SIST EN 60384-4:2016

SLOVENSKI STANDARD
SIST EN 60384-4:2016
01-december-2016
1DGRPHãþD
SIST EN 60384-4:2008
1HVSUHPHQOMLYLNRQGHQ]DWRUML]DXSRUDERYHOHNWURQVNLRSUHPLGHO3RGURþQD
VSHFLILNDFLMD1HVSUHPHQOMLYLDOXPLQLMVNLHOHNWUROLWVNLNRQGHQ]DWRUMLVWUGLP0Q2
LQQHWUGLPHOHNWUROLWRP,(&
Fixed capacitors for use in electronic equipment - Part 4: Sectional specification - Fixed
aluminium electrolytic capacitors with solid (MnO2) and non-solid electrolyt (IEC 60384-
4:2016)
Ta slovenski standard je istoveten z: EN 60384-4:2016
ICS:
31.060.50 Aluminijski elektrolitni Aluminium electrolytic
kondenzatorji capacitors
SIST EN 60384-4:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60384-4:2016

---------------------- Page: 2 ----------------------

SIST EN 60384-4:2016


EUROPEAN STANDARD EN 60384-4

NORME EUROPÉENNE

EUROPÄISCHE NORM
October 2016
ICS 31.060.50 Supersedes EN 60384-4:2007
English Version
Fixed capacitors for use in electronic equipment - Part 4:
Sectional specification - Fixed aluminium electrolytic capacitors
with solid (MnO ) and non-solid electrolyte
2
(IEC 60384-4:2016)
Condensateurs fixes utilisés dans les équipements Festkondensatoren zur Verwendung in Geräten der
électroniques - Partie 4: Spécification intermédiaire - Elektronik - Teil 4: Rahmenspezifikation - Aluminium-
Condensateurs électrolytiques à l'aluminium, à électrolyte Elektrolyt-Kondensatoren mit festen (MnO ) und flüssigen
2
solide ( MnO ) et non solide Elektrolyten
2
(IEC 60384-4:2016) (IEC 60384-4:2016)
This European Standard was approved by CENELEC on 2016-09-16. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 60384-4:2016 E

---------------------- Page: 3 ----------------------

SIST EN 60384-4:2016
EN 60384-4:2016
European foreword
The text of document 40/2467/FDIS, future edition 5 of IEC 60384-4, prepared by IEC/TC 40
"Capacitors and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN 60384-4:2016.
The following dates are fixed:
(dop) 2017-06-16
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
• latest date by which the national standards conflicting with (dow) 2019-09-16
the document have to be withdrawn

This document supersedes EN 60384-4:2007.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60384-4:2016 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60384-18 NOTE Harmonized as EN 60384-18.

2

---------------------- Page: 4 ----------------------

SIST EN 60384-4:2016
EN 60384-4:2016

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60063 -  Preferred number series for resistors and EN 60063 -
capacitors
IEC 60068-1 2013 Environmental testing -- Part 1: General EN 60068-1 2014
and guidance
IEC 60068-2-54 2006 Environmental testing - Part 2-54: Tests - EN 60068-2-54 2006
Test Ta: Solderability testing of electronic
components by the wetting balance
method
IEC 60384-1 2016 Fixed capacitors for use in electronic EN 60384-1 2016
equipment - Part 1: Generic specification
IEC 60417 -  Graphical symbols for use on equipment. - -
Index, survey and compilation of the single
sheets.
IEC 61193-2 2007 Quality assessment systems -- Part 2: EN 61193-2 2007
Selection and use of sampling plans for
inspection of electronic components and
packages
ISO 3 -  Preferred numbers; Series of preferred - -
numbers

3

---------------------- Page: 5 ----------------------

SIST EN 60384-4:2016

---------------------- Page: 6 ----------------------

SIST EN 60384-4:2016



IEC 60384-4

®


Edition 5.0 2016-08




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Fixed capacitors for use in electronic equipment –

