SIST EN 12767:2019

SLOVENSKI STANDARD
SIST EN 12767:2019
01-oktober-2019
Nadomešča:
SIST EN 12767:2008
Pasivna varnost nosilnih konstrukcij za opremo cest - Zahteve in preskusne
metode
Passive safety of support structures for road equipment - Requirements and test
methods
Passive Sicherheit von Tragkonstruktionen für die Straßenausstattung - Anforderungen
und Prüfverfahren
Sécurité passive des structures supports d’équipements de la route - Prescriptions et
méthodes d’essai
Ta slovenski standard je istoveten z: EN 12767:2019
ICS:
93.080.30 Cestna oprema in pomožne Road equipment and
naprave installations
SIST EN 12767:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 12767:2019

---------------------- Page: 2 ----------------------
SIST EN 12767:2019


EN 12767
EUROPEAN STANDARD

NORME EUROPÉENNE

August 2019
EUROPÄISCHE NORM
ICS 93.080.30 Supersedes EN 12767:2007
English Version

Passive safety of support structures for road equipment -
Requirements and test methods
Sécurité passive des structures supports Passive Sicherheit von Tragkonstruktionen für die
d'équipements de la route - Prescriptions et méthodes Straßenausstattung - Anforderungen und
d'essai Prüfverfahren
This European Standard was approved by CEN on 24 June 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12767:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 12767:2019
EN 12767:2019 (E)
Contents
European foreword . 4
Introduction . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 Symbols and abbreviations . 10
5 General test parameters . 11
5.1 Test site . 11
5.2 Backfill . 11
5.3 Test vehicle . 12
6 General test item parameters . 13
6.1 General test item documentation . 13
6.2 Test item selection . 13
7 Test method . 15
7.1 General . 15
7.2 Impact angle . 15
7.3 Impact point . 15
7.4 Impact speed . 21
7.5 Simplified test method for non-harmful support structures . 21
8 Impact data measurement . 22
8.1 General . 22
8.2 Impact data to be recorded. 22
8.3 Test item behaviour . 23
8.4 Vehicle behaviour . 24
8.5 Impact severity indexes . 24
8.6 Photographic coverage . 24
9 Test report . 25
9.1 General . 25
9.2 Test data decimal rounding . 25
Annex A (normative) Data evaluation . 27
Annex B (normative) Backfill requirements . 32
Annex C (informative) Push / pull test . 35
Annex D (normative) Vehicle data . 36
Annex E (normative) Vehicle calibration . 38
Annex F (informative) Bogie vehicle . 40
Annex G (normative) Product families . 41
Annex H (normative) Changed versions . 44
Annex I (normative) Determining the speed and mass of the falling support . 45
2

---------------------- Page: 4 ----------------------
SIST EN 12767:2019
EN 12767:2019 (E)
Annex J (informative) Test report . 46
Annex K (normative) Deemed to comply . 52
Annex L (normative) Use of test results performed in accordance with previous versions of
EN 12767 . 53
Annex M (normative) Virtual testing . 55
Bibliography . 69


3

---------------------- Page: 5 ----------------------
SIST EN 12767:2019
EN 12767:2019 (E)
European foreword
This document (EN 12767:2019) has been prepared by Technical Committee CEN/TC 226 “Road
Equipment”, the secretariat of which is held by AFNOR.
This document shall be given the status of a national standard, either by publication of an identical text
or by endorsement, at the latest by February 2020, and conflicting national standards shall be withdrawn
at the latest by February 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12767:2007.
The significant technical changes incorporated in this revision are:
— incorporation of the Regulation (EU) No 305/2011 of the European Parliament and of the Council of
9 March 2011 laying down harmonized conditions for the marketing of construction products and
repealing Council Directive 89/106/EEC terminology;
— introduction of a push-pull test to enable a comparison to be made between the backfills used in the
test and those on-site;
— harmonization of the boundary values for occupant safety (ASI and THIV) independent of the energy
absorption class;
— replacement of the occupant safety class by an alphanumeric character instead of a number to make
a clear distinction with the old (EN 12767:2007) approach. Now, NE-C, LE-C and HE-C have the same
occupant safety. The best occupant safety is achieved for A;
— introduction of collapse modes to classify if test items become detached or do not become detached;
— introduction of direction classes to take into account any sensitiveness to impact angle;
— improved test description, include installation manual and translation of roof deformation into a
measurable value, to reduce the influence of the vehicle structure on the test results;
— introduction of an extra test at 50 km/h for cases where the test-item is not activated at low speed.
An explanation of the definition of “activated” is also given;
— better rules for the determination of families (product families) based on the tested limit(s);
— introduction of a risk assessment approach, in line with the EN 1317-1:2010, for assessing changes
of a version, and the use of (for example) virtual testing in this;
— possibility to declare, under certain conditions, intermediate speed classes.
Most of the comments collected from all CEN members to the previous version of this norm are
implemented or solved. The definition and use of newer technologies has to be developed before
introduction into the standard.
Some added changes mentioned above are expressed in a new performance classification for the product.
This results in a longer description of the overall passive safety performance, but at the end, it gives a
clearer indication of product performance. For example, an old performance classification like “100, HE,
4

