane bfpl m744c EN ISO 3745, Acoustics - aetermination of sound power levels and sound energy levels of noise sources using sound pressure - mrecision methods for anechoic rooms and hemi-anechoic rooms bfpl m74oc EN ISO 5135, Acoustics - aetermination of sound power levels of noise from air-terminal devicesf air-terminal unitsf dampers and valves by measurement in a reverberation room bfpl o1moc EN ISO 5136, Acoustics - aetermination of sound power radiated into a duct by fans and other air-moving devices - fn-duct method bfpl o1mpc EN ISO 9614-1, Acoustics - aetermination of sound power levels of noise sources using sound intensity - mart 1: Measurement at discrete points bfpl 9p14-1) EN ISO 9614-2, Acoustics - aetermination of sound power levels of noise sources using sound intensity - mart l: Measurement by scanning bfpl 9p14-2) EN ISO 9614-3, Acoustics - aetermination of sound power levels of noise sources using sound intensity - mart m: mrecision method for measurement by scanning bfpl 9p14-3) EN ISO 10140-2, Acoustics - iaboratory measurement of sound insulation of building elements - mart l: Measurement of airborne sound insulation bfpl 1M14M-2) EN ISO 5801, fndustrial fans - merformance testing using standardized airways bfpl o8M1) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12792:2003 and the following apply. 3.1 test voltage voltage to be used for supplying the components during the testing [SOURCE: EN 13141-7:2010 [1], definition 3.1.9] 3.2 fan unit casing incorporating a fan and provided with spigots [SOURCE: EN 12792:2003, definition 164] 3.3 external leakage qve leakage to or from the air flowing inside the casing of the unit to or from the surrounding air [SOURCE: EN 13141-7:2010 [1], definition 3.1.1] SIST EN 13141-11:2015



EN 13141-11:2015 (E) 8 3.4 declared maximum air volume flow qvd air volume flow corresponding to the declared total pressure ptUd of the unit at the maximum setting for standard air conditions (20 °C, 101 325 Pa) Note 1 to entry: Not including any boost function used for short time duty (for example purge ventilation). Note 2 to entry: For category A units ptUd = 0. Note 3 to entry: qvd is expressed in m3„s−1 or l„s−1. 3.5 electric power input PE average electrical power input to the equipment within a defined interval of time obtained from: — the power input of the fan; — the power input of all control and safety devices of the equipment Note 1 to entry
PE is expressed in watts. 3.6 reference air volume flow qvref airflow at 70 % of qvd Note 1 to entry: If the unit’s air volume flow cannot be adjusted to reach (qvref, ptUd/2), the closest value above 70 % is selected. Note 2 to entry: qvref is expressed in m3„s−1 or l„s−1. 3.7 fan pressure pF pressure increase induced by the fan given as the difference of outlet and inlet total pressure Note 1 to entry: pF is expressed in Pa. [Source: EN 13141-4:2011, definition 3.1 with expression of the unit modified] 3.8 declared total pressure ptUd pressure used to set the maximum air volume flow corresponding to 100 Pa, or to a lower total pressure if the intended use declared by the manufacturer is less than 100 Pa Note 1 to entry: ptUd is expressed in Pa. 3.9 habitable room room used for purposes such as living rooms, bedrooms or study rooms 3.10 wet room room used for domestic activities such as kitchens, utility rooms, bathrooms or sanitary accommodation SIST EN 13141-11:2015



EN 13141-11:2015 (E) 9 4 Symbols and abbreviations For the purposes of this document, the symbols and abbreviations given in EN 12792:2003 and those given in Table 1 apply. Table 1 — Symbols and abbreviations Symbol Description Unit Dn,e Sound insulation dB Dn,e,w Overall sound insulation dB Dn,e,w + Ctr Overall sound insulation for a standardized traffic noise dB qv Air volume flow m3„s−1 or l„s−1 qvd Declared maximum air volume flow m3„s−1 or l„s−1 qve External leakage air volume flow m3„s−1 or l„s−1 qvref Reference air volume flow m3„s−1 or l„s−1 LW Sound power level dB LWA A-weighted sound power level dB(A) LWglobalN Global sound power level of the N identical duct connection dB LWsingle Sound power level of a single duct dB N Number of identical duct connections — PE Electrical power input W pF Fan pressure Pa ptU Total pressure (difference between outlet and inlet) of the unit Pa ptUd Declared total pressure Pa 5 Declaration of intended use The intended use of product shall be declared as follows: — for single room application where one unit is required for each habitable room see Figure A.1; — for single unit providing centralised whole dwelling ventilation see Figure A.2 or Figure A.3. 6 Performance testing of aerodynamic characteristics 6.1 General A fan is specified to supply a given flow rate to an installation. In order to choose the appropriate fan, it is necessary to know its performance characteristics, given as the volume flow rate as a function of fan pressure. These characteristics are strongly influenced by upstream flow conditions (velocity profile, possible presence of a swirl and wind). Downstream conditions do not usually affect the fan operation, but the nature of flow downstream from the fan, especially the swirl, can have an effect on pressure losses in the circuit and should be taken into account during installation design. The four following categories of installations are defined in EN ISO 5801: SIST EN 13141-11:2015



EN 13141-11:2015 (E) 10 — category A: free inlet and free outlet; — category B: free inlet and ducted outlet; — category C: ducted inlet and free outlet; — category D: ducted inlet and ducted outlet. For each category, EN ISO 5801 defines the installation in the immediate proximity of the fan, as well as the position of the pressure measurement. Test installation and conditions are described in EN 13141-4. 6.2 External leakage Pressure method applies to classify external leakage by using Table 2. External leakage tests shall only be applied to products intended to be connected in a category C or category D configuration. Table 2 — External leakage classification – pressure method Class Pressurization test External leakage Centralised unit for whole dwelling Single Room (at 150 Paa) (at 50 Paa) % % A1 ≤ 2 ≤ 2 A2 ≤ 5 ≤ 5 A3 ≤ 10 ≤ 10 not classified > 10 > 10 a Pressure at which the external leakage test is performed at. This test pressure depends on the type of unit tested. The external leakage shall be measured according to Annex D. The external leakage air volume flow qve at over and/or under pressure, according to Table 2, shall be measured and reported as such and also compared to the declared maximum air volume flow of the unit as a percentage. If all components (filters, battery, etc.) are situated: — upstream of the fan, the external leakage should be measured under pressure; — downstream of the fan, the external leakage shall be measured in over pressure; — on either side of the fan, the external leakage shall be measured in over and under pressure. During the pressurization tests for external leakage, the fan of the unit under tes
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.