Part 4: Sectional specification – Fixed aluminium electrolytic capacitors with

solid (MnO ) and non-solid electrolyte

2



Condensateurs fixes utilisés dans les équipements électroniques –

Partie 4: Spécification intermédiaire – Condensateurs électrolytiques à


l’aluminium, à électrolyte solide (MnO ) et non solide
2













INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 31.060.50 ISBN 978-2-8322-3552-2



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60384-4:2016
– 2 – IEC 60384-4:2016 © IEC 2016
CONTENTS
FOREWORD . 6
1 General . 8
1.1 Scope . 8
1.2 Object . 8
1.3 Normative references . 8
1.4 Information to be given in a detail specification . 9
1.4.1 General . 9
1.4.2 Outline drawing and dimensions . 9
1.4.3 Mounting . 9
1.4.4 Ratings and characteristics . 9
1.4.5 Marking . 10
1.5 Terms and definitions . 10
1.6 Marking . 10
1.6.1 General . 10
1.6.2 Information for marking . 10
1.6.3 Marking on capacitors . 11
1.6.4 Marking on packaging . 11
2 Preferred ratings and characteristics . 11
2.1 Preferred characteristics . 11
2.2 Preferred values of ratings . 11
2.2.1 Nominal capacitance (C ) . 11
N
2.2.2 Tolerance on nominal capacitance . 12
2.2.3 Rated voltage (U ) . 12
R
2.2.4 Category voltage (U ) . 12
C
2.2.5 Ripple voltage . 12
2.2.6 Reverse voltage . 12
2.2.7 Surge voltage ratio . 12
2.2.8 Rated ripple current . 12
3 Quality assessment procedures . 13
3.1 Primary stage of manufacture . 13
3.2 Structurally similar components . 13
3.3 Certified test records of released lots . 13
3.4 Qualification approval (QA) procedures . 13
3.4.1 General . 13
3.4.2 Qualification approval on the basis of the fixed sample size procedure . 13
3.4.3 Tests . 14
3.5 Quality conformance inspection . 26
3.5.1 Formation of inspection lots . 26
3.5.2 Test schedule . 26
3.5.3 Delayed delivery . 26
3.5.4 Assessment levels . 26
4 Test and measurement procedures . 27
4.1 Pre-conditioning (for non-solid electrolyte capacitors only) . 27
4.2 Visual examination and check of dimensions . 28
4.2.1 General . 28
4.2.2 Visual examination and check of dimensions . 28

---------------------- Page: 8 ----------------------

SIST EN 60384-4:2016
IEC 60384-4:2016 © IEC 2016 – 3 –
4.2.3 Requirements . 28
4.3 Electrical tests . 28
4.3.1 Leakage current . 28
4.3.2 Capacitance . 28
4.3.3 Tangent of loss angle (tan δ) or equivalent series resistance (ESR) . 29
4.3.4 Impedance (if required) . 29
4.3.5 Insulation resistance of the external insulation (if required) . 30
4.3.6 Voltage proof of the external insulation (if required) . 30
4.4 Robustness of terminations . 31
4.4.1 General . 31
4.4.2 Initial inspection . 31
4.4.3 Final inspection . 31
4.5 Resistance to soldering heat . 31
4.5.1 General . 31
4.5.2 Test conditions . 31
4.5.3 Recovery . 31
4.5.4 Final inspection and requirements . 31
4.6 Solderability . 31
4.6.1 General . 31
4.6.2 Test conditions . 31
4.6.3 Final inspection . 32
4.7 Rapid change of temperature . 32
4.7.1 General . 32
4.7.2 Initial inspection . 32
4.7.3 Test conditions . 32
4.7.4 Recovery . 32
4.7.5 Final inspections and requirements . 32
4.8 Vibration . 32
4.8.1 General . 32
4.8.2 Test conditions . 32
4.8.3 Final inspections and requirements . 33
4.9 Bump (if required) . 33
4.9.1 General . 33
4.9.2 Test conditions . 33
4.9.3 Final inspections and requirements . 33
4.10 Shock (if required) . 33
4.10.1 General . 33
4.10.2 Test conditions . 33
4.10.3 Final inspections and requirements . 34
4.11 Climatic sequence . 34
4.11.1 General . 34
4.11.2 Initial inspection . 34
4.11.3 Dry heat . 34
4.11.4 Damp heat, cyclic, test Db, first cycle . 34
4.11.5 Cold . 34
4.11.6 Low air pressure (if required). 34
4.11.7 Damp heat, cyclic, test Db, remaining cycles . 35
4.11.8 Sealing (if required) . 35
4.11.9 Final inspections and requirements . 35

