Household and similar electrical appliances - Safety -- Part 2-80: Particular requirements for fans (IEC 60335-2-80:2015)

IEC 60335-2-80:2015 is available as IEC 60335-2-80:2015 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60335-2-80:2015(E) deals with the safety of electric fans for household and similar purposes, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. Examples of fans that are     within the  scope of this standard are ceiling fans;  duct fans;  partition fans;   pedestal fans  and table fans. This standard also  applies to  separate  controls supplied with fans.  Appliances not intended for  normal household use   but which  nevertheless may be a  source of danger to the  public, such as appliances intended to be used by laymen in shops, in light industry      and on farms, are within  the  scope of this standard. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not   take into account  persons (including children)  whose physical, sensory or mental capabilities;   or lack  of experience and knowledge prevents  them from using the appliance safely without supervision or  instruction.     It also does not take  into account  children playing with the appliance.
It was established on the basis of the fifth edition (2010) of that standard. This third edition cancels and replaces the second edition published in 2002, its Amendment 1 (2007) and its Amendment 2 (2011). It constitutes a technical revision. The principal changes in this edition as compared with the second edition of IEC 60335-2-80 are as follows (minor changes are not listed):
- added definition for ceiling fan suspension system (3.102);
- added instructions for ceiling fan maintenance (7.12);
- added instructions for ceiling fan installation (7.12.1);
- added entrapment assessment criteria for table and pedestal fan with a fan head that oscillates in the up-down direction (20.102);
- added requirements for insulation of pre-installed internal wiring used to supply attached luminaires (22.101);
- added suspension system failure protection requirements for ceiling fans (22.102);
- added motor brush wear requirements (27.3).
The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this standard be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of its publication.
Key words: Fans, Duct fans, Pedestal fans, Ceiling fans, Partition fans, Table fans

Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-80: Besondere Anforderungen für Ventilatoren (IEC 60335-2-80:2015)

Appareils électrodomestiques et analogues – Sécurité – Partie 2-80: Exigences particulières pour les ventilateurs (IEC 60335-2-80:2015)

L'IEC 60335-2-80:2015 traite de la sécurité des ventilateurs électriques pour usages domestiques et analogues dont la tension assignée n'est pas supérieure à 250 V pour les appareils monophasés et 480 V pour les autres appareils.
Des exemples de ventilateurs compris dans le domaine d'application de la présente norme sont:
- les ventilateurs de plafond;
- les ventilateurs de conduit;
- les ventilateurs de cloison;
- les ventilateurs à colonne;
- les ventilateurs de table.
Cette norme s'applique également aux dispositifs de commande fournis avec les ventilateurs.
Les appareils non destinés à un usage domestique normal, mais qui peuvent néanmoins constituer une source de danger pour le public, tels que les appareils destinés à être utilisés dans des magasins, chez des artisans et dans des fermes, sont compris dans le domaine d'application de la présente norme.
Dans la mesure du possible, la présente norme traite des dangers courants présentés par les appareils, encourus par tous les individus à l'intérieur et autour de l'habitation. Cependant, la présente norme ne tient pas compte en général:
- des personnes (y compris des enfants) dont:
    - les capacités physiques, sensorielles ou mentales; ou
    - le manque d'expérience et de connaissances
  les empêchent d'utiliser l'appareil en toute sécurité sans surveillance ou instruction;
- de l'utilisation de l'appareil comme jouet par des enfants.
L'attention est attirée sur le fait que:
- pour les appareils destinés à être utilisés dans des véhicules ou à bord de navires ou d'avions, des exigences supplémentaires peuvent être nécessaires;
- dans de nombreux pays, des exigences supplémentaires sont spécifiées par les autorités sanitaires nationales, les organismes nationaux en charge de la protection des travailleurs et les organismes analogues.
La présente norme ne s'applique pas:
- aux appareils prévus exclusivement pour des usages industriels;
- aux appareils destinés à être utilisés dans des locaux présentant des conditions particulières, telles que la présence d'une atmosphère corrosive ou explosive (poussière, vapeur ou gaz);
- aux ventilateurs incorporés dans d'autres appareils.
Cette troisième édition annule et remplace la deuxième édition parue en 2002, y compris son Amendement 1 (2004) et son Amendement 2 (2008). Elle constitue une révision technique.
Les principales modifications apportées à la présente édition par rapport à la deuxième édition de l'IEC 60335­2­80 sont les suivantes (les modifications mineures ne sont pas citées):
- ajout de la définition du terme système de suspension de ventilateur de plafond (3.102);
- ajout d'instructions relatives à l'entretien des ventilateurs de plafond (7.12);
- ajout d'instructions relatives à l'installation des ventilateurs de plafond (7.12.1);
- ajout de critères d'évaluation du piégeage pour les ventilateurs de table et les ventilateurs à colonne dotés d'une tête oscillant de haut en bas (20.102);
- ajout d'exigences relatives à l'isolation des conducteurs internes préinstallés utilisés pour alimenter les luminaires fixés (22.101);
- ajout d'exigences relatives à la protection contre les défaillances des systèmes de suspension pour les ventilateurs de plafond (22.102);
- ajout d'exigences relatives à l

