iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 15553:2022/oprA1:2024

(Amendment)

Petroleum products and related materials - Determination of hydrocarbon types - Fluorescent indicator adsorption method

Petroleum products and related materials - Determination of hydrocarbon types - Fluorescent indicator adsorption method

This document specifies a fluorescent indicator adsorption method for the determination of hydrocarbon types over the concentration ranges from 5 % (V/V) to 99 % (V/V) aromatic hydrocarbons, 0,3 % (V/V) to 55 % (V/V) olefins, and 1 % (V/V) to 95 % (V/V) saturated hydrocarbons in petroleum fractions that distil below 315 °C. This method can apply to concentrations outside these ranges, but the precision has not been determined.
When samples containing oxygenated blending components are analysed, the hydrocarbon type results can be reported on an oxygenate-free basis or, when the oxygenate content is known, the results can be corrected to a total-sample basis.
This test method is applicable to full boiling range products. Cooperative data have established that the precision statement does not apply to petroleum fractions with narrow boiling ranges near the 315 °C limit. Such samples are not eluted properly, and results are erratic.
It does not apply to samples containing dark-coloured components that interfere with reading the chromatographic bands that cannot be analysed.
NOTE 1   The oxygenated blending components methanol, ethanol, tert-butyl methyl ether (MTBE), methyl tert-pentyl ether (TAME) and tert-butyl ethyl ether (ETBE) do not interfere with the determination of hydrocarbon types at concentrations normally found in commercial petroleum blends. These oxygenated compounds are not detected since they elute with the alcohol desorbent. The effects of other oxygenated compounds are individually verified.
NOTE 2   For the purposes of this document, the terms “% (m/m)” and “% (V/V)” are used to represent respectively the mass fraction and the volume fraction.
WARNING — The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Mineralölerzeugnisse und verwandte Produkte - Bestimmung der Kohlenwasserstofftypen - Adsorptionsverfahren mit Fluoreszenz-Indikator

Produits pétroliers et produits connexes - Détermination des groupes d'hydrocarbures - Méthode par adsorption en présence d'indicateur fluorescent

Naftni proizvodi in sorodni materiali - Določevanje vrste ogljikovodikov - Adsorpcijska metoda s fluorescenčnim indikatorjem

General Information

Status
Not Published
Public Enquiry End Date
02-May-2024
ICS
75.080 - Petroleum products in general
Technical Committee
NAD - Petroleum products, lubricants and related products
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
29-Feb-2024
Due Date
18-Jul-2024
Ref Project
EN 15553:2021/prA1 - Petroleum products and related materials - Determination of hydrocarbon types - Fluorescent indicator adsorption method

Relations

Amends
SIST EN 15553:2022 - Petroleum products and related materials - Determination of hydrocarbon types - Fluorescent indicator adsorption method
Effective Date
01-Apr-2024

Buy Standard

EN 15553:2022/oprA1:2024EN 15553:2022/oprA1:2024
PreviousNext
Draft
EN 15553:2022/oprA1:2024
English language
5 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 15553:2022/oprA1:2024
01-april-2024
Naftni proizvodi in sorodni materiali - Določevanje vrste ogljikovodikov -
Adsorpcijska metoda s fluorescenčnim indikatorjem
Petroleum products and related materials - Determination of hydrocarbon types -
Fluorescent indicator adsorption method
Mineralölerzeugnisse und verwandte Produkte - Bestimmung der
Kohlenwasserstofftypen - Adsorptionsverfahren mit Fluoreszenz-Indikator
Produits pétroliers et produits connexes - Détermination des groupes d'hydrocarbures -
Méthode par adsorption en présence d'indicateur fluorescent
Ta slovenski standard je istoveten z: EN 15553:2021/prA1
ICS:
75.080 Naftni proizvodi na splošno Petroleum products in
general
SIST EN 15553:2022/oprA1:2024 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 15553:2022/oprA1:2024

---------------------- Page: 2 ----------------------
SIST EN 15553:2022/oprA1:2024


DRAFT
EUROPEAN STANDARD
EN 15553:2021
NORME EUROPÉENNE

EUROPÄISCHE NORM
prA1
April 2024
ICS 75.080
English Version

Petroleum products and related materials - Determination
of hydrocarbon types - Fluorescent indicator adsorption
method
Produits pétroliers et produits relates - Détermination Mineralölerzeugnisse und verwandte Produkte -
des types hydrocarbonates - Méthode par adsorption Bestimmung von Kohlenwasserstofftypen -
d'indicatoire fluorescents Fluoreszenz-Indikator-Adsorptionsprüfung
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 19.

