SIST EN 50059:2025
(Main)Hand-held electrostatic application equipment for non-ignitable liquid coating materials - Safety requirements
Hand-held electrostatic application equipment for non-ignitable liquid coating materials - Safety requirements
1.1 This document specifies the requirements for hand-held or hand-operated electrostatic spraying equipment for non-ignitable liquid coating materials which
— do not generate an explosive atmosphere inside the spraying area,
— are used to process materials with a conductivity of less than 2 000 µS/cm, and
— operate with direct current having a sinusoidal ripple of not more than 10 % of the rms value.
This document deals with all electrical hazards significant for the electrostatic spraying of non-ignitable liquid coating materials, which could also contain small quantities of added metal particles, if the work is carried out under conditions recommended by the manufacturer.
This document specifies the design-related and test requirements for electrostatic spraying equipment of type A-NL according to of EN 50348:2010, Table 1.
1.2 With regard to all other significant hazards relevant for applicators (e.g. ejection of fluids, mechanical strength, electrical (with the exception of electrostatic) hazards, noise, contact with or inhalation of dangerous substances, ergonomics), the requirements of EN 1953 apply.
1.3 This document also gives details regarding quality assurance systems for electrostatic spraying equipment; see Annex D.
1.4 For electrostatic spraying equipment used in food and pharmaceutical industry, additional requirements could apply.
1.5 This document is not applicable to:
— electrostatic hand-held spraying equipment for non-ignitable coating materials which are manufactured before the date of its publication,
— cleaning of spraying areas, see instruction manual of the spraying booth,
— fire prevention and protection (for instance fire hazards due to other sources; see EN 16985),
— requirements for machinery for the supply and recirculation of coating material under pressure (see EN 12621).
The requirements of EN 12621 apply in terms of specific requirements regarding machinery for the supply and recirculation of coating materials under pressure.
Elektrostatische Handsprüheinrichtungen - Sicherheitsanforderungen - Handsprüheinrichtungen für nichtentzündbare Beschichtungsstoffe
Équipement manuel d’application électrostatique de produits de revêtement liquides non-inflammables - Exigences de sécurité
1.1 Le présent document spécifie les exigences relatives aux équipements portatifs ou manuels de projection électrostatique de produits liquides de revêtement ininflammables qui
— ne génèrent pas d'atmosphère explosive au sein de l'emplacement de projection,
— sont utilisés pour traiter les matériaux ayant une conductivité inférieure à 2 000 µS/cm, et
— fonctionnent en courant continu avec une ondulation sinusoïdale inférieure ou égale à 10 % de la valeur efficace.
Le présent document traite de tous les dangers électriques importants concernant la projection électrostatique de produits liquides de revêtement ininflammables pouvant également comporter de petites quantités de particules de métal supplémentaires, si la tâche est réalisée dans les conditions recommandées par le fabricant.
Le présent document spécifie les exigences relatives à la conception et les exigences d'essai des équipements de projection électrostatique de type A-NL, conformément à l'EN 50348:2010, Tableau 1.
1.2 Les exigences de l'EN 1953 s'appliquent pour tous les autres dangers significatifs concernant les applicateurs (par exemple, éjection de fluides, résistance mécanique, dangers électriques (à l’exception des dangers électrostatiques), bruit, contact avec ou inhalation des substances dangereuses, ergonomie).
1.3 Le présent document fournit également des informations détaillées concernant les systèmes d'assurance qualité des équipements de projection électrostatique, voir l'Annexe D.
1.4 Pour les équipements de projection électrostatique utilisés dans l'industrie alimentaire et dans l'industrie pharmaceutique, des exigences supplémentaires peuvent s'appliquer.
1.5 Le présent document ne s'applique pas:
— aux équipements portatifs de projection électrostatique de revêtement ininflammable fabriqués avant sa date de publication,
— au nettoyage des emplacements de projection, voir le manuel d'instructions de la cabine de projection,
— à la prévention et la protection contre le feu (par exemple, dangers d'incendie dus à d’autres sources; voir l'EN 16985),
— aux exigences relatives aux machines d'alimentation et de circulation de produits de revêtement sous pression (voir l'EN 12621).
Les exigences de l'EN 12621 s'appliquent aux exigences spécifiques concernant les machines d'alimentation et de circulation de produits de revêtement sous pression.