---------------------- Page: 6 ----------------------
SIST EN 12767:2019
EN 12767:2019 (E)
3” could be translated to “100-HE-C-S-SE-MD-1”. In this example, the last 4 sub-indications stands for
backfill type (S), collapse mode (SE), direction class (MD) and risk of roof indentation.
Translation of older tests to this new standard is possible when sufficient information is available in the
reports, photographs and videos of the tests.
The previous version of EN 12767 included test acceptance criteria – this is now, for convenience,
repeated in Annex A.
When this standard is used as a supporting standard for a product standard under CPR (e.g. sign
supports) relevant clauses of Annexes A, G and H are supposed to be copied inside the product standard,
and the product standard refers to the rest of this standard.
When this standard is used for testing constructions with no product standard the specifying authority is
supposed to refer to whole EN 12767, including Annexes A, G and H.
Annexes A, B, D, E, G, H, I, K, L, M of this document are normative, Annexes C, F, J are informative.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
5

---------------------- Page: 7 ----------------------
SIST EN 12767:2019
EN 12767:2019 (E)
Introduction
The severity of accidents for the occupant(s) of a vehicle is affected (in part) by the performance of the
support structures for items of road equipment under impact. Based on safety considerations, support
structures can be designed to behave in controlled ways to reduce the overall risk.
Passive safety is intended to reduce the severity of injury to vehicle occupants of a car in an impact with
support structures of road equipment.
This document has been developed in order to provide:
— test methods for determining impact safety performance; and
— methods to handle the data resulting from the impact tests;
— technical background about passive safety that can be used in the product standard.
The test procedure includes guidelines:
— for test item selection, test parameters, detailed test methods with different test conditions, the data
to record, and requirements for reporting;
— to assess the performance within families of product (called “product families”) and for modified
products (called “changed versions”).
This document considers:
— two kinds of test inputs:
— three speed classes (50, 70 and 100);
— three Backfill types (standard aggregates (S), special (X) and Rigid (R)).
— five kinds of test outcomes:
— three energy absorption classes: high energy absorbing (HE), low energy absorbing (LE) and
non-energy absorbing (NE);
— five occupant safety classes (from A to E);
— two modes of collapse for support structures (Separation mode (SE) and No separation collapse
mode (NS));
— three direction classes (single-directional (SD), bi-directional (BD) and multi-directional (MD));
— two classes of risk of roof indentation (0 or 1).
In order to help to evaluate the risk in case of a product modification, this document introduces Virtual
Testing through the definition of procedures for verification, validation, and development of numerical
models.
Based on the evaluation of the performance of each tested support structure, National and Local road
authorities will be able to specify the performance class of an item of road equipment support structure
in terms of the likely effect on the occupants of a vehicle in impact with the structure.
6

---------------------- Page: 8 ----------------------
SIST EN 12767:2019
EN 12767:2019 (E)
1 Scope
This document specifies performance test procedures to determine the passive safety properties of
support structures such as lighting columns, sign posts, signal supports, structural elements, foundations,
detachable products and any other components used to support a particular item of equipment on the
roadside.
This document provides a common basis for the vehicle impact testing of items of road equipment
support structures.
This document does not apply to road restraint systems.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1317-1:2010, Road restraint systems — Part 1: Terminology and general criteria for test methods
EN 13285, Unbound mixtures — Specifications
ISO 6487, Road vehicles — Measurement techniques in impact tests — Instrumentation
ISO 10392, Road vehicles — Determination of centre of gravity
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
3.1
impact test
test in which a test vehicle impacts a test item of road equipment support structure
3.2
impact angle
angle between the intended direction of traffic and the approach path of the test vehicle into the test item
3.3
vehicle impact point
initial point of impact on the test vehicle
3.4
test item impact point
initial point of impact on the test item
7

