iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 13113:2003

(Main)

Tannery machines - Roller coating machines - Safety requirements

Tannery machines - Roller coating machines - Safety requirements

This European Standard deals with the following roller coating machines (see figures 2 to 4 and normative Annex A for description)
a) single and multi-roller contra-rotating machines (see figure 2)
b) single and multi-roller synchronised machines (see figure 3)
c) single and multi roller- contra-rotating /synchronised machines, so-called combined machines (see figure 4)
The machines are not intended to be used during transportation.
This standard specifies safety requirements for design, construction and operation.
It takes account of intended use, foreseeable misuse, component and systems failure.
This standard takes account of material feeding and handling devices which, when attached to the machine,
become an integral part.
This European standard applies to the machines manufactured after its date of issue.
This standard does not establish any requirements for electromagnetic disturbances.
NOTE   Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this European Standard. The present standard does not necessarily comply with Directive 94/9/EC. Additional safety requirements in a future revision of this standard may be necessary to satisfy Directive 94/9/EC.

Gerberei-Maschinen - Walzenauftragmaschinen - Sicherheitsanforderungen

Diese Europäische Norm behandelt folgende Walzenauftragmaschinen (siehe Bilder 2 bis 4 sowie Beschreibung im normativen  Anhang A):
a)   Ein- und Mehrwalzen-Gegenlaufmaschinen (siehe Bild 2)
b)   Ein- und Mehrwalzen-Gleichlaufmaschinen (siehe Bild 3)
c)   Ein- und Mehrwalzen-Gegen-/Gleichlaufmaschinen, sogenannte kombinierte Maschinen (siehe Bild 4)
Diese Maschinen sind nicht für den Gebrauch während des Transportes bestimmt.
Diese Norm spezifiziert Sicherheitsanforderungen für Konstruktion, Bau und Betrieb.
Diese Norm befasst sich mit der bestimmungsgemäßen Verwendung, vorhersehbarem Missbrauch und möglichem Versagen der Bauteile und des Systems.
Diese Norm berücksichtigt Materialzufuhr und Bedienungsvorrichtungen, die, nach Anbringen an der Maschine, zu einem integralen Bestandteil der Maschine werden.
Diese Europäische Norm gilt für Maschinen, die nach dem Datum ihrer Veröffentlichung gebaut werden.
Diese Norm legt keine Anforderungen für elektromagnetische Verträglichkeit fest.
ANMERKUNG   Die Richtlinie 94/9/EG zu Ausstattung und Sicherheitssystemen in potentiell explosionsfähiger Atmosphäre kann für die in dieser Europäischen Norm behandelten Arten von Maschinen oder Ausrüstung Anwendung finden. Die derzeitige Norm entspricht jedoch nicht in allem der Richtlinie 94/9/EG. In eine zukünftige Überarbeitung müssen zur Erfüllung der Richtlinie 94/9/EG möglicherweise zusätzliche Sicherheitsanforderungen aufgenommen werden.

Machines de tannerie - Machines d'enduction a rouleaux - Prescriptions de sécurité

La présente norme européenne s'applique aux machines d'enduction à rouleaux suivantes (pour la description, voir les figures 2 à 4 et l'annexe normative A):a) machines contrarotatives à un ou plusieurs rouleaux (voir figure 2); b) machines synchronisées à un ou plusieurs rouleaux (voir figure 3); c) machines contrarotatives/synchronisées à un ou plusieurs rouleaux, appelées machines combinées (voir figure 4). L'utilisation des machines d'enduction à rouleaux est strictement limitée aux substances à base d'eau, sauf spécification contraire autorisant des substances à base de solvant.

Strojarski stroji – Stroji za nanos z valjem – Varnostne zahteve

General Information

Status
Withdrawn
Publication Date
30-Sep-2003
Withdrawal Date
23-Sep-2010
ICS
59.140.40 - Machines and equipment for leather and fur production
Technical Committee
I13 - Imaginarni 13
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
24-Sep-2010
Due Date
17-Oct-2010
Completion Date
24-Sep-2010
Directive
98/37/EC - Machinery
Mandate
M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
Ref Project
EN 13113:2002 - Tannery machines - Roller coating machines - Safety requirements

Relations

Consolidated By
SIST EN 13113:2003+A1:2010 - Tannery machines - Roller coating machines - Safety requirements
Effective Date
01-Nov-2010
Amended By
SIST EN 13113:2003/kFprA1:2010 - Tannery machines - Roller coating machines - Safety requirements
Effective Date
01-Mar-2010

