SIST EN 60384-25-1:2007

SLOVENSKI STANDARD
SIST EN 60384-25-1:2007
01-januar-2007
Nespremenljivi kondenzatorji za elektronsko opremo - 25-1. del: Okvirna podrobna
specifikacija - Nespremenljivi aluminijevi elektrolitski kondenzatorji s prevodnim
polimernim trdim elektrolitom za površinsko montažo - Ocenjevalni nivo EZ (IEC
60384-25-1:2006)
Fixed capacitors for use in electronic equipment -- Part 25-1: Blank detail specification -
Surface mount fixed aluminium electrolytic capacitors with conductive polymer solid
electrolyte - Assessment level EZ
Festkondensatoren zur Verwendung in Geräten der Elektronik -- Teil 25-1: Vordruck für
Bauartspezifikation - Oberflächenmontierbare Aluminium-Elektrolyt-Kondensatoren mit
leitfähigem Polymerfestkörper-Elektrolyten - Bewertungsstufe EZ
Condensateurs fixes utilisés dans les équipements électroniques -- Partie 25-1:
Spécification particulière cadre - Condensateurs fixes électrolytiques en aluminium pour
montage en surface à électrolyte solide en polymère conducteur - Niveau d’assurance
de la qualité EZ
Ta slovenski standard je istoveten z: EN 60384-25-1:2006
ICS:
31.060.50 Aluminijski elektrolitni Aluminium electrolytic
kondenzatorji capacitors
SIST EN 60384-25-1:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60384-25-1:2007

---------------------- Page: 2 ----------------------

SIST EN 60384-25-1:2007


EUROPEAN STANDARD
EN 60384-25-1

NORME EUROPÉENNE
August 2006
EUROPÄISCHE NORM

ICS 31.060.40; 31.060.50

English version


Fixed capacitors for use in electronic equipment
Part 25-1: Blank detail specification –
Surface mount fixed aluminium electrolytic capacitors
with conductive polymer solid electrolyte –
Assessment level EZ
(IEC 60384-25-1:2006)


Condensateurs fixes utilisés dans  Festkondensatoren zur Verwendung
les équipements électroniques in Geräten der Elektronik
Partie 25-1: Spécification particulière Teil 25-1: Vordruck für
cadre – Bauartspezifikation –
Condensateurs fixes électrolytiques Oberflächenmontierbare
en aluminium pour montage en surface Aluminium-Elektrolyt-Kondensatoren
à électrolyte solide en polymère mit leitfähigem Polymerfestkörper-
conducteur – Elektrolyten –
Niveau d’assurance de la qualité EZ Bewertungsstufe EZ
(CEI 60384-25-1:2006) (IEC 60384-25-1:2006)


This European Standard was approved by CENELEC on 2006-07-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60384-25-1:2006 E

---------------------- Page: 3 ----------------------

SIST EN 60384-25-1:2007
EN 60384-25-1:2006 - 2 -
Foreword
The text of document 40/1734/FDIS, future edition 1 of IEC 60384-25-1, prepared by IEC TC 40,
Capacitors and resistors for electronic equipment, was submitted to the IEC-CENELEC parallel vote and
was approved by CENELEC as EN 60384-25-1 on 2006-07-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2007-04-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2009-07-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60384-25-1:2006 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 4 ----------------------

SIST EN 60384-25-1:2007
- 3 - EN 60384-25-1:2006
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.


Publication Year Title EN/HD Year

IEC 60384-1 (mod) 1999 Fixed capacitors for use in electronic EN 60384-1 2001
equipment + corr. October 2001
Part 1: Generic specification


1) 2)
IEC 60384-25 - Fixed capacitors for use in electronic EN 60384-25 2006
equipment
Part 25: Sectional specification: Surface
mount fixed aluminium electrolytic capacitors
with conductive polymer solid electrolyte






1)
Undated reference.
2)
Valid edition at date of issue.

