SIST EN 4710-007:2015
(Main)Aerospace series - Quick release fastening systems for non-structural applications - Part 007: Retaining grommet
Aerospace series - Quick release fastening systems for non-structural applications - Part 007: Retaining grommet
This European Standard specifies the dimensions, mass and tolerances of the retaining grommet for use
in fuselage interior equipment and non-structural or secondary structural area.
This European Standard is to be used in conjunction with EN 4710-06 as described in EN 4710-02.
The applicable temperature range is -55 °C to 85 °C.
Luft- und Raumfahrt - Druckverschlüsse nicht-strukturelle Anwendunge - Teil 007: Haltering
Diese Europäische Norm legt die Maße, Massen, und Toleranzen von Halteringen fest, die bei der Inneneinrichtung von Luftfahrzeugen und in nicht-strukturellen oder Sekundärstrukturbereichen verwendet werden.
Diese Europäische Norm ist in Verbindung mit EN 4710-06 wie in EN 4710-02 beschrieben anzuwenden.
Der gültige Temperaturbereich ist zwischen −55 °C und 85 °C.
Série aérospatiale - Fixations rapides filetées pour applications non-structurales - Partie 007 : Œillet de retenue
La présente Norme européenne spécifie les dimensions, la masse et les tolérances des oeillets de retenue pour utilisation dans les équipements intérieurs et dans les zones non structurales ou structurales secondaires du fuselage.
La présente Norme européenne doit être utilisée conjointement avec l’EN 4710-06 comme défini dans l’EN 4710-02.
La gamme de température applicable est comprise entre - 55 °C et 85 °C.
Aeronavtika - Spončni sistemi za hitro sprostitev za nestrukturne aplikacije - 007. del: Držalni obroček
Ta evropski standard določa dimenzije, maso in tolerance držalnega obročka za uporabo v notranji opremi v trupu letala ter nestrukturnem ali sekundarnem strukturnem območju. Ta evropski standard je treba uporabljati v povezavi s standardom EN 4710-06, kot je opisano v standardu EN 4710-02. Delovna temperatura je med –55 °C in 85 °C.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Druckverschlüsse nicht-strukturelle Anwendunge - Teil 007: HalteringSérie aérospatiale - Fixations rapides filetées pour applications non-structurales - Partie 007 : Œillet de retenueAerospace series - Quick release fastening systems for non-structural applications - Part 007: Retaining grommet49.030.01Vezni elementi na splošnoFasteners in generalICS:Ta slovenski standard je istoveten z:EN 4710-07:2015SIST EN 4710-007:2015en,fr,de01-december-2015SIST EN 4710-007:2015SLOVENSKI
STANDARD
SIST EN 4710-007:2015
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4710-07
October
t r s w ICS
v {ä r u w English Version
Aerospace series æ Quick release fastening systems for nonæstructural applications æ Part
r yã Retaining grommetSérie aérospatiale æ Fixations rapides filetées pour applications nonæstructurales æ Partie
r y ã Oeillet de retenue
Luftæ und Raumfahrt æ Schnellverschlüsse für nichtæstrukturelle Anwendungen æ Teil
r yã Haltering This European Standard was approved by CEN on
w March
t r s wä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey andUnited Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s w CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
v y s ræ r yã t r s w ESIST EN 4710-007:2015
EN 4710-07:2015 (E) 2 Contents
Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Requirements . 5 4 Designation. 6 5 Marking . 6 6 Technical specification . 7
SIST EN 4710-007:2015
EN 4710-07:2015 (E) 3 European foreword This document (EN 4710-07:2015) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this European Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2016, and confl
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.