Gospodinjski in podobni električni aparati - Varnost - 2-80. del: Posebne zahteve za ventilatorje (IEC 60335-2-80:2015)

General Information

Status
Published
Publication Date
26-Nov-2024
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
21-Nov-2024
Due Date
26-Jan-2025
Completion Date
27-Nov-2024

Relations

Buy Standard

Standard
EN IEC 60335-2-80:2025 - BARVE
English language
27 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2025
Nadomešča:
SIST EN 60335-2-80:2003
SIST EN 60335-2-80:2003/A1:2004
SIST EN 60335-2-80:2003/A2:2009
Gospodinjski in podobni električni aparati - Varnost - 2-80. del: Posebne zahteve
za ventilatorje (IEC 60335-2-80:2015)
Household and similar electrical appliances - Safety -- Part 2-80: Particular requirements
for fans (IEC 60335-2-80:2015)
Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-80:
Besondere Anforderungen für Ventilatoren (IEC 60335-2-80:2015)
Appareils électrodomestiques et analogues – Sécurité – Partie 2-80: Exigences
particulières pour les ventilateurs (IEC 60335-2-80:2015)
Ta slovenski standard je istoveten z: EN IEC 60335-2-80:2024
ICS:
13.120 Varnost na domu Domestic safety
23.120 Zračniki. Vetrniki. Klimatske Ventilators. Fans. Air-
naprave conditioners
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60335-2-80

NORME EUROPÉENNE
EUROPÄISCHE NORM November 2024
ICS 13.120; 23.120 Supersedes EN 60335-2-80:2003; EN 60335-2-
80:2003/A1:2004; EN 60335-2-80:2003/A2:2009
English Version
Household and similar electrical appliances - Safety - Part 2-80:
Particular requirements for fans
(IEC 60335-2-80:2015)
Appareils électrodomestiques et analogues - Sécurité - Sicherheit elektrischer Geräte für den Hausgebrauch und
Partie 2-80: Exigences particulières pour les ventilateurs ähnliche Zwecke - Teil 2-80: Besondere Anforderungen für
(IEC 60335-2-80:2015) Ventilatoren
(IEC 60335-2-80:2015)
This European Standard was approved by CENELEC on 2024-08-07. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60335-2-80:2024 E

European foreword
This document (EN IEC 60335-2-80:2024) consists of the text of document IEC 60335-2-80:2015,
prepared by IEC/TC 61 "Safety of household and similar electrical appliances".
The following dates are fixed:
• latest date by which this document has (dop) 2025-05-15
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2027-11-15
standards conflicting with this document
have to be withdrawn
This document supersedes EN 60335-2-80:2003 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document is read in conjunction with EN IEC 60335-2-80:2024/A11:2024.
This document has been prepared under a standardization request addressed to CENELEC by the
European Commission. The Standing Committee of the EFTA States subsequently approves these
requests for its Member States.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60335-2-80:2015 was approved by CENELEC as a European
Standard without any modification.

IEC 60335-2-80 ®
Edition 3.0 2015-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Household and similar electrical appliances – Safety –

Part 2-80: Particular requirements for fans

Appareils électrodomestiques et analogues – Sécurité –

Partie 2-80: Exigences particulières pour les ventilateurs

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 13.120; 23.120 ISBN 978-2-8322-6245-0

– 2 – IEC 60335-2-80:2015 © IEC 2015
CONTENTS
FOREWORD . 4
INTRODUCTION . 7
1 Scope . 8
2 Normative references . 9
3 Terms and definitions . 9
4 General requirement . 9
5 General conditions for the tests . 9
6 Classification . 10
7 Marking and instructions . 10
8 Protection against access to live parts . 11
9 Starting of motor-operated appliances . 11
10 Power input and current . 11
11 Heating . 12
12 Void . 12
13 Leakage current and electric strength at operating temperature . 12
14 Transient overvoltages . 12
15 Moisture resistance . 12
16 Leakage current and electric strength . 12
17 Overload protection of transformers and associated circuits . 12
18 Endurance . 12
19 Abnormal operation . 13
20 Stability and mechanical hazards . 13
21 Mechanical strength . 14
22 Construction . 14
23 Internal wiring . 16
24 Components . 16
25 Supply connection and external flexible cords . 16
26 Terminals for external conductors . 16
27 Provision for earthing . 16
28 Screws and connections . 17
29 Clearances, creepage distances and solid insulation . 17
30 Resistance to heat and fire . 17
31 Resistance to rusting . 17
32 Radiation, toxicity and similar hazards . 17
Annexes . 24
Bibliography . 25

Figure 101 – Subclause 22.102.1 – Example . 18
Figure 102 – Test pin . 19
Figure 103 – Subclause 22.102.2 – Example . 20
Figure 104 – Subclause 22.102.3 – Example . 21

IEC 60335-2-80:2015 © IEC 2015 – 3 –
Figure 105 – Subclause 22.102.4 – Example . 22
Figure 106 – Subclause 22.102.5 – Example 1 . 23

– 4 – IEC 60335-2-80:2015 © IEC 2015
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES –
SAFETY –
Part 2-80: Particular requirements for fans

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall n
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.