---------------------- Page: 9 ----------------------
SIST EN 12767:2019
EN 12767:2019 (E)
3.5
impact speed
ν
i
measured impact speed of the impacting vehicle, measured along the test vehicle approach path at a
distance no further than 6 m before the impact point
3.6
exit speed
ν
e
speed of the test vehicle after the impact with the test item, measured perpendicular to the extended
approach path at a point 12 m beyond the impact point
Note 1 to entry: For exit speed of non-harmful products as defined in 3.16, non-harmful support structure see
7.5, simplified test method for non-harmful support structures.
3.7
test vehicle
production models representative of current traffic in Europe used in an impact test to evaluate the
performance of a test item
3.8
test item
complete system of a support structure including the road equipment to be supported and foundation (if
needed)
3.9
support structure
system used to support items of road equipment
Note 1 to entry: Items of road equipment may include luminaires, traffic signs, traffic signals and utility cables or
any other equipment. The system includes posts, poles, structural elements, foundations, detachable mechanisms,
if used, and any other components used to support the particular item of equipment.
3.10
sign support
support structure intended to hold one or more signs
3.11
signal support
support structure intended to hold one or more signals heads
3.12
lighting column
support structure intended to hold one or more luminaires, consisting of one or more parts: a post,
possibly an extension piece and, if necessary, a bracket
3.13
utility pole
support structure intended to hold power transmission, telecommunication cables or similar
3.14
cantilever support
support structure with one or more legs positioned on one side of the carriageway and a cantilever arm
supporting signs, signals or other equipment mounted over traffic lanes
8

---------------------- Page: 10 ----------------------
SIST EN 12767:2019
EN 12767:2019 (E)
3.15
gantry support
support structure spanning a carriageway with one or more legs on each side of carriageway supporting
signs, signals or other equipment
3.16
multi-legged support
support structures with several legs, either identical or different
Note 1 to entry: The term includes structures with legs aligned transverse to the road or along the road.
3.17
non-harmful support structure
small support structure (for example some types of bollards, self-righting signs, delineators) that causes
only minor damage and a small change of speed during impact
3.18
ASI
dimensionless impact severity index calculated from the tri-axial vehicle accelerations according to the
procedure given by EN 1317-1:2010, 8.1.2
3.19
THIV
velocity, expressed in km/h, at which a hypothetical “point mass” occupant impacts the surface of a
hypothetical occupant compartment and calculated in accordance with the procedure given by
EN 1317-1:2010, 8.1.3
3.20
ballast
mass added to a test vehicle, excluding instrumentation, to simulate cargo and/or to achieve desired test
mass
3.21
total mass
mass that includes all items in the test vehicle at the beginning of the test
3.22
collapse mode
mode by which the support structure deforms under vehicle impact
3.23
anthropomorphic test device
ATD
anthropomorphic device representative of a 50th percentile adult, specifically designed to represent in
form, size and mass, a vehicle occupant, and to reproduce the dynamic behaviour of an occupant in crash
testing
3.24
performance class
class for one speed class, one energy absorption level, one occupant safety class, one backfill type, one
collapse mode, one direction class and risk of roof indentation
9

---------------------- Page: 11 ----------------------
SIST EN 12767:2019
EN 12767:2019 (E)
3.25
product family
product series of the same type in various sizes, made from the same materials using the same design and
general construction method, and having the same performance class
3.26
object length
height of the support structure
Note 1 to entry: For lighting columns, the object length is the height above ground level (h) plus half of the
horizontal bracket projection (w) in case of a bracket in top of the support structure. h and w are defined by EN 40-2.
Note 2 to entry: For other support structures, the object length is the overall height of the structure including
signs, signal heads and other attachments.
3.27
object mass
mass of the part of the support structure above ground level included attachments such as signs and
luminaires
4 Symbols and abbreviations
ASI Acceleration Severity Index
THIV Theoretical Head Impact Velocity
SE Separation collapse mode
NS No separation collapse mode
HE High energy absorbing category
LE Low energy absorbing category
NE Non energy absorbing category
S Backfill type S, standard aggregates
X Backfill type X, special aggregates
R Backfill type R, rigid
SD Single-directional
BD Bi-directional
MD Multi-directional
C Circumscribed circle of supports
O Centre of C
L Clear opening for multi-legged supports
ν Velocity
t Time
VT Virtual testing
NR No requirement
ATD Anthropomorphic Test Device
10

