SIST EN 62841-3-6:2014

SLOVENSKI STANDARD
SIST EN 62841-3-6:2014
01-oktober-2014
1DGRPHãþD
SIST EN 61029-2-6:2010
(OHNWULþQDPRWRUQDURþQDRURGMDSUHQRVQDRURGMDWHUVWURML]DWUDWRLQYUW9DUQRVW
GHO3RVHEQH]DKWHYH]DGLDPDQWQHVYHGUHVWHNRþLQVNLPVLVWHPRP,(&

Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden
Machinery - Safety - Part 3-6: Particular requirements for diamond drills with liquid
system
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses -
Sécurité - Partie 3-6: Règles particulières pour les forets diamantés transportables avec
système liquide
Ta slovenski standard je istoveten z: EN 62841-3-6:2014
ICS:
25.080.40 Vrtalniki Drilling machines
25.140.20 (OHNWULþQDRURGMD Electric tools
SIST EN 62841-3-6:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 62841-3-6:2014

---------------------- Page: 2 ----------------------

SIST EN 62841-3-6:2014


EUROPEAN STANDARD EN 62841-3-6

NORME EUROPÉENNE

EUROPÄISCHE NORM
August 2014
ICS 25.140.20 Supersedes EN 61029-2-6:2010
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 3-6: Particular
requirements for transportable diamond drills with liquid system
(IEC 62841-3-6:2014)
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 3-6: Exigences transportable Werkzeuge und Rasen- und
particulières pour les forets diamantés transportables avec Gartenmaschinen - Sicherheit - Teil 3-6: Besondere
système liquide Anforderungen für transportable Diamantbohrmaschinen
(CEI 62841-3-6:2014) mit Flüssigkeitssystem
(IEC 62841-3-6:2014)
This European Standard was approved by CENELEC on 2014-05-02. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 62841-3-6:2014 E

---------------------- Page: 3 ----------------------

SIST EN 62841-3-6:2014
EN 62841-3-6:2014 - 2 -

Foreword
The text of document 116/165/FDIS, future edition 1 of IEC 62841-3-6, prepared by IEC/TC 116
"Safety of motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN 62841-3-6:2014.

A draft amendment, which covers common modifications to IEC 62841-3-6:2014, was prepared by
CLC/TC 116 "Safety of motor-operated electric tools" and approved by CENELEC.

The following dates are fixed:

• latest date by which this document has (dop) 2015-05-02
to be implemented at national level
by publication of an identical
national standard or by endorsement
• latest date by which the national (dow) 2018-05-02
standards conflicting with this document
have to be withdrawn

EN 62841-3-6:2014 supersedes EN 61029-2-6:2010.

This document has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association, and supports essential requirements of
EU Directive(s).

For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this
document.

Clauses, subclauses, notes, tables, figures and annexes which are additional to those in
IEC 62841-3-6 are prefixed “Z”.

This European Standard is divided into four parts:

Part 1: General requirements which are common to most electric motor operated tools (for the
purpose of this standard referred to simply as tools) which could come within the scope of
this standard;
Part 2, 3 or 4: Requirements for particular types of tools which either supplement or modify the
requirements given in Part 1 to account for the particular hazards and characteristics of
these specific tools.

1)
This Part 3-6 is to be used in conjunction with EN 62841-1:201X . When this standard states "addition",
"modification" or "replacement", the relevant text in Part 1 is to be adapted accordingly.

Subclauses, tables and figures which are additional to those in Part 1 are numbered starting from 101.

Compliance with the clauses of Part 1 together with this Part 3-6 provides one means of conforming with the
essential health and safety requirements of the Directive concerned.

Warning: Other requirements and other EU Directives can be applicable to the products falling within the
scope of this standard.

This European Standard follows the overall requirements of EN ISO 12100.

NOTE In this standard the following print types are used:
- requirements proper; in roman type
test specifications: in italic type;
-
- explanatory matter: in smaller roman type.
Words in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the associated noun are
also in bold.
———————
1)
At draft stage.

---------------------- Page: 4 ----------------------

SIST EN 62841-3-6:2014
- 3 - EN 62841-3-6:2014
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.

