SIST EN ISO 10350-1:2008

SLOVENSKI STANDARD
SIST EN ISO 10350-1:2008
01-november-2008
1DGRPHãþD
SIST EN ISO 10350-1:2001
3ROLPHUQLPDWHULDOL3ULGRELWHYLQSUHGVWDYLWHYSULPHUOMLYLK]QDþLOQLKHQRWRþNRYQLK
SRGDWNRYGHO0DWHULDOL]DREOLNRYDQMD,62
Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding
materials (ISO 10350-1:2007)
Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte - Teil 1:
Formmassen (ISO 10350-1:2007)
Plastiques - Acquisition et présentation de caractéristiques intrinsèques comparables -
Partie 1: Matériaux pour moulage (ISO 10350-1:2007)
Ta slovenski standard je istoveten z: EN ISO 10350-1:2008
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 10350-1:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 10350-1:2008

---------------------- Page: 2 ----------------------

SIST EN ISO 10350-1:2008
EUROPEAN STANDARD
EN ISO 10350-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2008
ICS 83.080.20 Supersedes EN ISO 10350-1:2000
English Version
Plastics - Acquisition and presentation of comparable single-
point data - Part 1: Moulding materials (ISO 10350-1:2007)
Plastiques - Acquisition et présentation de caractéristiques Kunststoffe - Ermittlung und Darstellung vergleichbarer
intrinsèques comparables - Partie 1: Matériaux pour Einpunktkennwerte - Teil 1: Formmassen (ISO 10350-
moulage (ISO 10350-1:2007) 1:2007)
This European Standard was approved by CEN on 30 July 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10350-1:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 10350-1:2008
EN ISO 10350-1:2008 (E)
Contents Page
Foreword.3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 10350-1:2008
EN ISO 10350-1:2008 (E)
Foreword
The text of ISO 10350-1:2007 has been prepared by Technical Committee ISO/TC 61 “Plastics” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 10350-1:2008 by
Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by February 2009, and conflicting national standards shall be withdrawn
at the latest by February 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10350-1:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10350-1:2007 has been approved by CEN as a EN ISO 10350-1:2008 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 10350-1:2008

---------------------- Page: 6 ----------------------

SIST EN ISO 10350-1:2008

INTERNATIONAL ISO
STANDARD 10350-1
Second edition
2007-07-15

Plastics — Acquisition and presentation
of comparable single-point data —
Part 1:
Moulding materials
Plastiques — Acquisition et présentation de caractéristiques
intrinsèques comparables —
Partie 1: Matériaux pour moulage




Reference number
ISO 10350-1:2007(E)
©
ISO 2007
.

---------------------- Page: 7 ----------------------

SIST EN ISO 10350-1:2008
ISO 10350-1:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2007 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 10350-1:2008
ISO 10350-1:2007(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 3
4 Specimen preparation and conditioning. 3
5 Test requirements. 4
6 Presentation of results. 4

© ISO 2007 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 10350-1:2008
ISO 10350-1:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10350-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 2, Mechanical
properties.
This second edition cancels and replaces the first edition (ISO 10350-1:1998), which has been technically
revised.
ISO 10350 consists of the following parts, under the general title Plastics — Acquisition and presentation of
comparable single-point data:
⎯ Part 1: Moulding materials
⎯ Part 2: Long-fibre-reinforced plastics
iv © ISO 2007 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 10350-1:2008
ISO 10350-1:2007(E)
Introduction
ISO 10350 has been prepared because users of plastics find that available data cannot always be readily
used to compare the properties of similar materials, especially when the data have been supplied by different
sources. Even when the same standard tests have been used, they often allow the adoption of a wide range
of alternative test conditions, and the data obtained are not necessarily comparable. The purpose of this
International Standard is to identify specific methods and conditions of test to be used for the acquisition and
presentation of data in order that valid comparisons between materials can be made.
ISO 10350 is concerned with tests employed to present “single-point” data on the limited range of properties
commonly included in data sheets and used for the preliminary selection of materials. Such data represent the
most basic approach to the specification of properties of materials, and the standard thus facilitates the first
steps towards more efficient selection and use of plastics in the many applications to which they are suited.
1)
Complementary International Standards (ISO 11403-1, ISO 11403-2 and ISO 11403-3) are concerned with
the standardized acquisition and presentation of multipoint data, to demonstrate how properties vary with
important factors such as time, temperature and the presence of particular natural and chemical environments.
In these standards, some additional properties are included. Their use will provide a more substantial
database than one containing only single-point data, and so will enable improved assessment of the fitness of
a material for any particular application. In addition, ISO 11403-1, which deals with mechanical properties,
assists predictions of the performance of components and ISO 11403-2, covering thermal and processing
properties, aids predictions of melt-flow behaviour during manufacturing. ISO 11403-3 is concerned with
environmental influences on properties, and other parts may be prepared to cover additional properties.