Ročna elektrostatična oprema za brizganje nevnetljivih tekočih premazov - Varnostne zahteve
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2025
Ročna elektrostatična oprema za brizganje nevnetljivih tekočih premazov -
Varnostne zahteve
Hand-held electrostatic application equipment for non-ignitable liquid coating materials -
Safety requirements
Elektrostatische Handsprüheinrichtungen - Sicherheitsanforderungen -
Handsprüheinrichtungen für nichtentzündbare Beschichtungsstoffe
Équipement manuel d’application électrostatique de produits de revêtement liquides non-
inflammables - Exigences de sécurité
Ta slovenski standard je istoveten z: EN 50059:2025
ICS:
87.100 Oprema za nanašanje Paint coating equipment
premazov
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 50059
NORME EUROPÉENNE
EUROPÄISCHE NORM February 2025
ICS 87.100 Supersedes EN 50059:2018
English Version
Hand-held electrostatic application equipment for non-ignitable
liquid coating materials - Safety requirements
Équipement manuel d'application électrostatique de Elektrostatische Handsprüheinrichtungen -
produits de revêtement liquides non-inflammables - Sicherheitsanforderungen - Handsprüheinrichtungen für
Exigences de sécurité nichtentzündbare Beschichtungsstoffe
This European Standard was approved by CENELEC on 2024-12-30. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50059:2025 E
Contents Page
European foreword .4
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms, definitions and symbols .7
3.1 Terms and definitions .7
3.2 List of symbols . 10
4 Electric hazards . 10
5 Requirements for application equipment . 10
5.1 Prevention of electric shock . 10
5.1.1 General . 10
5.1.2 Electrical safety. 10
5.1.3 Bonding to earth potential . 11
5.1.4 Cables under high voltage . 11
5.1.5 Undercutting the limits of electric shock . 11
5.1.6 Limiting parts . 12
5.2 Additional requirements for the applicator . 13
5.2.1 General . 13
5.2.2 Resistance against impact . 13
5.2.3 Resistance against dropping . 13
5.2.4 Reliability . 13
5.2.5 Handle . 13
5.2.6 Trigger . 13
5.3 Additional requirements for the coating material supply system . 13
5.3.1 General . 13
5.3.2 Hoses of the coating material supply under high voltage. 14
5.3.3 Other insulating parts under high voltage . 14
5.3.4 Conductive and dissipative parts . 14
5.4 Requirements for the control system . 14
5.4.1 General . 14
5.4.2 IP protection . 14
5.4.3 Interface . 14
6 Tests (type tests) . 14
6.1 Test of prevention of electric shock . 14
6.1.1 General . 14
6.1.2 Test of electrical safety . 15
6.1.3 Test of bonding to earth potential . 15
6.1.4 Test of cables under high voltage . 15
6.1.5 Undercutting the limits of electric shock . 15
6.1.6 Test of limiting parts . 15
6.2 Test of additional requirements for the applicator . 15
6.2.1 General . 15
6.2.2 Impact test . 15
6.2.3 Drop test . 16
6.2.4 Test of reliability . 16
6.2.5 Test of the handle . 16
6.2.6 Test of trigger . 16
6.3 Test of additional requirements for the coating material supply system . 16
6.3.1 General . 16
6.3.2 Test of the coating material supply hose under high voltage . 16
6.3.3 Test of other insulating parts under high voltage. 17
6.3.4 Test of conductive and dissipative parts . 17
6.4 Test of additional requirements for the control system . 17
6.4.1 General . 17
6.4.2 Test of the degree of protection . 17
6.4.3 Interface . 17
7 Information for use . 17
7.1 General . 17
7.2 Instruction for use . 17
7.2.1 General . 17
7.2.2 Information on installation . 18
7.2.3 Information on operation . 18
7.2.4 Cleaning, maintenance, and corrective maintenance . 19
7.2.5 Periodic inspections . 19
7.3 Marking of application equipment . 19
7.3.1 Marking of applicators . 19
7.3.2 Marking of the control system . 20
7.3.3 Multiple marking of the control system . 20
Annex A (normative) Compliance with area I for application equipment including parts of the
coating material supply system . 21
Annex B (informative) Example for discharge measurement . 27
Annex C (informative) Ignitability of liquid coating materials . 29
Annex ZZ (informative) Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered . 30
Bibliography . 32
European foreword
This document (EN 50059:2025) has been prepared by CLC/TC 204 “Safety of electrostatic painting and
finishing equipment”.
The following dates are fixed:
• latest date by which this document has to be (dop) 2026-02-28
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) 2028-02-29
conflicting with this document have to be
withdrawn
This document supersedes EN 50059:2018 and all of its amendments and corrigen
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.