iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST HD 323.2.20 S3:2003

(Main)

Basic environmental testing procedures -- Part 2: Tests - Test T: Soldering

Basic environmental testing procedures -- Part 2: Tests - Test T: Soldering

Describes solderability tests on wire and tag terminations (Ta) and printed wiring boards (Tc), also describes tests for resistance to soldering heat, applicable to components (Tb).

Umweltprüfungen -- Teil 2: Prüfungen - Prüfgruppe T: Löten

Essais fondamentaux climatiques et de robustesse mécanique -- Partie 2: Essais - Essai T: Soudure

Décrit les modes opératoires des essais de "soudabilité" applicables aux sorties par fils ou par cosses (Ta), ou aux cartes de circuits imprimés (Tc) : décrit les essais de résistance à la chaleur de soudage, applicables aux composants (Tb).

Basic environmental testing procedures - Part 2: Tests - Test T: Soldering

General Information

Status
Published
Publication Date
30-Jun-2003
ICS
19.040 - Environmental testing
Technical Committee
ITIV - Electronics assembly technology and Environmental standardization
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Jul-2003
Due Date
01-Jul-2003
Completion Date
01-Jul-2003
Ref Project
HD 323.2.20 S3:1988 - Basic environmental testing procedures - Part 2: Tests - Test T: Soldering

Relations

Replaced By
SIST EN 60068-2-20:2009 - Environmental testing -- Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
Effective Date
29-Jan-2023
Revised
SIST EN 60068-2-20:2009 - Environmental testing -- Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
Effective Date
02-Aug-2011
Replaced By
SIST EN 60068-2-20:2009 - Environmental testing -- Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
Effective Date
01-Aug-2011

Buy Standard

HD 323.2.20 S3:2003HD 323.2.20 S3:2003
PreviousNext
Standardization document
HD 323.2.20 S3:2003
English language
31 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI SIST HD 323.2.20 S3:2003

STANDARD
julij 2003
Basic environmental testing procedures - Part 2: Tests - Test T: Soldering
ICS 19.040 Referenčna številka
SIST HD 323.2.20 S3:2003(en)
©  S
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 60068-2-21:2021(Main)
Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
EN IEC 60068-2-21:2021

This document specifies two separate methods for determining the resistance of a material to wet and
dry abrasion.
It is applicable to the coated surface or surfaces of coated fabrics.
It does not apply to determining the abrasion behaviour of an uncoated surface of a coated fabric, for
which the methods for uncoated textiles described in the ISO 12947 series apply.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60068-2-20:2021(Main)
Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
EN IEC 60068-2-20:2021

This part of IEC 60068 outlines Tests Ta and Tb, applicable to devices with leads and leads
themselves. Soldering tests for surface mounting devices (SMD) are described in
IEC 60068‑2‑58.
This document provides procedures for determining the solderability and resistance to soldering
heat of devices in applications using solder alloys, which are eutectic or near eutectic tin lead
(Pb), or lead-free alloys.
The procedures in this document include the solder bath method and soldering iron method.
The objective of this document is to ensure that component lead or termination solderability
meets the applicable solder joint requirements of IEC 61191-3 and IEC 61191-4. In addition,
test methods are provided to ensure that the component body can be resistant to the heat load
to which it is exposed during soldering.
NOTE Information about wetting time and wetting force can be obtained by test methods using a wetting balance.
IEC 60068-2-69 (solder bath and solder globule method) can be consulted.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60068-2-69:2017/A1:2021(Amendment)
Environmental testing - Part 2-69: Tests - Test Te/Tc: Solderability testing of electronic components and printed boards by the wetting balance (force measurement) method
EN 60068-2-69:2017/A1:2019
  • Amendment
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60068-2-82:2019(Main)
Environmental testing - Part 2-82: Tests - Test Xw1: Whisker test methods for components and parts used in electronic assemblies
EN IEC 60068-2-82:2019

