SIST EN 13523-14:2023
(Main)Coil coated metals - Test methods - Part 14: Chalking (Helmen method)
Coil coated metals - Test methods - Part 14: Chalking (Helmen method)
This Part of EN 13523 describes the procedure for determining objectively the chalking resulting from natural or artificial weathering of an organic coating on a metallic substrate. The advantage of this procedure for measuring chalking of an organic coating is that the result can be read off immediately on an instrument. Subjective judgement by visual comparison of test specimens with referencee specimens is not necessary. Experience to date with this test method has been based mainly on artificially weathered specimens. Reproductible results can only de obtained by careful execution of the test.
Bandbeschichtete Metalle - Prüfverfahren - Teil 14: Kreiden (Verfahren nach Helmen)
Dieses Dokument legt das Verfahren zum objektiven Bestimmen der Kreidung einer organischen Beschichtung auf einem metallischen Substrat als Folge von Freibewitterung oder künstlicher Bewitterung fest.
Der Vorteil dieses Verfahrens zum Messen der Kreidung einer organischen Beschichtung ist, dass das Ergebnis unmittelbar an einem Messgerät abgelesen werden kann. Eine subjektive Beurteilung durch visuellen Vergleich von Proben mit Bezugsproben ist nicht erforderlich.
Reproduzierbare Ergebnisse können nur erzielt werden, wenn die Prüfung sorgfältig durchgeführt wird. Besonders wird auf das Klebeband und das Aufbringen des Klebebandes auf die zu prüfende Oberfläche geachtet.
Das Prüfverfahren ist nicht anwendbar auf geprägte Beschichtungen. Bei Strukturbeschichtungen beeinflusst der Grad der Strukturierung die Ergebnisse. Auch Schmutzansammlung kann bei freibewitterten Proben die Ergebnisse beeinflussen.
ANMERKUNG Es gibt unterschiedliche Verfahren zum Beurteilen der Kreidung. Die Ergebnisse dieser unterschiedlichen Verfahren sind nicht vergleichbar.
Tôles prélaquées - Méthodes d'essai - Partie 14: Farinage (méthode Helmen)
Le présent document décrit le mode opératoire permettant de déterminer objectivement le farinage d’un revêtement organique appliqué sur un subjectile métallique, résultant d’un vieillissement naturel ou artificiel.
L’avantage de ce mode opératoire de mesurage du farinage d’un revêtement organique est que le résultat peut être lu immédiatement sur un instrument. Il n’est pas nécessaire de réaliser une comparaison visuelle des éprouvettes avec des éprouvettes de référence pour obtenir une évaluation subjective.
Des résultats reproductibles ne peuvent être obtenus que par une exécution minutieuse de l’essai. Une attention particulière est accordée à la qualité du ruban adhésif et à son application sur la surface d’essai.
La méthode d’essai ne s’applique pas aux revêtements en relief. Dans le cas des revêtements texturés, le degré de texture influera sur les relevés. L’accumulation de poussière peut également influer sur les relevés pour les éprouvettes vieillies en extérieur.
NOTE Il existe différentes méthodes d’évaluation du farinage. Les résultats de ces différentes méthodes ne sont pas comparables.
Prevlečene kovine, ki se navijajo - Preskusne metode - 14. del: Kredanje (metoda po Helmenu)
Del standarda EN 13523 opisuje postopek za objektivno določitev kredanja, ki je posledica naravnega ali umetnega staranja organske prevleke na kovinski podlagi. Prednost tega postopka za merjenje kredanja organske prevleke je odčitavanje rezultatov neposredno na instrumentu. Subjektivna ocena z vizualno primerjavo preskusnih vzorcev z referenčnimi ni potrebna. Dosedanje izkušnje s to preskusno metodo temeljijo predvsem na umetno staranih vzorcih. Ponovljive rezultate je mogoče doseči le s skrbno izvedbo preskusa.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13523-14:2023
01-maj-2023
Nadomešča:
SIST EN 13523-14:2014
Prevlečene kovine, ki se navijajo - Preskusne metode - 14. del: Kredanje (metoda
po Helmenu)
Coil coated metals - Test methods - Part 14: Chalking (Helmen method)
Bandbeschichtete Metalle - Prüfverfahren - Teil 14: Kreiden (Verfahren nach Helmen)
Tôles prélaquées - Méthodes d'essai - Partie 14: Farinage (méthode Helmen)
Ta slovenski standard je istoveten z: EN 13523-14:2023
ICS:
17.040.20 Lastnosti površin Properties of surfaces
25.220.60 Organske prevleke Organic coatings
SIST EN 13523-14:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13523-14:2023
---------------------- Page: 2 ----------------------
SIST EN 13523-14:2023
EN 13523-14
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2023
EUROPÄISCHE NORM
ICS 25.220.60 Supersedes EN 13523-14:2014
English Version
Coil coated metals - Test methods - Part 14: Chalking
(Helmen method)
Tôles prélaquées - Méthodes d'essai - Partie 14 : Bandbeschichtete Metalle - Prüfverfahren - Teil 14:
Farinage (méthode Helmen) Kreiden (Verfahren nach Helmen)
This European Standard was approved by CEN on 6 February 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13523-14:2023 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13523-14:2023
EN 13523-14:2023 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 6
5 Apparatus . 6
6 Sampling . 6
7 Test specimens . 6
8 Procedure. 6
8.1 General . 6
8.2 Checking the adhesive tape . 6
8.3 Calibration . 6
8.4 Measurement . 6
9 Expression of results . 7
10 Precision . 7
11 Test report . 7
Bibliography . 8
2
---------------------- Page: 4 ----------------------
SIST EN 13523-14:2023
EN 13523-14:2023 (E)
European foreword
This document (EN 13523-14:2023) has been prepared by Technical Committee CEN/TC 139 “Paints and
varnishes”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2023, and conflicting national standards shall
be withdrawn at the latest by September 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13523-14:2014.
