SIST EN ISO 505:2018
(Main)Conveyor belts - Method for the determination of the tear propagation resistance of textile conveyor belts (ISO 505:2017)
Conveyor belts - Method for the determination of the tear propagation resistance of textile conveyor belts (ISO 505:2017)
This document specifies a method of test for the measurement of the propagation resistance of an initial
tear in textile conveyor belts, either in full thickness or of the carcass only.
This test is intended for application to textile belts in installations where there is a risk of longitudinal
tearing.
Fördergurte - Verfahren zur Bestimmung der Weiterreißfestigkeit von Textil-Fördergurten (ISO 505:2017)
Dieses Dokument legt ein Verfahren zur Messung der Weiterreißfestigkeit an Textil-Fördergurten fest, die mit einem Einschnitt versehen wurden, entweder in voller Dicke des Fördergurtes oder nur in der Karkasse.
Diese Prüfung gilt für Textil-Fördergurte, die zum Einsatz in Anlagen vorgesehen sind, bei denen die Gefahr des Reißens des Gurtes in Längsrichtung besteht.
Courroies transporteuses - Méthode de détermination de la résistance à la propagation d'une déchirure dans les courroies transporteuses à carcasse textile (ISO 505:2017)
L'ISO 505 :2017 spécifie une méthode d'essai pour le mesurage de la résistance à la propagation d'une déchirure préalablement amorcée des courroies transporteuses à carcasse textile, soit en pleine épaisseur soit dans la carcasse seule.
Cet essai est destiné à être appliqué aux courroies textiles utilisées dans les installations pour lesquelles il existe un risque de déchirement longitudinal.
Naprave za kontinuirni transport - Trakovi tračnih transporterjev - Postopek določanja odpornosti proti vzdolžnemu trganju tekstilnih trakov tračnih transporterjev (ISO 505:2017)
Ta dokument določa metodo preskušanja za merjenje odpornosti na širjenje začetne raztrganine v tekstilnih transportnih trakovih, bodisi po celotni debelini ali zgolj v ogrodju.
Ta preskus je namenjen uporabi v tekstilnih trakovih in napravah, kjer obstaja nevarnost raztrganja po dolžini.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 505:2018
01-maj-2018
1DGRPHãþD
SIST EN ISO 505:2001
1DSUDYH]DNRQWLQXLUQLWUDQVSRUW7UDNRYLWUDþQLKWUDQVSRUWHUMHY3RVWRSHN
GRORþDQMDRGSRUQRVWLSURWLY]GROåQHPXWUJDQMXWHNVWLOQLKWUDNRYWUDþQLK
WUDQVSRUWHUMHY ,62
Conveyor belts - Method for the determination of the tear propagation resistance of
textile conveyor belts (ISO 505:2017)
Fördergurte - Verfahren zur Bestimmung der Weiterreißfestigkeit von Textil-Fördergurten
(ISO 505:2017)
Courroies transporteuses - Méthode de détermination de la résistance à la propagation
d'une déchirure dans les courroies transporteuses à carcasse textile (ISO 505:2017)
Ta slovenski standard je istoveten z: EN ISO 505:2017
ICS:
53.040.20 Deli za transporterje Components for conveyors
SIST EN ISO 505:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 505:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 505:2018
EN ISO 505
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2017
EUROPÄISCHE NORM
ICS 53.040.20 Supersedes EN ISO 505:1999
English Version
Conveyor belts - Method for the determination of the tear
propagation resistance of textile conveyor belts (ISO
505:2017)
Courroies transporteuses - Méthode de détermination Fördergurte - Verfahren zur Bestimmung der
de la résistance à la propagation d'une déchirure dans Weiterreißfestigkeit von Textil-Fördergurten (ISO
les courroies transporteuses à carcasse textile (ISO 505:2017)
505:2017)
This European Standard was approved by CEN on 17 November 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 505:2017 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 505:2018
EN ISO 505:2017 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 505:2018
EN ISO 505:2017 (E)
European foreword
This document (EN ISO 505:2017) has been prepared by Technical Committee ISO/TC 41 “Pulleys and
belts (including veebelts)” in collaboration with Technical Committee CEN/TC 188 “Conveyor belts” the
secretariat of which is held by SNV.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2018, and conflicting national standards shall be
withdrawn at the latest by June 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 505:1999.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 505:2017 has been approved by CEN as EN ISO 505:2017 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 505:2018
---------------------- Page: 6 ----------------------
SIST EN ISO 505:2018
INTERNATIONAL ISO
STANDARD 505
Fourth edition
2017-10
Conveyor belts — Method for the
determination of the tear propagation
resistance of textile conveyor belts
Courroies transporteuses — Méthode de détermination de la
résistance à la propagation d'une déchirure dans les courroies
transporteuses à carcasse textile
Reference number
ISO 505:2017(E)
©
ISO 2017
---------------------- Page: 7 ----------------------
SIST EN ISO 505:2018
ISO 505:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 505:2018
ISO 505:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
6 Test pieces . 2
6.1 Method of sampling . 2
6.2 Shape and dimensions . 2
6.3 Number . 2
6.4 Preparation . 2
7 Method of test . 4
7.1 Conditioning of test pieces . 4
7.2 Test conditions . 4
7.3 Procedure .
...
SLOVENSKI STANDARD
oSIST prEN ISO 505:2017
01-julij-2017
1DSUDYH]DNRQWLQXLUQLWUDQVSRUW7UDNRYLWUDþQLKWUDQVSRUWHUMHY3RVWRSHN
GRORþDQMDRGSRUQRVWLSURWLY]GROåQHPXWUJDQMXWHNVWLOQLKWUDNRYWUDþQLK
WUDQVSRUWHUMHY ,62)',6
Conveyor belts - Method for the determination of the tear propagation resistance of
textile conveyor belts (ISO/FDIS 505:2017)
Fördergurte - Verfahren zur Bestimmung der Weiterreißfestigkeit von Textil-Fördergurten
(ISO/FDIS 505:2017)
Courroies transporteuses - Méthode de détermination de la résistance à la propagation
d'une déchirure dans les courroies transporteuses à carcasse textile (ISO/FDIS
505:2017)
Ta slovenski standard je istoveten z: prEN ISO 505
ICS:
53.040.20 Deli za transporterje Components for conveyors
oSIST prEN ISO 505:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 505:2017
---------------------- Page: 2 ----------------------
oSIST prEN ISO 505:2017
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 505
ISO/TC 41/SC 3
Conveyor belts — Method for the
Secretariat: JISC
determination of the tear propagation
Voting begins on:
20170518 resistance of textile conveyor belts
Voting terminates on:
Courroies transporteuses — Méthode de détermination de la
20170810
résistance à la propagation d’une déchirure dans les courroies
transporteuses à carcasse textile
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/FDIS 505:2017(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2017
---------------------- Page: 3 ----------------------
oSIST prEN ISO 505:2017
ISO/FDIS 505:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 505:2017
ISO/FDIS 505:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
6 Test pieces . 2
6.1 Method of sampling . 2
6.2 Shape and dimensions . 2
6.3 Number . 2
6.4 Preparation . 2
7 Method of test . 4
7.1 Conditioning of test pieces . 4
7.2 Test conditions . 4
7.3 Procedure . 4
7.4 Expression of results . 5
7.5 Test report . 5
© ISO 2017 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 505:2017
ISO/FDIS 505:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and nongovernmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.