This part of IEC 60068 specifies tests for the whiskering propensity of surface finishes of
electric or electronic components and mechanical parts such as punched/stamped parts (for
example, jumpers, electrostatic discharge protection shields, mechanical fixations, press-fit
pins and other mechanical parts used in electronic assemblies) representing the finished
stage, with tin or tin-alloy finish. Changes of the physical dimensions of mould compounds,
plastics and the like during the required test flow are not considered or assessed. The test
methods have been developed by using a knowledge-based approach.
This document can also be used at sub-suppliers, like plating shops, stamping shops or other
service providers to ensure a consistent surface quality within the supply chain.
These test methods are employed with defined acceptance criteria by a relevant component
or application specification.
The tests described in this document are applicable for initial qualification, for periodic
monitoring in accordance with Clause 7, and for changes of technology or manufacturing
processes of existing surfaces in accordance with Clause 9.
The mating area of connectors is not covered by this test method. IEC 60512-16-21 applies
for the mating areas of connectors.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60068-2-58:2015/A1:2018(Amendment)
Environmental testing - Part 2-58: Tests - Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD)
EN 60068-2-58:2015/A1:2018
  • Amendment
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60068-2-69:2017/AC:2018(Corrigendum)
Environmental testing - Part 2-69: Tests - Test Te/Tc: Solderability testing of electronic components and printed boards by the wetting balance (force measurement) method
EN 60068-2-69:2017/AC:2018-03

IEC corrigendum

  • Corrigendum
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60068-2-69:2017(Main)
Environmental testing - Part 2-69: Tests - Test Te/Tc: Solderability testing of electronic components and printed boards by the wetting balance (force measurement) method
EN 60068-2-69:2017

This part of IEC 60068 outlines test Te/Tc, the solder bath wetting balance method and the
solder globule wetting balance method to determine, quantitatively, the solderability of the
terminations. Data obtained by these methods are not intended to be used as absolute
quantitative data for pass–fail purposes.
The procedures describe the solder bath wetting balance method and the solder globule
wetting balance method. They are applicable to components and printed boards with metallic
terminations and metallized solder pads.
This document provides the measurement procedures for solder alloys both with and without
lead (Pb).

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60068-3-13:2016(Main)
Environmental testing - Part 3-13: Supporting documentation and guidance on test T: Soldering
EN 60068-3-13:2016

This part of IEC 60068 provides background information and guidance for writers and users of
specifications for electric and electronic components, containing references to the test
standards IEC 60068-2-20, IEC 60068-2-58, IEC 60068-2-69, IEC 60068-2-83, and to
IEC 61760-1, which defines requirements to the specification of surface mounting
components.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60068-2-58:2015(Main)
Environmental testing - Part 2-58: Tests - Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD)
EN 60068-2-58:2015

This part of IEC 60068 outlines test Td, applicable to surface mounting devices (SMD).
This standard provides procedures for determining the solderability and resistance to
soldering heat of devices in applications using solder alloys, which are eutectic or near
eutectic tin lead (Pb), or lead-free alloys.
The procedures use either a solder bath or reflow method and are applicable only to
specimens or products designed to withstand short term immersion in molten solder or limited
exposure to reflow systems.
The solder bath method is applicable to SMDs designed for flow soldering and SMDs
designed for reflow soldering when the solder bath (dipping) method is appropriate.
The reflow method is applicable to the SMD designed for reflow soldering, to determine the
suitability of SMDs for reflow soldering and when the solder bath (dipping) method is not
appropriate.
The objective of this standard is to ensure solderability of component lead or termination. In
addition, test methods are provided to ensure that the component body can resist against the
heat load to which it is exposed during soldering.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62137-3:2012(Main)
Electronics assembly technology - Part 3: Selection guidance of environmental and endurance test methods for solder joints
EN 62137-3:2012

IEC 62137-3:2011 describes the selection methodology of an appropriate test method for a reliability test for solder joints of various shapes and types of surface mount devices (SMD), array type devices and leaded devices, and lead insertion type devices using various types of solder material alloys. This first edition cancels and replaces IEC/PAS 62137-3, published in 2008, and includes some editorial revisions. The main changes with respect to the PAS include the following:
- no technical changes;
- some editorial changes and corrections;
- for the sake of convenience some constitutive changes.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day