iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 12814-5:2001

(Main)

Testing of welded joints of thermoplastics semi-finished products - Part 5: Macroscopic examination

Testing of welded joints of thermoplastics semi-finished products - Part 5: Macroscopic examination

This standard specifies the cutting and preparation of test specimens and the conditions for performing the macroscopic examination of the test specimens. The test is applicable to welded assemblies made from thermoplastics materials filled or unfilled, using the
following processes : - hot gas welding : round nozzle, high speed nozzle, wedge ; - extrusion welding ; - heated tool welding : butt, saddle, socket, wedge ; - electrofusion welding : socket, saddle.

Prüfen von Schweißverbindungen aus thermoplastischen Kunststoffen - Teil 5: Makroskopische Untersuchung

Diese Europäische Norm legt das Probenahmeverfahren, die Herstellung der Probekörper und die Bedingungen zur Durchführung der makroskopischen Untersuchung der Probekörper fest. Die Prüfung ist auf geschweißte Fügeteile aus thermoplastischen Kunststoffen mit oder ohne Füllstoff anwendbar, die nach folgenden Schweißverfahren hergestellt wurden: - Warmgasschweißen: Fächelschweißdüse, Ziehschweißdüse, Heizkeil; - Extrusionsschweißen; - Heizelementschweißen: Stumpfschweißen, Sattelschweißen, Muffenschweißen, Schweißen mit Heizkeil; - Heizwendelschweißen: Muffenschweißen, Sattelschweißen.

Essai des assemblages soudés sur produits semi-finis en thermoplastiques - Part 5: Examen macroscopique

La présente norme spécifie la méthode d'échantillonnage des éprouvettes, ainsi que les conditions pour effectuer l'examen macroscopique sur ces éprouvettes. L'examen est applicable a des assemblages soudés de matieres thermoplastiques chargées ou non chargées, en utilisant les procédés suivants : - soudage au gaz chaud : buse ronde, buse rapide, coin chauffant ; - soudage par extrusion ; - soudage par élément chauffant : bout a bout, selle de raccordement, avec emboîtement, coin chauffant ; - soudage par électrofusion : avec emboîtement, selle de raccordement.

Preskus zvarjenih spojev plastomernih polizdelkov - 5. del: Makroskopska preiskava

General Information

Status
Published
Publication Date
31-May-2001
ICS
25.160.40 - Welded joints and welds
Technical Committee
IPMA - Polimer materials and products
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Jun-2001
Due Date
01-Jun-2001
Completion Date
01-Jun-2001
Ref Project
EN 12814-5:2000 - Testing of welded joints of thermoplastics semi-finished products - Part 5: Macroscopic examination

Relations

Parent
SIST EN 12814-1:2001 - Testing of welded joints of thermoplastics semi-finished products - Part 1: Bend test
Effective Date
22-Dec-2008

Buy Standard

EN 12814-5:2001EN 12814-5:2001
PreviousNext
Standard
EN 12814-5:2001
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Preskus zvarjenih spojev plastomernih polizdelkov - 5. del: Makroskopska preiskavaPrüfen von Schweißverbindungen aus thermoplastischen Kunststoffen - Teil 5: Makroskopische UntersuchungEssai des assemblages soudés sur produits semi-finis en thermoplastiques - Part 5: Examen macroscopiqueTesting of welded joi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 16296:2021(Main)
Imperfections in thermoplastics welded joints - Quality levels
EN 16296:2021

This document provides quality levels for imperfections in thermoplastics welded joints. It applies to material thickness above 2,0 mm.
Three quality levels are given in order to permit application for a wide range of welded fabrication. They are designated by symbols B, C and D, where B is the most stringent. The quality levels refer to production quality and not to the fitness-for-purpose (see 3.2) of the manufactured product.
This document applies to the following thermoplastic materials in Table 1:
Table 1 - Thermoplastic materials
Abbreviation   Material description
ABS   Acrylonitrile-butadiene-styrene plastic
ECTFE   Ethylene-chlorotrifluoroethylene copolymer
FEP   Fluorinated ethylene propylene
PA-U        Unplasticized Polyamide
PB   Polybutylene
PE   Polyethylene
PFA   Perfluoroalkoxy
PP-B   Polypropylene block copolymer
PP-H   Polypropylene homopolymer
PP-R   Polypropylene random copolymer
PVC-C   Chlorinated polyvinyl chloride
PVC-U   Unplasticised polyvinyl chloride (rigid PVC)
PVDF   Polyvinylidene fluoride
and to the following welding processes:
-   heated tool welding;
-   electrofusion welding;
-   hot gas welding using filler rod only;
-   extrusion welding;
-   solvent welding of pipes.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12814-8:2021(Main)
Testing of welded joints of thermoplastics semi-finished products - Part 8: Requirements
EN 12814-8:2021

This document provides the requirements for the tests made on welded thermoplastics semi-finished products.
The selection of the appropriate test method(s) should be made in accordance with the particular type and application of welded product.
The test results depend on the conditions of manufacture for the test specimen and on the test conditions. They can therefore only be related to the behaviour of the product or can only be used for designing a structure, if the test conditions can be related to the service conditions.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12814-2:2021(Main)
Testing of welded joints of thermoplastics semi-finished products - Part 2: Tensile test
EN 12814-2:2021

This document specifies the dimensions, the method of sampling, the preparation of the test specimens and the conditions for performing the tensile test in order to determine the short term tensile welding factor.
A tensile test may be used in conjunction with other tests (e.g. bend, tensile creep, macro) to assess the performance of welded assemblies, made from thermoplastics materials.
The test is applicable to welded assemblies made from thermoplastics materials filled or unfilled, but not reinforced, irrespective of the welding process used.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13100-2:2019(Main)
Non-destructive testing of welded joints in thermoplastics semi-finished products - Part 2: X-ray radiographic testing
EN 13100-2:2019

