SIST EN ISO 28139:2021/A1:2024

SLOVENSKI STANDARD
01-julij-2024
Oprema za zaščito poljščin - Nahrbtna škropilnica na zračni tlak s pogonskim
motorjem - Varnostne in okoljske zahteve in preskusne metode - Dopolnilo A1
(ISO 28139:2019/Amd 1:2024)
Equipment for crop protection - Knapsack combustion engine-driven airblast sprayers -
Safety and environmental requirements and test methods - Amendment 1 (ISO
28139:2019/Amd 1:2024)
Pflanzenschutzgeräte - Rückentragbare, verbrennungsmotorbetriebene Sprühgeräte -
Sicherheits- und Umweltanforderungen und Prüfverfahren - Änderung 1 (ISO
28139:2019/Amd 1:2024)
Matériel de protection des cultures - Atomiseurs portés à dos motorisés - Exigences de
sécurité et environnementales et méthodes d'essai - Amendement 1 (ISO
28139:2019/Amd 1:2024)
Ta slovenski standard je istoveten z: EN ISO 28139:2021/A1:2024
ICS:
65.060.40 Oprema za nego rastlin Plant care equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 28139:2021/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2024
EUROPÄISCHE NORM
ICS 65.060.40
English Version
Equipment for crop protection - Knapsack combustion
engine-driven airblast sprayers - Safety and environmental
requirements and test methods - Amendment 1 (ISO
28139:2019/Amd 1:2024)
Matériel de protection des cultures - Atomiseurs portés Pflanzenschutzgeräte - Rückentragbare,
à dos motorisés - Exigences de sécurité et verbrennungsmotorbetriebene Sprühgeräte -
environnementales et méthodes d'essai - Amendement Sicherheits- und Umweltanforderungen und
1 (ISO 28139:2019/Amd 1:2024) Prüfverfahren - Änderung 1 (ISO 28139:2019/Amd
1:2024)
This amendment A1 modifies the European Standard EN ISO 28139:2021; it was approved by CEN on 8 March 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 28139:2021/A1:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC amended by Directive 2009/127/EC
aimed to be covered . 4

European foreword
This document (EN ISO 28139:2021/A1:2024) has been prepared by Technical Committee ISO/TC 23
"Tractors and machinery for agriculture and forestry" in collaboration with Technical Committee
CEN/TC 144 “Tractors and machinery for agriculture and forestry” the secretariat of which is held by
AFNOR.
This Amendment to the European Standard EN ISO 28139:2021 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by November 2024,
and conflicting national standards shall be withdrawn at the latest by November 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 28139:2019/Amd 1:2024 has been approved by CEN as EN ISO 28139:2021/A1:2024
without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC amended by Directive
2009/127/EC aimed to be covered
This European Standard has been prepared under Commission’s standardization requests “M/396
mandate to CEN and CENELEC for standardisation in the field of machinery” and "M/471 Mandate to
CEN for standardisation in the field of machinery for pesticide application" to provide one voluntary
means of conforming to essential requirements of the Directive 2009/127/EC of the European
Parliament and of the Council of 17 May 2006 on machinery.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding Essential
Requirements, of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and
EU Directive 2006/42/EC amended by Directive 2009/127/EC
The relevant Essential Clause(s)/sub-clause(s) Remarks/Notes
Requirements of EU Directive of this EN
2006/42/EC amended by
Directive 2009/127/EC
1.1.2. Principles of safety
integration
1.1.2. a 4.2, 4.3, 4.4, 4.5, 4.6, 4.7, 4.8, 4.9,
4.10, 4.11, 4.12, 4.13, 5.1, 5.2, 5.3,
5.4, 5.5, 5.6, 5.7, 5.8, 5.9, 5.10, 7.1,
7.2, 7.3
1.1.2. c 4.2, 4.3, 4.4, 4.5, 4.6, 4.7, 4.8, 4.9,
4.10, 4.11, 4.12, 4.13, 5.1, 5.2, 5.3,
5.4, 5.5, 5.6, 5.7, 5.8, 5.9, 5.10, 7.1,
7.2, 7.3
1.1.2. d 4.2, 4.3, 4.4, 4.5, 4.6, 4.7, 4.8, 4.9,
4.10, 4.11, 4.12, 4.13, 5.1, 5.2, 5.3,
5.4, 5.5, 5.6, 5.7, 5.8, 5.9, 5.10, 7.1,
7.2, 7.3
1.1.3. Materials and products 4.8
1.1.6. Ergonomics 4.5.1, 4.5.2, 4.5.3, 4.5.6, 4.6, 4.6.1
1.1.7. Operating positions 4.3
1.2.1. Safety and reliability of 4.5.1, 4.5.3, 4.5.4, 4.5.5, 4.5.6
control systems
1.2.2. Control devices 4.5.1, 4.5.2, 4.5.3, 4.5.4, 4.5.5,
4.5.6
1.2.3. Starting 4.5.5
1.2.4.1. Normal stop 4.5.4
1.2.4.2. Operational stop 4.5.6
1.3.1. Risk of loss of stability 4.2, 5.9
1.3.7. Risks related to moving 4.7
parts
1.5.1. Electricity supply 4.10
1.5.5. Extreme temperatures 4.9
1.5.6. Fire 4.8
1.5.8. Noise 4.12
1.5.9. Vibrations 4.11
1.7.1. Information and warnings 7.1, 7.2, 7.3
on the machinery
1.7.1.1. Information and 7.1, 7.2, 7.3
information devices
1.7.2. Warning of residual risks 7.3
1.7.3. Marking of machinery 7.2
1.7.4. Instructions 7.1
1.7.4.1. General principles for the 7.1
drafting of instructions
1.7.4.2. Contents of the 7.1
instructions
2.4. MACHINERY FOR PESTICIDE 5
APPLICATION
2.4.2. General 5.1, 5.2, 5.3, 5.4, 5.5, 5.6, 5.7, 5.8,
5.9, 5.10
2.4.4. Filling and emptying 5.3
2.4.5.1. Application rate 5.4, 5.5, 5.7, 5.10
2.4.5.2. Distribution, deposition 5.5, 5.7, 5.10
and drift of pesticide
2.4.5.3. Tests 6.1, 6.2, 6.3, 6.4, 6.5, 6.6, 6.7, 6.8
2.4.5.4. Losses during stoppage 4.5.6
2.4.6.1. Cleaning 5.3, 5.8
2.4.8. Marking of nozzles, 5.4
strainers and filters
2.4.10. Instructions 7.1
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
International
Standard
ISO 28139
Second edition
Equipment for crop protection —
2019-12
Knapsack combustion engine-
driven airblast sprayers — Safety
AMENDMENT 1
and environmental requirements
2024-03
and test methods
AMENDMENT 1
Matériel de protection des cultures — Atomiseurs portés à dos
motorisés — Exigences de sécurité et environnementales et
méthodes d'essai
AMENDEMENT 1
Reference number
ISO 28139:2019/Amd.1:2024(en) © ISO 2024

ISO 28139:2019/Amd.1:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 28139:2019/Amd.1:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws at
...