SIST EN ISO 11393-3:2018

SLOVENSKI STANDARD
01-december-2018
1DGRPHãþD
SIST EN 381-3:1996
9DURYDOQDREOHND]DXSRUDEQLNHURþQLKYHULåQLKåDJGHO3UHVNXVQHPHWRGH]D
REXWHY,62
Protective clothing for users of hand-held chainsaws - Part 3: Test methods for footwear
(ISO 11393-3:2018)
Schutzkleidung für die Benutzer von handgeführten Kettensägen - Teil 3: Prüfverfahren
für Schuhwerk (ISO 11393-3:2018)
Vêtements de protection pour utilisateurs de scies à chaîne tenues à la main - Partie 3:
Méthodes d'essai pour chaussures (ISO 11393-3:2018)
Ta slovenski standard je istoveten z: EN ISO 11393-3:2018
ICS:
13.340.50 Varovanje nog in stopal Leg and foot protection
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 11393-3
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2018
EUROPÄISCHE NORM
ICS 13.340.50 Supersedes EN 381-3:1996
English Version
Protective clothing for users of hand-held chainsaws - Part
3: Test methods for footwear (ISO 11393-3:2018)
Vêtements de protection pour utilisateurs de scies à Schutzkleidung für die Benutzer von handgeführten
chaîne tenues à la main - Partie 3: Méthodes d'essai Kettensägen - Teil 3: Prüfverfahren für Schuhwerk (ISO
pour chaussures (ISO 11393-3:2018) 11393-3:2018)
This European Standard was approved by CEN on 12 August 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11393-3:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 11393-3:2018) has been prepared by Technical Committee ISO/TC 94
"Personal safety -- Personal protective equipment" in collaboration with Technical Committee CEN/TC
162 “Protective clothing including hand and arm protection and lifejackets” the secretariat of which is
held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 381-3:1996.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11393-3:2018 has been approved by CEN as EN ISO 11393-3:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 11393-3
Second edition
2018-09
Protective clothing for users of hand-
held chainsaws —
Part 3:
Test methods for footwear
Vêtements de protection pour utilisateurs de scies à chaîne tenues à
la main —
Partie 3: Méthodes d'essai pour chaussures
Reference number
ISO 11393-3:2018(E)
©
ISO 2018
ISO 11393-3:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

ISO 11393-3:2018(E)
Contents Page
Foreword .iv
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test specimens. 1
5 Checking of protective area . 2
5.1 Sizing body for laced footwear . 2
5.2 Procedure . 2
6 Testing resistance to cutting . 3
6.1 Apparatus . 3
6.1.1 Test rig . 3
6.1.2 Footwear mounting devices . 3
6.1.3 Material for filling footwear . 3
6.2 Test procedure . 4
6.2.1 General. 4
6.2.2 Cuts on vamp area . 5
6.2.3 Cuts on throat area . 6
6.2.4 Cuts on leg region . 7
6.2.5 Additional cuts for footwear with non-steel toecaps . 9
7 Test report . 9
ISO 11393-3:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by the European Committee for Standardization (CEN) Technical
Committee CEN/TC 162, Protective clothing including hand and arm protection and lifejackets, in
collaboration with ISO Technical Committee TC 94, Personal safety — Personal protective equipment,
Subcommittee SC 13, Protective clothing, in accordance with the agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 11393-3:1999), which has been technically
revised. The main changes compared to the previous edition are as follows:
— in the Introduction, the term “hand-held chainsaws primarily constructed for cutting wood” has
been added;
— the normative references have been updated;
— the term and definition 3.1 has been added;
— in Clause 4, the definition has been adapted to 6.2;
— in Clause 5, the definition and normative reference has been specified;
— in 6.1.2.2, 6.2.1, 6.2.2, 6.2.3, 6.2.4 and Clause 7, definitions have been specified;
— in 6.1.3, a new comprising procedure has been defined;
— in 6.2.1, the total number of cuts has been enlarged, “protection class” has been renamed as “level”
and “class 0” has been deleted;
— in 6.2.4, an alternative system for fastening the footwear to the test rig has been added;
— in 6.2.5, the definition “non-steel” has been used following ISO 17249.
A list of all parts in the ISO 11393 series can be found on the ISO website.
iv © ISO 2018 – All rights reserved

ISO 11393-3:2018(E)
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
ISO 11393-3:2018(E)
Introduction
This document forms part of a series concerned with personal protective equipment (
...