---------------------- Page: 5 ----------------------

SIST EN 60384-25-1:2007

---------------------- Page: 6 ----------------------

SIST EN 60384-25-1:2007


INTERNATIONAL IEC


STANDARD 60384-25-1





First edition
2006-06


Fixed capacitors for use in electronic equipment –
Part 25-1:
Blank detail specification –
Surface mount fixed aluminium electrolytic
capacitors with conductive polymer solid
electrolyte – Assessment level EZ
 IEC 2006  Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale N
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue

---------------------- Page: 7 ----------------------

SIST EN 60384-25-1:2007
– 2 – 60384-25-1  IEC:2006(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 25-1: Blank detail specification – Surface mount fixed aluminum
electrolytic capacitors with conductive polymer solid electrolyte –
Assessment level EZ


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in
addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment
declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses
arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60384-25-1 has been prepared by IEC technical committee 40:
Capacitors and resistors for electronic equipment.
The text of this standard is based on the following documents:
FDIS Report on voting
40/1734/FDIS 40/1757/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 8 ----------------------

SIST EN 60384-25-1:2007
60384-25-1  IEC:2006(E) – 3 –
IEC 60384 consists of the following parts, under the general title Fixed capacitors for use in
electronic equipment:
Part 1: Generic specification
Part 2: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric
d.c. capacitors
Part 3: Sectional specification: Fixed tantalum chip capacitors
Part 4: Sectional specification: Aluminium electrolytic capacitors with solid and non-solid
electrolyte
Part 5: Sectional specification: Fixed mica delectric d.c. capacitors with a rated voltage not
exceeding 3 000 V – Selection of methods of test and general requirements
Part 6: Sectional specification: Fixed metallized polycarbonate film dielectric d.c.
capacitors
Part 7: Sectional specification: Fixed polystyrene film dielectric metal foil d.c. capacitors
Part 8: Sectional specification: Fixed capacitors of ceramic dielectric, Class 1
Part 9: Sectional specification: Fixed capacitors of ceramic dielectric, Class 2
Part 11: Sectional specification: Fixed polyethylene-terephthalate film dielectric metal foil
d.c. capacitors
Part 12: Sectional specification: Fixed polycarbonate film dielectric metal foil d.c. capacitors
Part 13: Sectional specification: Fixed polypropylene film dielectric metal foil d.c. capacitors
Part 14: Sectional specification: Fixed capacitors for electromagnetic interference
suppression and connection to the supply mains
Part 15: Sectional specification: Fixed tantalum capacitors with non-solid or solid electrolyte
Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c.
capacitors
Part 17: Sectional specification: Fixed metallized polypropylene film dielectric a.c. and pulse
capacitors
Part 18: Sectional specification: Fixed aluminium electrolytic chip capacitors with solid and
non-solid electrolyte
Part 19: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric
chip d.c. capacitors
Part 20: Sectional specification: Fixed metallized polyphenylene sulphide film dielectric chip
d.c. capacitors
Part 21: Sectional specification: Fixed surface mount multilayer capacitors of ceramic
dielectric, Class 1
Part 22: Sectional specification: Fixed surface mount multilayer capacitors of ceramic
dielectric, Class 2
Part 23: Sectional specification: Fixed surface mount metallized polyethylene naphthalate
film dielectric d.c. capacitors
Part 24: Sectional specification: Surface mount fixed tantalum electrolytic capacitors with
conductive polymer solid electrolyte
Part 25: Sectional specification: Surface mount fixed aluminium electrolyte capacitors with
conductive polymer solid electrolyte
All sectional specifications mentioned above do have one or more blank detail specifications
being a supplementary document, containing requirements for style, layout and minimum
content of detail specifications.

---------------------- Page: 9 ----------------------

SIST EN 60384-25-1:2007
– 4 – 60384-25-1  IEC:2006(E)
The committee has decided that the contents of this publication will remain unchanged until the
maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

---------------------- Page: 10 ----------------------

SIST EN 60384-25-1:2007
60384-25-1  IEC:2006(E) – 5 –
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 25-1: Blank detail specification – Surface mount fixed aluminium
electrolytic capacitors with conductive polymer solid electrolyte –
Assessment level EZ



Blank detail specification
A blank detail specification is a supplementary document to the sectional specification and
contains requirements for style, layout and minimum content of detail specifications. Detail
specifications not complying with these requirements may not be considered as being in
accordance with IEC specifications nor shall they so be described.
In the preparation of detail specifications the content of 1.4 of the sectional specification shall be
taken into account.
The numbers between square brackets on the first page of the detail specification correspond to
the following information, which shall be inserted in the position indicated.
Identification of the detail specification
[1] The "International Electrotechnical Commission" or the National Standards
Organization under whose authority the detail specification is drafted.
[2] The IEC or National S
...