SIST EN 10152:2017
(Main)Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions
Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions
This European Standard specifies requirements for continuously electrolytic zinc coated cold rolled flat products of low carbon steels suitable for cold forming according to Table 1 in rolled widths above or equal to 600 mm and thicknesses from 0,35 mm up to and including 3 mm, delivered as strip (in coil form), sheet, slit strip or cut lengths obtained from slit strip or sheet.
NOTE 1 This European Standard can also be applied to continuously electrolytic zinc coated flat products of:
a) steels according to EN 10139 (cold rolled strip in rolled widths < 600 mm),
b) steels normally characterized by minimum yield strength or minimum tensile strength values in addition to formability parameters, e. g. 1) steels with high yield strength and improved formability according to EN 10268 (cold rolled flat products), 2) multiphase steels (cold rolled or hot rolled) according to prEN 10338, 3) steels for construction according to national or regional standards (see e. g. DIN 1623).
NOTE 2 By agreement at the time of enquiry and order this European Standard can be applied to continuously electrolytic zinc coated hot-rolled steel flat products (e.g. according to EN 10025-1 and -2, EN 10111, EN 10149-1 to EN 10149-3, etc.).
NOTE 3 As the mass of the zinc coating applied is relatively small, the material is not intended to withstand outside exposure without further chemical treatment and painting.
Elektrolytisch verzinkte kaltgewalzte Flacherzeugnisse aus Stahl zum Kaltumformen - Technische Lieferbedingungen
Produits plats en acier, laminés à froid, revêtus de zinc par voie électrolytique pour formage à froid - Conditions techniques de livraison
La présente Norme européenne définit les prescriptions relatives aux produits plats laminés à froid revêtus de zinc en continu par voie électrolytique (ou produit par un autre procédé sur un support laminé à froid), en aciers à bas carbone aptes au formage à froid selon les indications du Tableau 1, en largeurs laminées ≥ 600 mm et en épaisseurs comprises entre 0,35 mm et 3 mm inclus, livrés sous forme de bandes (en bobines), de tôles, de bandes refendues coupées à longueur ou non ou dans des tôles.
NOTE 1 La présente Norme européenne peut également s'appliquer aux produits plats revêtus de zinc en continu, par voie électrolytique, en :
a) aciers conformes à l'EN 10139 (feuillards laminés à froid en largeurs de laminage < 600 mm),
b) aciers normalement caractérisés par une valeur minimale de limite d'élasticité ou de résistance à la traction en plus de leur aptitude au formage et par exemple ;
1) aciers à haute limite d'élasticité et à formabilité améliorée conformes à l’EN 10268 (produits plats laminés à froid) ;
2) aciers multiphasés (laminés à froid ou laminés à chaud) conformes au EN 10338 ;
3) aciers pour la construction conformes aux normes nationales ou régionales (voir par exemple DIN 1623).
NOTE 2 Par accord au moment de l’appel d’offres et à la commande, cette Norme européenne peut être appliquée aux produits plats laminés à chaud revêtus de zinc en continu par voie électrolytique (par exemple, conforme aux normes EN 10025-1 et -2, EN 10111, EN 10149-1 à EN 10149-3, etc.).
NOTE 3 Comme la masse du revêtement de zinc appliqué est relativement faible, le matériau n'est pas censé résister à une exposition extérieure sans traitement chimique supplémentaire et application de peinture.
NOTE 4 Les produits conforme à cette norme européenne peuvent être utilisés comme substrats pour les produits plats à revêtement organique spécifiés dans l'EN 10169 pour des applications dans la construction et la mécanique générale.
Elektrolizno cinkani hladno valjani ploščati izdelki iz jekla za hladno preoblikovanje - Tehnični dobavni pogoji
Ta evropski standard določa zahteve za trajno elektrolizno cinkane hladno valjane ploščate izdelke iz jekla z nizko vsebnostjo ogljika, primerne za hladno preoblikovanje v skladu s preglednico 1, z valjano širino vsaj 600 mm in debelino od 0,35 mm do vključno 3 mm, dobavljene v obliki traka (zvitki), pločevine, razrezanega traka ali narezanih dolžin iz razrezanega traka oziroma pločevine. OPOMBA 1: Ta evropski standard se lahko uporablja tudi za trajno elektrolizno cinkane ploščate izdelke iz: a) jekla v skladu s standardom EN 10139 (hladno valjan trak v valjanih širinah < 600 mm), b) jekla, ki ga poleg parametrov oblikovalnosti običajno opredeljujejo najmanjše vrednosti meje tečenja ali natezne trdnosti, npr. 1) jekla z visoko mejo tečenja in izboljšano oblikovalnostjo v skladu s standardom EN 10268 (hladno valjani ploščati izdelki), 2) večfazna jekla (hladno valjana ali vroče valjana) v skladu s standardom prEN 10338, 3) jekla za gradnjo v skladu z nacionalnimi ali regionalnimi standardi (glej npr. DIN 1623). OPOMBA 2: Ta evropski standard je mogoče po dogovoru v času povpraševanja in naročila uporabiti za trajno elektrolizno cinkane vroče valjane ploščate izdelke (npr. v skladu s standardi EN 10025-1 in -2, EN 10111, EN 10149-1 do EN 10149-3 itd.). OPOMBA 3: Ker je masa nanesenega cinkovega premaza sorazmerno majhna, material ni namenjen za uporabo na prostem brez dodatne kemične obdelave in barvanja.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.KODGQRElektrolytisch verzinkte kaltgewalzte Flacherzeugnisse aus Stahl zum Kaltumformen - Technische LieferbedingungenProduits plats en acier, laminés à froid, revêtus de zinc par voie électrolytique pour formage à froid - Conditions techniques de livraisonElectrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery conditions77.140.50SROL]GHONLFlat steel products and semi-productsICS:Ta slovenski standard je istoveten z:EN 10152:2017SIST EN 10152:2017en,fr,de01-april-2017SIST EN 10152:2017SLOVENSKI