This draft amendment A1, if approved, will modify the European Standard EN 15553:2021. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to sub
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 18335:2024(Main)
Petroleum products and related products - Determination of kinematic viscosity by calculation from the measured dynamic viscosity and density - Method by constant pressure viscometer (ISO 18335:2024)
EN ISO 18335:2024

This document specifies a procedure for determining dynamic viscosity, η, and density, ρ, for the calculation
of kinematic viscosity, ν, of middle distillate fuels, fatty acid methyl ester fuels (FAME) and mixtures thereof,
up to 60 % with middle distillate fuels, and lubricating oils (e.g. base oils, formulated oils), and synthetics,
using a constant pressure viscometer. The range of kinematic viscosities covered in this test method is from
0,5 mm2/s to 2 000 mm2/s, with precision at 40 °C from 1,0 mm2/s to 1 286 mm2/s, and precision at 100 °C
from 3,0 mm2/s to 157 mm2/s.
The result obtained using the procedure described in this document depends on the rheological behaviour
of the sample. This document is predominantly applicable to liquids whose shear stress and shear rate are
proportional (Newtonian flow behaviour). However, if the viscosity changes significantly with the shear
rate, comparison with other measuring methods is only permissible at similar shear rates.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 4259-5:2024(Main)
Petroleum and related products - Precision of measurement methods and results - Part 5: Statistical assessment of agreement between two different measurement methods that claim to measure the same property (ISO 4259-5:2023)
EN ISO 4259-5:2024

This document specifies statistical methodology for assessing the expected agreement between two
test methods that purport to measure the same property of a material, and for deciding if a simple
linear bias correction can further improve the expected agreement.
This document is applicable for analytical methods which measure quantitative properties of petroleum
or petroleum products resulting from a multi-sample-multi-lab study (MSMLS). These types of studies
include but are not limited to interlaboratory studies (ILS) meeting the requirements of ISO 4259-1
or equivalent, and proficiency testing programmes (PTP) meeting the requirements of ISO 4259-3 or
equivalent.
The methodology specified in this document establishes the limiting value for the difference between
two results where each result is obtained by a different operator using different apparatus and two
methods X and Y, respectively, on identical material. One of the methods (X or Y) has been appropriately
bias-corrected to agree with the other in accordance with this practice. This limit is designated as the
between-methods reproducibility. This value is expected to be exceeded with a probability of 5 % under
the correct and normal operation of both test methods due to random variation.
NOTE Further conditions for application of this methodology are given in 5.1 and 5.2.

  • Standard
    56 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 3838:2004/A1:2024(Amendment)
Crude petroleum and liquid or solid petroleum products - Determination of density or relative density - Capillary-stoppered pyknometer and graduated bicapillary pyknometer methods - Amendment 1 (ISO 3838:2004/Amd 1:2023)
EN ISO 3838:2004/A1:2023
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 3104:2024(Main)
Petroleum products - Transparent and opaque liquids - Determination of kinematic viscosity and calculation of dynamic viscosity (ISO 3104:2023)
EN ISO 3104:2023

