SIST EN 12274-2:2004
(Main)Slurry surfacing - Test methods - Part 2: Determination of residual binder content
Slurry surfacing - Test methods - Part 2: Determination of residual binder content
This Draft European Standard describes the apparatus and the procedure for the extraction test to determine the residual binder content for samples of Slurry mixes. This Draft European Standard also describes the apparatus and the procedure for removal of the water from the samples before carrying out the extraction test. This method can only be used to determine the quantity of binder and not to investigate its quality.
Dünne Asphaltschicht in Kaltbauweise - Prüfverfahren - Teil 2: Bestimmung des Bindemittelgehaltes
Dieser Europäische Norm-Entwurf beschreibt die Prüfeinrichtungen und die Durchführung der Extraktionsprüfung zur Bestimmung des Bindemittelgehaltes von Proben aus Mischgut. Dieser Europäische Norm-Entwurf beschreibt auch die Prüfeinrichtungen und die Durchführung, um vor der Extraktionsprüfung das Wasser aus den Proben zu entfernen. Dieses Verfahren kann nur angewendet werden,um die Menge des Bindemittels zu bestimmen, jedoch nicht zur Untersuchung seiner Qualität.
Matériaux bitumineux coulés a froid - Méthode d'essai - Partie 2: Détermination de la teneur en liant résiduel
La présente Norme européenne précise les exigences concernant les mesures sur les bogies a trois essieux, qui assurent que les opérations de mesure sont effectuées en fonction de criteres unifiés. Elle est applicable aux bogies a trois essieux neufs ou modifiés.
Les prescriptions allant au-dela du domaine d'application et de ses exigences font l'objet d'un contrat particulier entre les parties concernées.
Les opérations de mesure se rapportent aux châssis dans leur totalité avec ou sans superstructure, ou a certaines parties de ceux-ci lorsque leur conception géométrique ne permet pas de faire autrement. Il y a lieu, le cas échéant, de procéder a des opérations de mesure supplémentaires, non prévues ici, qui sont déterminées au cas par cas.
Obnovitev površine z emulzijo – Preskusne metode - 2. del: Ugotavljanje deleža ostankov veziva
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Obnovitev površine z emulzijo –
Preskusne metode - 2. del: Ugotavljanje deleža ostankov vezivaDünne Asphaltschicht in Kaltbauweise - Prüfverfahren - Teil 2: Bestimmung des BindemittelgehaltesMatériaux bitumineux coulés a froid - Méthode d'essai - Partie 2: Détermination de la teneur en liant résiduelSlurry surfacing - Test methods - Part 2: Determination of residual binder content93.080.20Materiali za gradnjo cestRoad construction materialsICS:Ta slovenski standard je istoveten z:EN 12274-2:2003SIST EN 12274-2:2004en01-junij-2004SIST EN 12274-2:2004SLOVENSKI
STANDARD
SIST EN 12274-2:2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12274-2January 2003ICS 93.080.20English versionSlurry surfacing - Test methods - Part 2: Determination ofresidual binder contentMatériaux bitumineux coulés à froid - Méthode d'essai -Partie 2: Détermination de la teneur en liant résiduelDünne Asphaltschicht in Kaltbauweise - Prüfverfahren - Teil2: Bestimmung des BindemittelgehaltesThis European Standard was approved by CEN on 21 November 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12274-2:2003 ESIST EN 12274-2:2004
EN 12274-2:2003 (E)2ContentspageForeword.31Scope.32Normative references.43Principle.44Apparatus.45Preparation of sample.46Test procedure.57Test report.5SIST EN 12274-2:2004
EN 12274-2:2003 (E)3ForewordThis document (EN 12274-2:2003) has been prepared by Technical Committee CEN/TC 227 "Road materials", thesecretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by July 2003, and conflicting national standards shall be withdrawn at the latest byApril 2005.This European Standard is one of a series of standards as listed below:EN 12274-1, Slurry surfacing - Test methods - Part 1: Sampling for binder extraction.EN 12274-2, Slurry surfacing - Test methods - Part 2: Determination of residual binder content.EN 12274-3, Slurry surfacing - Test methods - Part 3: Consistency.EN 12274-4, Slurry surfacing - Test methods - Part 4: Determination of cohesion of the mix.EN 12274-5, Slurry surfacing - Test methods - Part 5: Determination of wearing.EN 12274-6, Slurry surfacing - Test methods - Part 6: Rate o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.