SIST EN ISO 7143:2007

SLOVENSKI STANDARD
01-julij-2007
1DGRPHãþD
SIST EN ISO 7143:2004
Veziva za barve in lake - Metode preskušanja za karakterizacijo veziv na vodni
osnovi (ISO 7143:2007)
Binders for paints and varnishes - Methods of test for characterizing water-based binders
(ISO 7143:2007)
Bindemittel für Beschichtungsstoffe - Prüfverfahren zur Charakterisierung von
wasserverdünnbaren Bindemitteln (ISO 7143:2007)
Liants pour peintures et vernis - Méthodes d'essai pour caractériser les liants a base
d'eau (ISO 7143:2007)
Ta slovenski standard je istoveten z: EN ISO 7143:2007
ICS:
87.060.20 Veziva Binders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 7143
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2007
ICS 87.060.20 Supersedes EN ISO 7143:2004
English Version
Binders for paints and varnishes - Methods of test for
characterizing water-based binders (ISO 7143:2007)
Liants pour peintures et vernis - Méthodes d'essai pour Bindemittel für Beschichtungsstoffe - Prüfverfahren zur
caractériser les liants à base d'eau (ISO 7143:2007) Charakterisierung von wasserverdünnbaren Bindemitteln
(ISO 7143:2007)
This European Standard was approved by CEN on 6 February 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7143:2007: E
worldwide for CEN national Members.

Foreword
This document (EN ISO 7143:2007) has been prepared by Technical Committee ISO/TC 35
"Paints and varnishes" in collaboration with Technical Committee CEN/TC 139 "Paints and
varnishes", the secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by August 2007, and conflicting national
standards shall be withdrawn at the latest by August 2007.

This document supersedes EN ISO 7143:2004.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
Kingdom.
Endorsement notice
The text of ISO 7143:2007 has been approved by CEN as EN ISO 7143:2007 without any
modifications.
INTERNATIONAL ISO
STANDARD 7143
Third edition
2007-02-01
Corrected version
2007-04-01
Binders for paints and varnishes —
Methods of test for characterizing water-
based binders
Liants pour peintures et vernis — Méthodes d'essai pour caractériser
les liants à base d'eau
Reference number
ISO 7143:2007(E)
©
ISO 2007
ISO 7143:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved

ISO 7143:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
ISO 7143 was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 10,
Test methods fo
...