Aerospace series - Rivets, solid, universal head, in corrosion resisting steel FE-PA11, passivated, inch based series

This standard specifies the characteristics of solid rivets, universal head, in corrosion resisting steel FE-PA11, passivated, inch based series, for maximum operating temperature 700 °C.

Luft- und Raumfahrt - Vollniete, mit Universalkopf, aus korrosionsbeständigem Stahl FE-PA11, passiviert, Zoll-Reihe

Diese Norm legt die Eigenschaften von Vollnieten, mit Universalkopf, aus korrosionsbeständigem Stahl FE-PA11, passiviert, Zoll-Reihe, zur Verwendung bei Temperaturen bis 700 °C, fest.

Série aérospatiale - Rivets ordinaires, a tete ronde aplatie, en acier résistant a la corrosion FE-PA11, passivés, série base inches

La présente norme spécifie les caractéristiques des rivets ordinaires, à tête ronde aplatie, en acier résistant à la corrosion FE-PA11, passivés, série base inches, pour température maximale d'utilisation 700 °C.

Aerospace series - Rivets, solid, universal head, in corrosion resisting steel FE-PA11, passivated, inch based series

General Information

Status
Published
Publication Date
31-Dec-2000
ICS
49.030.60 - Rivets
Technical Committee
SS SPL - Technical Board for the general field
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Jan-2001
Due Date
01-Jan-2001
Completion Date
01-Jan-2001
Ref Project
EN 3135:1996 - Aerospace series - Rivets, solid, universal head, in corrosion resisting steel FE-PA11, passivated, inch based series

Overview

EN 3135:1996 is a CEN aerospace standard that defines the characteristics of solid rivets, universal head, made from corrosion resisting steel FE-PA11, passivated, in an inch-based series. The standard is intended for use in aerospace applications and establishes suitability for service up to a maximum operating temperature of 700 °C. EN 3135 supports consistent specification, procurement, manufacture and quality control of this specific type of aerospace rivet.

Key Topics

The standard focuses on the following technical aspects (typical content areas covered by EN aerospace fastener standards):

  • Rivet type and head form: solid rivets with a universal (rounded/flattened) head geometry suitable for aerospace structures.
  • Material designation: corrosion resisting steel identified as FE-PA11, with requirement for passivation to improve surface corrosion resistance.
  • Dimensional series: inch-based sizes and associated dimensional tolerances for hole fit and rivet length.
  • Operating conditions: suitability and performance up to 700 °C maximum operating temperature.
  • Manufacturing and finish: requirements for mechanical processing, heat treatment and passivation processes to ensure consistent corrosion resistance and integrity.
  • Inspection and acceptance: provisions for dimensional checks, surface condition, marking and testing to verify compliance.

(Note: EN 3135 sets characteristics; manufacturers and users refer to the complete standard for detailed tables and acceptance criteria.)

Applications

EN 3135 is directly applicable where high-temperature, corrosion-resistant solid rivets are required in aerospace structures and components:

  • Aircraft and engine assemblies where temperature resistance up to 700 °C is needed.
  • Structural joints in airframes, engine casings, ducts and thermal protection systems using inch-based fasteners.
  • Use by aerospace designers, fastener manufacturers, procurement specialists, quality engineers, and maintenance organizations specifying or verifying rivet conformity.
  • Suppliers who must produce rivets to recognized aerospace standards for qualification and traceability.

Related Standards

  • Other EN aerospace fastener standards covering rivets, bolts, nuts, material specifications, testing methods and installation practices are commonly used together with EN 3135 to establish complete procurement and inspection requirements.
  • Refer to national adoptions (e.g., SIST EN 3135) for local publication details and official translations.

Keywords: EN 3135, solid rivets, universal head, corrosion resisting steel FE-PA11, passivated rivets, inch based series, aerospace rivets, fastener standard, 700 °C.

Frequently Asked Questions

SIST EN 3135:2001 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Aerospace series - Rivets, solid, universal head, in corrosion resisting steel FE-PA11, passivated, inch based series". This standard covers: This standard specifies the characteristics of solid rivets, universal head, in corrosion resisting steel FE-PA11, passivated, inch based series, for maximum operating temperature 700 °C.

This standard specifies the characteristics of solid rivets, universal head, in corrosion resisting steel FE-PA11, passivated, inch based series, for maximum operating temperature 700 °C.

SIST EN 3135:2001 is classified under the following ICS (International Classification for Standards) categories: 49.030.60 - Rivets. The ICS classification helps identify the subject area and facilitates finding related standards.

SIST EN 3135:2001 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Rivets, solid, universal head, in corrosion resisting steel FE-PA11, passivated, inch based seriesLuft- und Raumfahrt - Vollniete, mit Universalkopf, aus korrosionsbeständigem Stahl FE-PA11, passiviert, Zoll-ReiheSérie aérospatiale - Rivets ordinaires, a tete ronde aplatie, en acier résistant a la corrosion FE-
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

Loading comments...