This document specifies Procedure A, using manual glass viscometers, and Procedure B, using glass capillary viscometers in an automated assembly, for the determination of the kinematic viscosity, ν, of liquid petroleum products, both transparent and opaque, by measuring the time for a volume of liquid to flow under gravity through a calibrated glass capillary viscometer. The dynamic viscosity, η, is obtained by multiplying the measured kinematic viscosity by the density, ρ, of the liquid. The range of kinematic viscosities covered in this test method is from 0,2 mm2/s to 300 000 mm2/s over the temperature range –20 °C to +150 °C. The products it is applicable to contain kerosene, diesel fuels, biodiesel fuels, and biodiesel fuel blends.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15522-2:2023(Main)
Oil spill identification - Petroleum and petroleum related products - Part 2: Analytical method and interpretation of results based on GC-FID and GC-low resolution-MS analyses
EN 15522-2:2023

This document specifies a method to identify and compare the compositional characteristics of oil
samples. Specifically, it describes the detailed analytical and data processing methods for identifying the
characteristics of spill samples and establishing their correlation to suspected source oils. Even when
samples or data from suspected sources are not available for comparison, establishing the specific nature
(e.g. refined petroleum, crude oil, waste oil, etc.) of the spilled oil still helps to constrain the possible
source(s).
This methodology is restricted to petroleum related products containing a significant proportion of
hydrocarbon-components with a boiling point above 150 °C. Examples are: crude oils, higher boiling
condensates, diesel oils, residual bunker or heavy fuel oils, lubricants, and mixtures of bilge and sludge
samples, as well as distillate fuels and blends. While the specific analytical methods are perhaps not
appropriate for lower boiling oils (e.g. kerosene, jet fuel, or gasoline), the general concepts described in
this methodology, i.e. statistical comparison of weathering-resistant diagnostic ratios, are applicable in
spills involving these kinds of oils.
Paraffin products (e.g. waxes, etc.) are outside the scope of this method because too many compounds
are removed during the production process [37] to correctly distinguish them from each other. However,
the method can be used to identify the type of product involved.
Although not directly intended for identifying oil recovered from groundwater, vegetation,
wildlife/tissues, soil, or sediment matrices, they are not precluded. However, caution is needed as
extractable compounds can be present in these matrices that alter and/or contribute additional
compounds compared to the source sample. If unrecognized, the contribution from the matrix can lead
to false “non-matches”. It is therefore advisable to analyse background sample(s) of the matrix that
appear unoiled.
When analysing “non-oil” matrices additional sample preparation (e.g. clean-up) is often required prior
to analysis and the extent to which the matrix affects the correlation achieved is to be considered.
Whether the method is applicable for a specific matrix depends upon the oil concentration compared to
the “matrix concentration”. In matrices containing high concentrations of oil, a positive match can still be
concluded. In matrices containing lower concentrations of oil, a false “non-match” or an “inconclusive
match” can result from matrix effects. Evaluation of possible matrix effects is beyond the scope of this
document.

  • Standard
    219 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    194 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15522-1:2023(Main)
Oil spill identification - Petroleum and petroleum related products - Part 1: Sampling
EN 15522-1:2023

EN 15522-1 provides guidance on taking and handling samples, that are collected as part of an investigation into the likely source of a crude oil or petroleum product spill into a marine or aquatic environment. Guidance is given on taking samples from both the spill and its potential source.
Mostly, oil sampling is part of legal procedures and has to be treated like any other preservation of evidence (legal sampling). If samples are to be used in connection with legal proceedings, this document should be read in conjunction with any documents issued by the regulatory authorities in the country or countries in question where the spill has occurred.
Taking samples may involve hazardous materials, operations and equipment.
This document is not intended to address all the safety and health aspects associated with the guidance given. It is the responsibility of the user to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note: Most countries have special trained teams to take samples on board of ships. As police officer or law enforcer don’t take unnecessary risks and ask assistance from such a team when available.
For the sake of clarity, the word ‘oil’ is used throughout this document. It can equally refer to crude oil, a petroleum product or mixtures of such.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 3679:2023(Main)
Determination of flash point - Method for flash no-flash and flash point by small scale closed cup tester (ISO 3679:2022)
EN ISO 3679:2022