---------------------- Page: 9 ----------------------

SIST EN 60384-4:2016
– 4 – IEC 60384-4:2016 © IEC 2016
4.12 Damp heat, steady state . 35
4.12.1 General . 35
4.12.2 Initial inspection . 35
4.12.3 Test conditions . 35
4.12.4 Recovery . 35
4.12.5 Final inspections and requirements . 35
4.13 Endurance . 36
4.13.1 General . 36
4.13.2 Initial inspection . 36
4.13.3 Test conditions . 36
4.13.4 Recovery . 36
4.13.5 Final inspections and requirements . 36
4.14 Surge voltage . 36
4.14.1 General . 36
4.14.2 Initial inspection . 36
4.14.3 Test conditions . 37
4.14.4 Recovery . 37
4.14.5 Final inspections and requirements . 37
4.15 Reverse voltage (if required) . 37
4.15.1 Initial inspection . 37
4.15.2 Test conditions . 37
4.15.3 Recovery . 38
4.15.4 Final inspections and requirements . 38
4.16 Pressure relief (if required) . 38
4.17 Storage at high temperature . 38
4.17.1 General . 38
4.17.2 Initial inspection . 38
4.17.3 Test conditions . 38
4.17.4 Recovery . 38
4.17.5 Final inspections and requirements . 38
4.18 Storage at low temperature (if required) . 38
4.18.1 General . 38
4.18.2 Initial inspection . 38
4.18.3 Test conditions . 38
4.18.4 Recovery . 38
4.18.5 Final inspections and requirements . 39
4.19 Characteristics at high and low temperature . 39
4.19.1 General . 39
4.19.2 Inspections and requirements . 39
4.20 Charge and discharge (if required) . 39
4.20.1 General . 39
4.20.2 Initial inspection . 39
4.20.3 Test conditions . 39
4.20.4 Final inspections and requirements . 39
4.21 High surge current (if required) . 40
4.21.1 General . 40
4.21.2 Final inspections and requirements . 40
4.22 Voltage transient overload (if required) . 40
4.22.1 General . 40

---------------------- Page: 10 ----------------------

SIST EN 60384-4:2016
IEC 60384-4:2016 © IEC 2016 – 5 –
4.22.2 Initial inspection . 40
4.22.3 Final inspections and requirements . 40
Bibliography . 41

Table 1 – Preferred values of tolerances . 12
Table 2 – Sampling plan for qualification approval, assessment level EZ . 15
Table 3 – Test schedule for qualification approval (1 of 10) . 16
Table 4 – Lot-by-lot inspection . 27
Table 5 – Periodic inspection . 27
Table 6 – Amplitude and acceleration options . 33
Table 7 – Preferred severities . 34

---------------------- Page: 11 ----------------------

SIST EN 60384-4:2016
– 6 – IEC 60384-4:2016 © IEC 2016
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 4: Sectional specification –
Fixed aluminium electrolytic capacitors
with solid (MnO ) and non-solid electrolyte
2

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60384-4 has been prepared by IEC technical committee 40:
Capacitors and resistors for electronic equipment.
This fifth edition cancels and replaces the fourth edition published in 2007. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) Revision of the structure
...