This document specifies fundamental radiographic techniques which enable repeatable results to be obtained economically.
This document applies to the X-ray radiographic examination of heated tool, electrofusion, extrusion and hot gas joints in plastics materials.
It applies to joints in single wall pipes and plates with a range of thicknesses from 5 mm to 100 mm. It only applies to pipes containing air or other gases at the time of X-ray testing.
This document does not specify acceptance levels of the indications.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14728:2019(Main)
Imperfections in thermoplastic welds - Classification
EN 14728:2019

This draft European Standard specifies a system for classifying imperfections that may be  encountered in thermoplastic welded joints during manufacture and provides examples of imperfections for the following welding processes
-   heated tool butt welding;
-   heated tool socket welding;
-   electrofusion socket welding;
-   hot gas welding;
-   extrusion welding;
-   solvent socket welding.
This document does not describe imperfections that may be generated either during service or present before welding such as poor fit up. The correct preparation (e.g. fit up) is described in the relevant welding procedure specification (WPS). This document is also not concerned with the search for the possible influence of these imperfections on the behaviour of joints in relation to the different types of stress to which the latter may be subjected or on methods for preventing such imperfections.
This document cannot therefore be used to determine the acceptance of welds, which is defined in EN 16296 [1].
Only imperfections giving rise to discontinuities of materials or changes in shape are taken into consideration in this document, specifying their type, their shape and their positions. This classification can be used to determine the possible origin or causes of the imperfections.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12814-4:2018/AC:2018(Corrigendum)
Testing of welded joints of thermoplastics semi-finished products - Part 4: Peel test
EN 12814-4:2018/AC:2018

This document specifies the dimensions, the method of sampling and the preparation of the test specimens, and also the conditions for performing the peel test perpendicular to the weld in order to determine the peel resistance and the failure behaviour.
A peel test can be used in conjunction with other tests (e.g. tensile creep, macroscopic examination...) to assess the performance of welded assemblies, made from thermoplastics materials.
Peel tests are applicable to overlap welded assemblies made from thermoplastics materials.
The T-peel test as defined in Clause 5 will be used only for assessing welded sheet assemblies. This test is not applicable to welded test pieces containing sheets of different nominal thickness.
The decohesion test as defined in Clause 6 will be used only for assessing electrofusion joints with nominal thickness of pipe/fitting greater than 10 mm.
For socket fusion and for electrofusion socket joints with nominal outside diameter less than or equal to 90 mm, a crush test will be used, as defined in Clause 7.
The crush test can also be used for electrofusion joints with outside diameters greater than 90 mm.
The crush test for electrofusion saddle joints will be performed in accordance with ISO 13955 [1].
NOTE   A decohesion test is also defined in ISO 13954 [2].
The tests defined in this standard are not intended to be used for assessment and/or qualification of thermoplastic fittings that already have their own requirements, e.g. polyethylene fittings according to EN 1555-3 [3] and EN 12201-3 [4].

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12814-4:2018(Main)
Testing of welded joints of thermoplastics semi-finished products - Part 4: Peel test
EN 12814-4:2018

This draft European Standard specifies the dimensions, the method of sampling and the preparation of the test specimens, and also the conditions for performing the peel test perpendicular to the weld in order to determine the peel resistance and the failure behaviour.
A peel test may be used in conjunction with other tests (e.g. tensile creep, macroscopic examination...) to assess the performance of welded assemblies, made from thermoplastics materials.
Peel tests are applicable to overlap welded assemblies made from thermoplastics materials.
The T-peel test as defined in Clause 5 will be used only for assessing welded sheet assemblies. This test is not applicable to welded test pieces containing sheets of different nominal thickness.
The decohesion test as defined in Clause 6 will be used only for assessing electrofusion joints with nominal thickness of pipe/fitting greater than 10 mm.
For socket fusion and for electrofusion socket joints with nominal outside diameter less than or equal to 90 mm, a crush test will be used, as defined in Clause 7.
The crush test can also be used for electrofusion joints with outside diameters greater than 90 mm.
The crush test for electrofusion saddle joints will be performed in accordance with ISO 13955 [6].
NOTE   A decohesion test is also defined in ISO 13954 [5].
The tests defined in this standard should not be used for assessment and/or qualification of thermoplastics fittings, e.g. polyethylene fittings according to EN 1555-3 [1] and EN 12201-3 [2], because they already have their own requirements.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13100-1:2017(Main)
Non destructive testing of welded joints of thermoplastics semi-finished products - Part 1: Visual examination
EN 13100-1:2017

This European Standard covers the visual examination of welds in thermoplastic materials. It may also be applied to visual testing of the joint prior to and during the welding.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13100-4:2014(Main)
Non destructive testing of welded joints of thermoplastics semifinished products - Part 4: High voltage testing
EN 13100-4:2012

This European Standard specifies the equipment and methods for the high voltage testing of butt or overlap welded joints in thermoplastic sheets for locating through-thickness defects only. It applies to new unused constructions only.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12814-3:2014(Main)
Testing of welded joints in thermoplastics semi-finished products - Part 3: Tensile creep test
EN 12814-3:2014

EN 12814-3 specifies the dimensions, the method of sampling and the preparation of the test specimens, and the conditions for performing the tensile creep test perpendicular to the weld in order to determine the long term tensile welding factor. A tensile creep test may be used in conjunction with other tests (e.g. bend test, tensile test, macrographic examination...) to assess the performance of welded assemblies, made from thermoplastics materials. The test is applicable to welded assemblies made from thermoplastics materials filled or unfilled such as tubes and fittings, sheets, plates and profiles, but not reinforced, irrespective of the welding process used.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day