---------------------- Page: 12 ----------------------
SIST EN 12767:2019
EN 12767:2019 (E)
5 General test parameters
5.1 Test site
The test site shall be generally flat and have a level, hardened surface with a gradient not exceeding 2,5 %.
The area around the test item until 15 m behind shall be clear of standing water, ice or snow at the time
of the test. The test site shall be of sufficient size to enable the test vehicle to be accelerated up to the
required speed and controlled so that its approach to the test object is stable.
The test vehicle shall run on a levelled (no steps allowed) hardened or paved surface over the backfill
volume without influencing the movement of the test item.
NOTE For the purposes of this standard, the term “paved” is used only for an installation with asphalt, brick
slabs/pavers or a concrete surface.
Appropriate measures shall be taken in order to minimize dust generation from the test area and the test
vehicle during the impact test so that photographic records will not be obscured.
5.2 Backfill
5.2.1 General
The manufacturer shall select the type(s) of backfill to be used in the Type Tests from those given in
Table 1.
Table 1 — Backfill type
Backfill type Name
S Standard aggregates
X Special
R Rigid

The backfill at the test site shall be well known, repeatable and described thoroughly, either in the test
report or as a reference to well-known and widely accepted geotechnical references or pavement
properties.
Within one product family, the same backfill type shall be used for all tests.
The different backfill types are described in 5.2.2 and 5.2.3.
The backfill according to which the performance of the test item is determined is part of the performance
declaration (see Annex A).
5.2.2 Backfill type S and X
Backfill type S and X identify the use of backfill material in the backfill volume.
— Backfill type S grading shall be in accordance with B.3.
— Backfill type X shall be described by a sieving curve supplied by the manufacturer and included in
the test report (grading shall be in accordance with EN 13285).
The results of the push/pull test should be reported according to Annex C.
The minimum dimensions of the backfill volume, the positioning of the item in the volume and the
compaction of the backfill material shall comply with B.1 and B.2. The backfill volume shall not be frozen
at the time of test and shall be protected from rain before the impact test.
11

---------------------- Page: 13 ----------------------
SIST EN 12767:2019
EN 12767:2019 (E)
5.2.3 Backfill type R
Backfill type R identifies the use of a flat continuous rigid surface (such as asphalt and/or concrete) of a
sufficient thickness to provide anchoring of the tested item without being displaced according to B.4.
NOTE This can be locally damaged in the impact area as a result of the impact test.
5.3 Test vehicle
5.3.1 General
The test vehicle shall be a standard passenger car and shall also meet the following specifications:
— the total mass: 900 kg ± 40 kg. Of this, the maximum allowed combined mass of ballast and
instrumentation is 120 kg;
An ATD (or a driver for simplified test method) may be used; in this case the total mass includes the
ATD (or driver).
— the dimensions of the test vehicle are determined according to Annex D;
— front and rear wheel track: 1,35 m ± 0,20 m;
— longitudinal centre of gravity location in distance from front axle (CGx) 0,90 m ± 0,09 m. No ATD shall
be in the car when the centre of gravity is determined;
The centre of gravity shall be determined in accordance with the ISO 10392.
— lateral centre of gravity location (CGy) distance from vehicle centreline ±0,07 m;
— centre of gravity height from ground (CGz) 0,49 m ± 0,05 m;
— the vehicles to be used in the tests shall be production models representative of current traffic in
Europe;
— the vehicle shall not have a sunroof;
— additional equipment on the car, which might be important for the test, shall be of a type normally
delivered by the manufacturer or otherwise approved for use on the specific car type;
— a heavy car shall not be stripped of heavy standard equipment to fit into the mass restrictions of this
standard;
— the tyres shall be inflated to the vehicle manufacturer’s recommended pressures. The condition of
the vehicle shall satisfy the requirements for the issue of a vehicle certificate of road worthiness with
respect to tyres, suspension, wheel alignment and bodywork, including windows and features that
are expected to affect the test result. No repairs or modifications including reinforcement shall be
made that would alter the general characteristics of the vehicle or invalidate such a certification. Any
repairs shall conform to the original vehicle specification as defined by the vehicle manufacturer. The
vehicle shall be clean and mud deposits, which may cause dust on impact, shall be removed prior to
testing. Marker points shall be placed on external surfaces of the test vehicle to aid analysis;
— the vehicle shall not be restrained by control of the steering or any other means during impact and
within a distance of 12 m after the impact point (e.g. engine power, braking, anti-lock brakes,
blocking or fixing);
12

---------------------- Page: 14 ----------------------
SIST EN 12767:2019
EN 12767:2019 (E)
— all fluids shall be included in the test inertial mass;
— all ballast weights shall be securely fixed to the vehicle in such a way as not to exceed the
manufacturer's specifications for distribution of weight in the horizontal and vertical planes;
— ballast weights shall not be fixed in locations, which would modify the deformation of, or intrusions
into, the vehicle.
The test vehicle shall satisfy the vehicle calibration test
...