SIST EN ISO 23429:2004

SLOVENSKI STANDARD
SIST EN ISO 23429:2004
01-junij-2004
Kontrola notranje šestrobe luknje s kalibrom (ISO 23492:2004)
Gauging of hexagon sockets (ISO 23429:2004)
Lehrung von Innensechskanten (ISO 23429:2004)
Calibrage des six pans creux (ISO 23429:2004)
Ta slovenski standard je istoveten z: EN ISO 23429:2004
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST EN ISO 23429:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 23429:2004

---------------------- Page: 2 ----------------------

SIST EN ISO 23429:2004
EUROPEAN STANDARD
EN ISO 23429
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2004
ICS 21.060.10
English version
Gauging of hexagon sockets (ISO 23429:2004)
Calibrage des six pans creux (ISO 23429:2004) Lehrung von Innensechskanten (ISO 23429:2004)
This European Standard was approved by CEN on 10 December 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 23429:2004: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 23429:2004
EN ISO 23429:2004 (E)
CORRECTED  2004-03-03
Foreword
This document (EN ISO 23429:2004) has been prepared by Technical Committee ISO/TC 2
"Fasteners" in collaboration with Technical Committee CEN/TC 185 "Threaded and non-
threaded mechanical fasteners and accessories", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by July 2004, and conflicting national standards
shall be withdrawn at the latest by July 2004.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 23429:2004 has been approved by CEN as EN ISO 23429:2004 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
2

---------------------- Page: 4 ----------------------

SIST EN ISO 23429:2004
EN ISO 23429:2004 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 4759-1 2000 Tolerances for fasteners - Part 1: EN ISO 4759-1 2000
Bolts, screws, studs and nuts -
Product grades A, B and C
3

---------------------- Page: 5 ----------------------

SIST EN ISO 23429:2004

---------------------- Page: 6 ----------------------

SIST EN ISO 23429:2004
INTERNATIONAL ISO
STANDARD 23429
First edition
2004-01-15
Gauging of hexagon sockets
Calibrage des six pans creux

Reference number
ISO 23429:2004(E)
©
ISO 2004

---------------------- Page: 7 ----------------------

SIST EN ISO 23429:2004
ISO 23429:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unl
...