SIST EN IEC 60068-3-6:2018

SLOVENSKI STANDARD
SIST EN IEC 60068-3-6:2018
01-junij-2018
1DGRPHãþD
SIST EN 60068-3-6:2002
2NROMVNRSUHVNXãDQMHGHO3RGSRUQDGRNXPHQWDFLMDLQQDYRGLOR3RWUMHYDQMH
WHKQLþQLKODVWQRVWLWRSORWQLKYODåQLKNRPRU,(&
Environmental testing - Part 3-6: Supporting documentation and guidance - Confirmation
of the performance of temperature/humidity chambers (IEC 60068-3-6:2018)
Umweltprüfungen - Teil 3-6: Unterstützende Dokumentation und Leitfaden - Bestätigung
des Leistungvermögens von Temperatur-/Klimaprüfkammern (IEC 60068-3-6:2018)
Essais d'environnement - Partie 3-6: Documentation d'accompagnement et guide -
Confirmation des performances des chambres d'essais en température et humidité (IEC
60068-3-6:2018)
Ta slovenski standard je istoveten z: EN IEC 60068-3-6:2018
ICS:
01.110 7HKQLþQDGRNXPHQWDFLMD]D Technical product
L]GHONH documentation
19.040 Preskušanje v zvezi z Environmental testing
okoljem
29.020 Elektrotehnika na splošno Electrical engineering in
general
SIST EN IEC 60068-3-6:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN IEC 60068-3-6:2018

---------------------- Page: 2 ----------------------

SIST EN IEC 60068-3-6:2018


EUROPEAN STANDARD EN IEC 60068-3-6

NORME EUROPÉENNE

EUROPÄISCHE NORM
March 2018
ICS 19.040 Supersedes EN 60068-3-6:2002
English Version
Environmental testing - Part 3-6: Supporting documentation and
guidance - Confirmation of the performance of
temperature/humidity chambers
(IEC 60068-3-6:2018)
Essais d'environnement - Partie 3-6: Documentation Umweltprüfungen - Teil 3-6: Unterstützende Dokumentation
d'accompagnement et guide - Confirmation des und Leitfaden - Bestätigung des Leistungvermögens von
performances des chambres d'essais en température et Temperatur-/Klimaprüfkammern
humidité (IEC 60068-3-6:2018)
(IEC 60068-3-6:2018)
This European Standard was approved by CENELEC on 2018-02-27. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 60068-3-6:2018 E

---------------------- Page: 3 ----------------------

SIST EN IEC 60068-3-6:2018
EN IEC 60068-3-6:2018 (E)
European foreword
The text of document 104/760/FDIS, future edition 2 of IEC 60068-3-6, prepared by IEC/TC 104
"Environmental conditions, classification and methods of test" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 60068-3-6:2018.

The following dates are fixed:
(dop) 2018-11-17
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2021-02-27
standards conflicting with the
document have to be withdrawn

This document supersedes EN 60068-3-6:2002.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 60068-3-6:2018 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60068-1 NOTE Harmonized as EN 60068-1.
IEC 60068-3-4 NOTE Harmonized as EN 60068-3-4.
IEC 60584-1 NOTE Harmonized as EN 60584-1.
IEC 60751 NOTE Harmonized as EN 60751.
ISO 10012 NOTE Harmonized as EN ISO 10012.
2

---------------------- Page: 4 ----------------------

SIST EN IEC 60068-3-6:2018
EN IEC 60068-3-6:2018 (E)

Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.

NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.

NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 60068-3-5 2001 Environmental testing -- Part 3-5: EN 60068-3-5 2002
Supporting documentation and guidance -
Confirmation of the performance of
temperature chambers
IEC 60068-3-7 2001 Environmental testing -- Part 3-7: EN 60068-3-7 2002
Supporting documentation and guidance -
Measurements in temperature chambers
for tests A and B (with load)
IEC 60068-3-11 2007 Environmental testing -- Part 3-11: EN 60068-3-11 2007
Supporting documentation and guidance -
Calculation of the uncertainty of conditions
in climatic test chambers


3

---------------------- Page: 5 ----------------------

SIST EN IEC 60068-3-6:2018

---------------------- Page: 6 ----------------------

SIST EN IEC 60068-3-6:2018



IEC 60068-3-6

®


Edition 2.0 2018-01




INTERNATIONAL



STANDARD



















Environmental testing –

Part 3-6: Supporting documentation and guidance – Confirmation of the

performance of temperature/humidity chambers

























INTERNATIONAL

ELECTROTECHNICAL


COMMISSION





ICS 19.040 ISBN 978-2-8322-5208-6



  Warning! Make sure that you obtained this publication from an authorized distributor.


® Registered trademark of the International Electrotechnical Commission

---------------------- Page: 7 ----------------------

SIST EN IEC 60068-3-6:2018
– 2 – IEC 60068-3-6:2018 © IEC 2018
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Measuring of performances . 9
4.1 Test area environment . 9
4.2 Measurement system . 9
4.3 Temperature measurement system . 9
4.4 Humidity measurement system . 9
4.5 Temperature/humidity chamber test specimens . 10
4.6 Specified location of temperature sensors and humidity sensor in working
space . 10
4.6.1 General . 10
4.6.2 Temperature sensors . 11
4.6.3 Humidity sensor . 11
4.7 Measurement method . 11
4.7.1 General . 11
4.7.2 Achieved humidity . 11
4.7.3 Temperature/humidity stabilization . 12
4.7.4 Humidity fluctuation . 12
4.7.5 Humidity gradient. 13
4.7.6 Humidity variation in space . 14
4.8 Standard humidity sequence . 15
5 Information to be given in the performance test report . 16
Bibliography . 17

Figure 1 – Example of humidity differences . 8
Figure 2 – Working space . 8
Figure 3 – Location sensors for temperature/humidity chambers up to 2 000 l. 10
Figure 4 – Location of minimal additional sensors for temperature/humidity chambers
over 2 000 l . 11
Figure 5 – Example of achieved humidity . 12
Figure 6 – Example of temperature/humidity stabilization . 12
Figure 7 – Example of humidity fluctuation . 13
Figure 8 – Example of humidity gradient for chambers up to 2 000 l . 14
Figure 9 – Example of humidity variation in space for chambers up to 2000 l . 15
Figure 10 – Example of climatogram . 16

Table 1 – Practical dimensions . 9
Table 2 – Example of test sequence . 15

---------------------- Page: 8 ----------------------

SIST EN IEC 60068-3-6:2018
IEC 60068-3-6:2018 © IEC 2018 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

ENVIRONMENTAL TESTING –

Part 3-6: Supporting documentation and guidance –
Confirmation of the performance of temperature/humidity chambers

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60068-3-6 has been prepared by IEC technical committee 104:
Environmental conditions, classification and methods of test.
This second edition cancels and replaces the first edition published in 2001. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) Confirmation procedures are clarified.

---------------------- Page: 9 ----------------------

SIST EN IEC 60068-3-6:2018
– 4 – IEC 60068-3-6:2018 © IEC 2018
The text of this International Standard is based on the following documents:
FDIS Report on voting
104/760/FDIS 104/779/RVD

Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
IEC 60068-3-6 is to be read in conjunction with IEC 60068-3-5:2001 and IEC 60068-3-7:2001.
A list of all parts in the IEC 60068 series, published under the general title Environmental
testing, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of thi
...