SIST EN ISO 19932-3:2025

SLOVENSKI STANDARD
01-oktober-2025
Oprema za zaščito poljščin - Nahrbtni škropilniki - 3. del: Preverjanje delovanja
nahrbtnih škropilnikov (ISO 19932-3:2025)
Equipment for crop protection - Knapsack sprayers - Part 3: Inspection of knapsack
sprayers in use (ISO 19932-3:2025)
Pflanzenschutzgeräte - Tragbare Geräte - Teil 3: Kontrolle von in Gebrauch befindlichen
Geräten (ISO 19932-3:2025)
Matériel de protection des cultures - Pulvérisateurs à dos - Partie 3: Contrôle des
pulvérisateurs portables à dos en service (ISO 19932-3:2025)
Ta slovenski standard je istoveten z: EN ISO 19932-3:2025
ICS:
65.060.40 Oprema za nego rastlin Plant care equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 19932-3
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2025
EUROPÄISCHE NORM
ICS 65.060.40
English Version
Equipment for crop protection - Knapsack sprayers - Part
3: Inspection of knapsack sprayers in use (ISO 19932-
3:2025)
Matériel de protection des cultures - Pulvérisateurs à Pflanzenschutzgeräte - Tragbare Geräte - Teil 3:
dos - Partie 3: Contrôle des pulvérisateurs portables à Kontrolle von in Gebrauch befindlichen Geräten (ISO
dos en service (ISO 19932-3:2025) 19932-3:2025)
This European Standard was approved by CEN on 19 April 2025.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19932-3:2025 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the health and
safety and environmental requirements of Directive 2009/128/EC . 4
European foreword
This document (EN ISO 19932-3:2025) has been prepared by Technical Committee ISO/TC 23 "Tractors
and machinery for agriculture and forestry" in collaboration with Technical Committee CEN/TC 144
“Tractors and machinery for agriculture and forestry” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2026, and conflicting national standards
shall be withdrawn at the latest by February 2026.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 19932-3:2025 has been approved by CEN as EN ISO 19932-3:2025 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the health and safety and
environmental requirements of Directive 2009/128/EC
This European Standard has been prepared under Commission’s standardization request "M/435
Mandate to CEN, CENELEC and ETSI for the development of a standards on inspection of pesticide
application equipment in use" to provide one voluntary means of conforming to health and safety and
environmental requirements of the Directive 2009/128/EC of the European Parliament and of the
Council of 21 October 2009 establishing a framework for Community action to achieve the sustainable
use of pesticides [OJ L 309].
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding health and safety and
environmental requirements, of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and annex II of EU Directive
2009/128/EC [OJ L 309]
Health and safety and Clause(s)/sub-clause(s) Remarks/Notes
environmental requirements of EU of this EN
Directive 2009/128/EC
Annex II 4.8
— The pesticide application
equipment must function reliably and
be used properly for its intended
purpose ensuring that pesticides can
be accurately dosed and distributed.
— The equipment must be in such a
4.3, 7.1
condition as to be filled and emptied
safely, easily and completely and
prevent leakage of pesticides.
— It must permit easy and thorough
6.1.2, 8 It is not possible to test
cleaning.
cleaning efficiency without
disassembling the sprayer
which is not practical. Due to
small tank sizes (<25 litres)
there are very limited
pesticide residues.
— It must also ensure safe
4.2, 4.5, 6.2, 7.2 There is no operator seat
operations, and be controlled and
since these are manually
capable of being immediately stopped
carried sprayers.
from the operator’s seat.
— Where necessary, adjustments
4.5.3
must be simple, accurate and capable
Health and safety and Clause(s)/sub-clause(s) Remarks/Notes
environmental requirements of EU of this EN
Directive 2009/128/EC
of being reproduced.
1) Power transmission parts
6.3, 6.6 Only applicable for engine
driven knapsack sprayers.
2) Pump
4.8.2
3) Agitation
Not relevant These manually carried
sprayers generally have very
small tanks (<25 litres)
which empty rapidly, with
any agitation required
achieved by the movement of
the spray tank on the
operators back.
4) Spray liquid tank
4.3, 5, 6.1
5) Measuring systems, control and
4.5, 4.8, 6.2, 7.2
regulation systems
6) Pipes and hoses
4.6
7) Filtering
4.7, 5
8) Spray boom
4.8.2
9) Nozzles
4.8
10) Distribution
4.8.1
11) Blower
Not relevant Not present on these
sprayers.
WARNING 1 Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
International
Standard
ISO 19932-3
First edition
Equipment for crop protection —
2025-04
Knapsack sprayers —
Part 3:
Inspection of knapsack sprayers in
use
Matériel de protection des cultures — Pulvérisateurs à dos —
Partie 3: Contrôle des pulvérisateurs portables à dos en service
Reference number
ISO 19932-3:2025(en) © ISO 2025

ISO 19932-3:2025(en)
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 19932-3:2025(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements and method of verification . 2
4.1 General requirements .2
4.2 Harness . .2
4.3 Spray tank .2
4.4 Leak test .3
4.5 Controls .3
4.6 Hoses .3
4.7 Filters .3
4.8 Spray output — Lance and nozzles .3
5 Specific requirements for lever-operated knapsack sprayer-tanks . 4
6 Specific requirements for engine- or electric motor-driven knapsack sprayers . 4
6.1 Spray tank .4
6.2 Controls .4
6.3 Power-driven components .4
6.4 Fuel tank .5
6.5 Exhaust system .
...