STANDARDSIST EN 10152:2009/AC:2012SIST EN 10152:20091DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10152
January
t r s y ICS
y yä s v rä w r Supersedes EN
s r s w tã t r r {English Version
Electrolytically zinc coated cold rolled steel flat products for cold forming æ Technical delivery conditions Produits plats en acierá laminés à froidá revêtus de zinc par voie électrolytique pour formage à froid æ Conditions techniques de livraison
Elektrolytisch verzinkte kaltgewalzte Flacherzeugnisse aus Stahl zum Kaltumformen æ Technische Lieferbedingungen This European Standard was approved by CEN on
t s November
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s r s w tã t r s y ESIST EN 10152:2017
Reference method for determination of the zinc coating mass . 18 A.1 Principle . 18 A.2 Reagent and preparation of the solution . 18 A.2.1 Reagent . 18 A.2.2 Preparation of the solution . 18 A.3 Apparatus . 18 A.4 Procedure . 18 Bibliography . 19
· 600 mm and thicknesses from 0,35 mm up to below and including 3 mm, delivered as strip (in coil form), sheet, slit strip or cut lengths obtained from slit strip or sheet. NOTE 1 This European Standard can also be applied to continuously electrolytic zinc coated flat products of: a) steels according to EN 10139 (cold rolled strip in rolled widths < 600 mm), b) steels normally characterized by minimum yield strength or minimum tensile strength values in addition to formability parameters, e.g. 1) steels with high yield strength and improved formability according to EN 10268 (cold rolled flat products), 2) multiphase steels (cold rolled or hot rolled) according to EN 10338, 3) steels for construction according to national or regional standards (see e.g. DIN 1623). NOTE 2 By agreement at the time of enquiry and order this European Standard can be applied to continuously electrolytic zinc coated hot-rolled steel flat products (e.g. according to EN 10025–1 and
« tá EN 10111, EN 10149–1 to EN 10149–3, etc.). NOTE 3 As the mass of the zinc coating applied is relatively small, the material is not intended to withstand outside exposure without further chemical treatment and painting. NOTE 4 The products covered by this European Standard can be used as substrates for organic coated flat products specified in EN 10169 for building and general engineering applications. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10020:2000, Definition and classification of grades of steel EN 10021:2006, General technical delivery conditions for steel products EN 10027-1, Designation systems for steels - Part 1: Steel names EN 10027-2, Designation systems for steels - Part 2: Numerical system EN 10051, Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape EN 10079:2007, Definition of steel products EN 10131, Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimensions and shape SIST EN 10152:2017
electrolytic zinc coating (ZE) application of a zinc coating by electrolysis on a suitably prepared steel surface from an aqueous zinc salt solution by the use of an electric current Note 1 to entry
Flat products can have a zinc coating on one or both surfaces. If both surfaces are zinc coated, a different coating thickness can be applied on each side (this process being referred to as differential zinc coating). 4 Classification and designation 4.1 Classification The steel grades specified in this European Standard are classified in accordance with EN 10020:2000 as non-alloy quality steels (DC01, DC03, DC04, DC05) and alloy quality steels (DC06, DC07) and by their increasing suitability for cold forming as follows: — DC01: drawing quality; — DC03: deep drawing quality; — DC04, DC05: special deep drawing quality; — DC06: extra deep drawing quality; — DC07: super deep drawing quality. 4.2 Designation 4.2.1 The steel names are allocated in accordance with EN 10027-1. The steel numbers are allocated in accordance with EN 10027-2. 4.2.2 The products covered by this document shall be designated as follows in the given order: 1) Type of product (e.g. strip, sheet, cut length); 2) Number of this European Standard (EN 10152); 3) Steel name or steel number and symbol for the type of electrolytic coating (see Table 1); SIST EN 10152:2017
Strip EN 10152 —+ZE50 DC03/50-A-P or Strip EN 10152–1.0347+ZE50/50-A-P EXAMPLE 2 Designation of sheet made of steel DC05+ZE (1.0312+ZE), electrolytically zinc coated with a nominal thickness of 7,5
treatment phosphated and oiled (PO): Sheet EN 10152 —+ZE75 DC05/25-B-PO or Sheet EN 10152–1.0312+ZE75/25-B-PO 4.2.3 Where appropriate, additional information to the designation as specified in 4.2.2 shall be given to describe clearly the delivery requirements (see Clause 5). 5 Information to be supplied by the purchaser 5.1 Mandatory information The following information shall be supplied by the purchaser at the time of enquiry and order: a) complete designation (see 4.2.2); b) nominal dimensions (thickness, width and, in the case of sheet and cut lengths, length); c) quantity; d) limiting mass and sizes of the coils and individual bundles of sheets; e) surface quality and surface finish (see 6.10); f) type of surface treatment (see 6.11 and Table 3). SIST EN 10152:2017
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...