1) ISO 11403-1, Plastics — Acquisition and presentation of comparable multipoint data — Part 1: Mechanical properties
ISO 11403-2, Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and
processing properties
ISO 11403-3, Plastics — Acquisition and presentation of comparable multipoint data — Part 3: Environmental
influences on properties
© ISO 2007 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 10350-1:2008

---------------------- Page: 12 ----------------------

SIST EN ISO 10350-1:2008
INTERNATIONAL STANDARD ISO 10350-1:2007(E)

Plastics — Acquisition and presentation of comparable single-
point data —
Part 1:
Moulding materials
1 Scope
ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for
certain basic properties of plastics. In general, each property is specified by a single experimental value,
although in certain cases properties are represented by two values obtained under different test conditions.
The properties included are those presented conventionally in manufacturers' data sheets. This part of
ISO 10350 applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials
that may be injection- or compression-moulded or prepared as sheets of specified thickness. Part 2 of
ISO 10350 deals specifically with long- or continuous-fibre-reinforced plastics. For the purposes of ISO 10350,
long-fibre-reinforced plastics are considered to have fibre lengths greater than 7,5 mm prior to moulding.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 62, Plastics — Determination of water absorption
ISO 75-1, Plastics — Determination of temperature of deflection under load — Part 1: General test method
ISO 75-2, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 178, Plastics — Determination of flexural properties
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 293, Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 294-1, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General
principles, and moulding of multipurpose and bar test specimens
ISO 294-3, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates
ISO 294-4, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 4:
Determination of moulding shrinkage
ISO 295, Plastics — Compression moulding of test specimens of thermosetting materials
© ISO 2007 – All rights reserved 1

---------------------- Page: 13 ----------------------

SIST EN ISO 10350-1:2008
ISO 10350-1:2007(E)
ISO 306, Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 527-1, Plastics — Determination of tensile properties — Part 1: General principles
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 899-1, Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 1133, Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of
thermoplastics
ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pyknometer method and titration method
ISO 1183-2, Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient
column method
ISO 1183-3, Plastics — Methods for determining the density of non-cellular plastics — Part 3: Gas
pyknometer method
ISO 2577, Plastics — Thermosetting moulding materials — Determination of shrinkage
ISO 2818, Plastics — Preparation of test specimens by machining
ISO 3167, Plastics — Multipurpose test specimens
ISO 4589-2, Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature
test
ISO 6603-2, Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented
impact testing
ISO 8256, Plastics — Determination of tensile-impact strength
ISO 10724-1, Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds
(PMCs) — Part 1: General principles and moulding of multipurpose test specimens
ISO 10724-2, Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds
(PMCs) — Part 2: Small plates
ISO 11357-2, Plastics — Differential scanning calorimetry (DSC) — Part 2: Determination of glass transition
temperature
ISO 11357-3, Plastics — Differential scanning calorimetry (DSC) — Part 3: Determination of temperature and
enthalpy of melting and crystallization
ISO 11359-2, Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear
thermal expansion and glass transition temperature
IEC 60093, Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
IEC 60112, Method for the determination of the proof and the comparative tracking indices of solid insulating
materials
IEC 60243-1, Electrical strength of insulating materials — Test methods — Part 1: Tests at power frequencies
IEC 60250,
...