SIST EN 1469:2015

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Natursteinprodukte - Bekleidungsplatten - AnforderungenProduits en pierre naturelle - Dalles de revêtement mural - ExigencesNatural stone products - Slabs for cladding - Requirements91.100.15Mineralni materiali in izdelkiMineral materials and productsICS:Ta slovenski standard je istoveten z:EN 1469:2015SIST EN 1469:2015en,fr,de01-maj-2015SIST EN 1469:2015SLOVENSKI
STANDARDSIST EN 1469:20051DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1469
March 2015 ICS 91.100.15 Supersedes EN 1469:2004English Version
Natural stone products - Slabs for cladding - Requirements
Produits en pierre naturelle - Dalles de revêtement mural - Exigences
Natursteinprodukte - Bekleidungsplatten - Anforderungen This European Standard was approved by CEN on 3 January 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1469:2015 ESIST EN 1469:2015

Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation . 29 ZA.1 Scope and relevant characteristics . 29 ZA.2 Procedure for AVCP of natural stone slabs for cladding . 32 ZA.2.1 System(s) of AVCP . 32 ZA.2.2 Declaration of performance (DoP) . 36 ZA.2.2.1 General . 36 ZA.2.2.2 Content. 37 ZA.2.2.3 Example of DoP . 37 ZA.2.2.3.1 Example of DoP for natural stone slabs for cladding, inside use . 37 ZA.2.2.3.2 Example of DoP for natural stone slabs for cladding, outside use . 39 ZA.3 CE marking and labelling. 41 Bibliography . 45
Figure 1 — Dimensions of a slab for cladding 3.3 lower expected value lower expected value (EL) corresponds to the 5 %-quantile of a logarithmic normal distribution for a confidence level of 75 % 3.4 higher expected value higher expected value (EH) corresponds to the 95 %-quantile of a logarithmic normal distribution for a confidence level of 75 % 4 Characteristics of natural stone for cladding 4.1 Geometrical characteristics 4.1.1 General All measurements shall be carried out in accordance with EN 13373 and all measured values of individual units shall fall within the required tolerances. 4.1.2 Thickness The thickness shall be measured in accordance with EN 13373 and the measured values shall not deviate from the nominal thickness by more than given in Table 1. SIST EN 1469:2015

Up to and including 30 ±10 % More than 30
Up to and including 80 ±3 mm More than 80 ±5 mm Stricter deviations may be declared by the manufacturer. This is particularly important when the edges of the slabs will be visible after installation. NOTE If the slab is to be fixed by adhesive or a thin mortar bed, stricter tolerances may be needed. The required thickness of slabs shall result from a structural analysis or similar procedure that takes into account the technical and physical properties of the stone and the intended application. For natural cleft/riven faces, Table 1 does not apply and the deviations on thickness shall be set out by the manufacturer. 4.1.3 Flatness The deviation from flatness of the surface (except for natural cleft faces) when measured in accordance with EN 13373 shall not exceed 0,2 % of the slab length, and shall not exceed 3 mm. For natural cleft faces, the tolerance on flatness shall be declared by manufacturer. 4.1.4 Length, width and squareness The length, width or squareness shall not deviate from the nominal size by more than the tolerances given in Table 2. Measurements shall be made according to EN 13373. Table 2 — Tolerances on length, width and squareness Nominal length or width in mm < 600 ≥ 600 Sawn edges thickness ≤ 50 mm ±1 mm ±1,5 mm Sawn edges thickness > 50 mm ±2 mm ±3 mm Squareness ±1 mm ±2 mm Stricter deviations may be declared by the manufacturer. For natural cleft/riven edges, Table 2 does not apply and the tolerances on length, width and squareness shall be set out by the manufacturer. 4.1.5 Special shapes The permissible deviation at any point shall be as stated in Table 2 (see Figure 2). SIST EN 1469:2015

Key 1 nominal size 2 the slab sides shall fall within the two dotted lines indicating the tolerances of length and width according to Table 2 Figure 2 — Example of tolerances on angles 4.1.6 Location of dowel holes The specified location, depth and diameter (shape) of dowel holes shall be as follows: — Location measured along the length or width of the slab: ± 2 mm — Location measured along thickness: ± 1 mm (to be measured from the exposed face) — Depth: + 3 / - 1 mm — Diameter: + 1 / - 0,5 mm Stricter deviations may be declared by the manufacturer. For other fixing systems (e.g. slots), specific deviations shall be declared by the manufacturer. 4.1.7 Commercial sizes of slabs for cladding Commercial sizes shall be based on the area of the smallest possible circumscribed rectangle measured in square metres accurate to two decimal places. NOTE For small units it may be necessary to agree a minimum size, for example 0,25 m2. 4.1.8 Surface finish 4.1.8.1 General Surface finishes shall be carried out uniformly to the edges of the cladding slab. SIST EN 1469:2015

Key 1 reference sample 2 production sample 3 daylight Figure 3 — Comparison between production sample and reference sample SIST EN 1469:2015

1) CEN/TS 00351014 is under preparation. SIST EN 1469:2015
...