---------------------- Page: 5 ----------------------

SIST EN 62841-3-6:2014
EN 62841-3-6:2014 - 4 -
COMMON MODIFICATIONS
Replace the title of Annex I by the following:
Annex I
(normative)

Measurement of noise and vibration emissions

Add the following annex:
Annex ZZ
(informative)

Coverage of Essential Requirements of Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all relevant
Essential Requirements as given in EU Directive 2006/42/EC (Machinery Directive).
Compliance with this standard provides one means of conformity with the specified essential requirements of
the Directives concerned.
WARNING: Other requirements and other EU Directives may be applicable to the products falling within the
scope of this standard.
___________

---------------------- Page: 6 ----------------------

SIST EN 62841-3-6:2014



IEC 62841-3-6

®


Edition 1.0 2014-05




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Electric motor-operated hand-held tools, transportable tools and lawn and

garden machinery – Safety –

Part 3-6: Particular requirements for transportable diamond drills with liquid


system



Outils électroportatifs à moteur, outils portables et machines pour jardins et


pelouses – Sécurité –

Partie 3-6: Exigences particulières pour les forets diamantés transportables

avec système liquide










INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX Q


ICS 25.140.20 ISBN 978-2-8322-1540-1



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 62841-3-6:2014
– 2 – IEC 62841-3-6:2014 © IEC 2014
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General requirements . 5
5 General conditions for the tests . 6
6 Radiation, toxicity and similar hazards . 6
7 Classification . 6
8 Marking and instructions . 6
9 Protection against access to live parts . 7
10 Starting . 7
11 Input and current . 7
12 Heating . 8
13 Resistance to heat and fire . 8
14 Moisture resistance . 8
15 Resistance to rusting . 8
16 Overload protection of transformers and associated circuits . 8
17 Endurance . 8
18 Abnormal operation . 9
19 Mechanical hazards . 9
20 Mechanical strength . 10
21 Construction . 10
22 Internal wiring . 11
23 Components . 11
24 Supply connection and external flexible cords . 11
25 Terminals for external conductors . 11
26 Provision for earthing . 11
27 Screws and connections . 11
28 Creepage distances, clearances and distances through insulation . 11
Annexes . 14
Annex I (informative) Measurement of noise and vibration emissions . 14
Annex K (normative) Battery tools and battery packs . 16
Bibliography . 17

Figure 101 – Example of a diamond drill with liquid system . 12
Figure 102 – Test arrangement to check efficiency of the liquid collection device . 13

Table 4 – Required performance levels . 9
Table I.101 – Test conditions for noise and vibration . 14
Table I.102 – Concrete formulation (per cubic metre) . 15
Table I.103 – Depth of holes for the test . 15

---------------------- Page: 8 ----------------------

SIST EN 62841-3-6:2014
IEC 62841-3-6:2014 © IEC 2014 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE
TOOLS AND LAWN AND GARDEN MACHINERY –
SAFETY –

Part 3-6: Particular requirements for transportable
diamond drills with liquid system

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
This part of International Standard IEC 62841 has been prepared by technical committee 116:
Safety of motor-operated electric tools.
The text of this standard is based on the following documents:
FDIS Report on voting
116/165/FDIS 116/179/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 9 ----------------------

SIST EN 62841-3-6:2014
– 4 – IEC 62841-3-6:2014 © IEC 2014
This Part 3-6 is to be used in conjunction with IEC 62841-1:2014.
This Part 3-6 supplements or modifies the corresponding clauses in IEC 62841-1, so as to
convert it into the IEC Standard: Particular requirements for transportable diamond drills with
liquid system.
Where a particular subclause of Part 1 is not mentioned in this Part 3-6, that subclause
applies as far as is reasonable. Where this standard states "addition", "modification" or
"replacement", the relevant text in Part 1 is to be adapted accordingly.
The following print types are used:
– requirements: in roman type;
– test specifications: in italic type;
– notes: in small roman type.
The terms defined in Clause 3 are printed in bold typeface.
Subclauses, notes and figures which are additional to those in Part 1 are numbered starting
from 101.
A list of all parts of the IEC 62841 series, under the general title: Electric motor-operated
hand-held tools, transportable tools and lawn and garden machinery – Safety, can be found
on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
NOTE The attention of National Committees is drawn to the fact that equipment manufacturers and testing
organizations may need a transitional period following publication of a new, amended or revised IEC publication in
which to
...