The main changes compared to the previous edition are listed below:
a) the description of the test apparatus has been changed so that the glossmeter is preferred to the
portable chalking apparatus, which is no longer manufactured;
b) the text has been editorially revised and the normative references have been updated.
The EN 13523 series, Coil coated metals — Test methods, consists of the following parts:
— Part 0: General introduction
— Part 1: Film thickness
— Part 2: Gloss
— Part 3: Colour difference and metamerism — Instrumental comparison
— Part 4: Pencil hardness
— Part 5: Resistance to rapid deformation (impact test)
— Part 6: Adhesion after indentation (cupping test)
— Part 7: Resistance to cracking on bending (T-bend test)
— Part 8: Resistance to salt spray (fog)
— Part 9: Resistance to water immersion
— Part 10: Resistance to fluorescent UV radiation and water condensation
— Part 11: Resistance to solvents (rubbing test)
— Part 12: Resistance to scratching
— Part 13: Resistance to accelerated ageing by the use of heat
— Part 14: Chalking (Helmen method)
— Part 16: Resistance to abrasion
3
---------------------- Page: 5 ----------------------
SIST EN 13523-14:2023
EN 13523-14:2023 (E)
— Part 17: Adhesion of strippable films
— Part 18: Resistance to staining
— Part 19: Panel design and method of atmospheric exposure testing
— Part 20: Foam adhesion
— Part 21: Evaluation of outdoor exposed panels
— Part 22: Colour difference — Visual comparison
— Part 23: Resistance to humid atmospheres containing sulfur dioxide
— Part 24: Resistance to blocking and pressure marking
— Part 25: Resistance to humidity
— Part 26: Resistance to condensation of water
— Part 27: Resistance to humid poultice (Cataplasm test)
— Part 29: Resistance to environmental soiling (Dirt pick-up and striping)
Any feedback and questions on this document should
...
SLOVENSKI STANDARD
oSIST prEN 13523-14:2022
01-maj-2022
Prevlečene kovine, ki se navijajo - Preskusne metode - 14. del: Kredanje (metoda
po Helmenu)
Coil coated metals - Test methods - Part 14: Chalking (Helmen method)
Bandbeschichtete Metalle - Prüfverfahren - Teil 14: Kreiden (Verfahren nach Helmen)
Tôles prélaquées - Méthodes d'essai - Partie 14: Farinage (méthode Helmen)
Ta slovenski standard je istoveten z: prEN 13523-14
ICS:
17.040.20 Lastnosti površin Properties of surfaces
25.220.60 Organske prevleke Organic coatings
oSIST prEN 13523-14:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 13523-14:2022
---------------------- Page: 2 ----------------------
oSIST prEN 13523-14:2022
DRAFT
EUROPEAN STANDARD
prEN 13523-14
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2022
ICS 25.220.60 Will supersede EN 13523-14:2014
English Version
Coil coated metals - Test methods - Part 14: Chalking
(Helmen method)
Tôles prélaquées - Méthodes d'essai - Partie 14: Bandbeschichtete Metalle - Prüfverfahren - Teil 14:
Farinage (méthode Helmen) Kreiden (Verfahren nach Helmen)
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 139.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13523-14:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 13523-14:2022
prEN 13523-14:2022 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 6
5 Apparatus . 6
6 Sampling . 6
7 Test specimens . 6
8 Procedure . 6
8.1 General. 6
8.2 Checking the adhesive tape . 6
8.3 Calibration . 6
8.4 Measurement . 7
9 Expression of results . 7
10 Precision . 7
11 Test report . 7
Bibliography . 8
2
---------------------- Page: 4 ----------------------
oSIST prEN 13523-14:2022
prEN 13523-14:2022 (E)
European foreword
This document (prEN 13523-14:2022) has been prepared by Technical Committee CEN/TC 139 “Paints
and varnishes”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13523-14:2014.
In comparison with the previous edition, the following technical modifications have been made:
a) the description of the test apparatus has been changed;
b) the text has been editorially revised and the normative references have been updated.
EN 13523, Coil coated metals — Test methods, consists of the following parts:
— Part 0: General introduction
— Part 1: Film thickness
— Part 2: Gloss
— Part 3: Colour difference and metamerism — Instrumental comparison
— Part 4: Pencil hardness
— Part 5: Resistance to rapid deformation (impact test)
— Part 6: Adhesion after indentation (cupping test)
— Part 7: Resistance to cracking on bending (T-bend test)
— Part 8: Resistance to salt spray (fog)
— Part 9: Resistance to water immersion
— Part 10: Resistance to fluorescent UV radiation and water condensation
— Part 11: Resistance to solvents (rubbing test)
— Part 12: Resistance to scratching
— Part 13: Resistance to accelerated ageing by the use of heat
— Part 14: Chalking (Helmen method)
— Part 16: Resistance to abrasion
— Part 17: Adhesion of strippable films
— Part 18: Resistance to staining
— Part 19: Panel design and method of atmospheric exposure testing
3
---------------------- Page: 5 ----------------------
oSIST prEN 13523-14:2022
prEN 13523-14:2022 (E)
— Part 20: Foam adhesion
— Part 21: Evaluation of outdoor exposed panels
— Part 22: Colour difference — Visual comparison
— Part 23: Resistance to humid atmospheres containing sulfur dioxide
— Part 24: Resistance to blocking and pressure marking
— Part 25: Resistance to humid
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.