This document describes three procedures (A, B and C) covering determinations of flash no-flash and flash point.
Rapid equilibrium procedures A and B are applicable to flash no-flash and flash point tests of paints, including water-borne paints, varnishes, binders for paints and varnishes, adhesives, solvents, petroleum products including aviation turbine, diesel and kerosene fuels, fatty acid methyl esters and related products over the temperature range –30 °C to 300 °C. The rapid equilibrium procedures are used to determine whether a product will or will not flash at a specified temperature (flash no-flash procedure A) or the flash point of a sample (procedure B). When used in conjunction with the flash detector (A.1.6), this document is also suitable to determine the flash point of fatty acid methyl esters (FAME). The validity of the precision is given in Table 2.
Non-equilibrium procedure C is applicable to petroleum products including aviation turbine, diesel and kerosine fuels, and related petroleum products, over the temperature range –20 °C to 300 °C. The non-equilibrium procedure is automated to determine the flash point. Precision has been determined over the range 40 °C to 135 °C.
For specifications and regulations, procedures A or B are routinely used (see 10.1.1).

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 13736:2021/A1:2022(Amendment)
Determination of flash point - Abel closed-cup method - Amendment 1: Bias statement update (ISO 13736:2021/Amd 1:2022)
EN ISO 13736:2021/A1:2022
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 4259-4:2022(Main)
Petroleum and related products - Precision of measurement methods and results - Part 4: Use of statistical control charts to validate 'in-statistical-control' status for the execution of a standard test method in a single laboratory (ISO 4259-4:2021)
EN ISO 4259-4:2022

This document specifies the methodology to determine if a laboratory is in control in the execution of a standard test method. By using statistical control charts and following this document the 'in-statistical-control' status is established and validated. In-statistical-control means the test results produced by the lab on control samples are reasonably consistent with expectation over time; with random variation scattered around a stable expected centre due to common causes only
This document explicitly defines ‘site precision’ conditions as  single apparatus, multi-operators, over a long time horizon. It specifies control charts that are most appropriate for ISO TC28 test methods where the dominant common cause variation is associated with the long term, multiple operator conditions as described by "site precision" conditions. The control charts specified for determination of in-statistical-control are: Individual (I), Moving Range of 2 (MR2), Exponentially Weighted Moving Average (EWMA), and zone-based run rules (commonly known as Western Electric (WE)run rules.
The procedures in this document have been designed specifically for petroleum and petroleum related products, which are normally considered as homogeneous and for test methods which show normality in obtaining their results. However, the procedures described in this document can also be applied to other types of homogeneous products and test methods.

  • Standard
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15553:2022(Main)
Petroleum products and related materials - Determination of hydrocarbon types - Fluorescent indicator adsorption method
EN 15553:2021

This European Standard specifies a fluorescent indicator adsorption method for the determination of hydrocarbon types over the concentration ranges from 5 % (V/V) to 99 % (V/V) aromatic hydrocarbons, 0,3 % (V/V) to 55 % (V/V) olefins, and 1 % (V/V) to 95 % (V/V) saturated hydrocarbons in petroleum fractions that distil below 315 ºC. This method may apply to concentrations outside these ranges, but the precision has not been determined.
When samples containing oxygenated blending components are analysed, the hydrocarbon type results can be reported on an oxygenate-free basis or, when the oxygenate content is known, the results can be corrected to a total-sample basis.
This test method is for use with full boiling range products. Cooperative data have established that the precision statement does not apply to petroleum fractions with narrow boiling ranges near the 315 °C limit. Such samples are not eluted properly, and results are erratic.
Samples containing dark-coloured components that interfere with reading the chromatographic bands cannot be analysed.
NOTE 1   The oxygenated blending components methanol, ethanol, tert-butyl methyl ether (MTBE), methyl tert-pentyl ether (TAME) and tert-butyl ethyl ether (ETBE) do not interfere with the determination of hydrocarbon types at concentrations normally found in commercial petroleum blends. These oxygenated compounds are not detected since they elute with the alcohol desorbent. The effects of other oxygenated compounds should be individually verified.
NOTE 2   For the purposes of this European Standard, the terms “% (m/m)” and “% (V/V)” are used to represent respectively the mass fraction and the volume fraction.
WARNING — The use of this European Standard may involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day