Buy Standard

EN 13113:2003EN 13113:2003
PreviousNext
Standard
EN 13113:2003
English language
39 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-oktober-2003
Strojarski stroji – Stroji za nanos z valjem – Varnostne zahteve
Tannery machines - Roller coating machines - Safety requirements
Gerberei-Maschinen - Walzenauftragmaschinen - Sicherheitsanforderungen
Machines de tannerie - Machines d'enduction a rouleaux - Prescriptions de sécurité
Ta slovenski standard je istoveten z: EN 13113:2002
ICS:
59.140.40 Stroji in oprema za Machines and equipment for
proizvodnjo usnja in krzna leather and fur production
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 13113
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2002
ICS 59.140.40
English version
Tannery machines - Roller coating machines - Safety
requirements
Machines de tannerie - Machines d'enduction à rouleaux - Gerberei-Maschinen - Walzenauftragmaschinen -
Prescriptions de sécurité Sicherheitsanforderungen
This European Standard was approved by CEN on 27 December 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13113:2002 E
worldwide for CEN national Members.

Contents
page
Foreword.4
Introduction .5
1 Scope .5
2 Normative references .5
3 Terms and definitions.7
4 List of hazards.8
4.1 Mechanical hazards .9
4.1.1 Single roller contra-rotating machine.9
4.1.2 Single roller contra-rotating machine with spreading belts.9
4.1.3 Single roller synchronised machine .9
4.1.4 Single roller synchronised machine with spreading belts .10
4.1.5 Single roller synchronised machine with rubberised roller .10
4.1.6 Single roller contra-rotating / synchronised machine (combined machine) -– Ccontra-rotating
working configuration .10
4.1.7 Single roller contra-rotating / synchronised machine (combined machine) – Synchronised
working configuration .10
4.2 High pressure fluid ejection.11
4.3 Electrical hazard.11
4.4 Slip trip and fall hazard .11
4.5 Noise .11
4.6 Thermal hazard.12
4.7 Roller changing.12
4.8 Disassembly .12
4.9 Belt washing system .12
4.10 Sides access.12
5 Safety requirements and/or measures .13
5.1 General.13
5.2 Common requirements concerning Roller coating machines .13
5.2.1 Mechanical equipment .13
5.2.2 High pressure fluid ejection.14
5.2.3 Electrical equipment (for all machines).14
5.2.4 Slip, trip and fall hazard .14
5.2.5 Noise .14
5.2.6 Control system.15
5.2.7 Emergency stop equipment.15
5.2.8 Maintenance and cleaning .16
5.2.9 Hot surfaces .17
5.2.10 Coating roller changing.17
5.2.11 Disassembly .17
5.2.12 Belt washing system .17
5.2.13 Sides access.17
5.3 Requirements concerning hazards in the working zone .17
5.3.1 Single roller- contra-rotating machine with feeding table (see Figure 2A).17
5.3.2 Single roller- contra-rotating machine with spreading belt (see Figure 2B) .18
5.3.3 Single roller synchronised machine with feeding table (see Figure 3A) .18
5.3.4 Single roller synchronised machine with spreading belts (see Figure 3B).19
5.3.5 Single roller synchronised machine with rubberised roller (see Figure 3C).19
5.3.6 Single roller contra-rotating /synchronised machine (combined machine) - contra-rotating
working configuration (see Figure 4A) .19
5.3.7 Single roller contra-rotating /synchronised machine (combined machine) - Synchronised
working configuration (see Figure 4B).20
6 Verification of the safety requirements and/or measures .20
7 Information for use .29
7.1 Instruction Handbook.29
7.1.1 Machine.29
7.1.2 Installation of the machine .29
7.1.3 Transportation and Storage of the machine and machine parts .30
7.1.4 Use of the machine.30
7.1.5 Maintenance .30
7.2 Marking .30
Annex A (normative)  Machinery description.37
Annex ZA (informative)  Relationship of this document with EC Directives.38
Bibliography .39
Foreword
This document EN 13113:2002 has been prepared by Technical Committee CEN/TC 200 "Tannery machines and
plant - Safety", the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by October 2002, and conflicting national standards shall be withdrawn at the latest
by October 2002.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative annex ZA, which is an integral part of this document.
Annex A is normative.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,
Sweden, Switzerland and the United Kingdom.
Introduction
This European Standard is a type C standard as stated in EN 1070.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are
indicated in the scope of this standard.
1 Scope
This European Standard deals with the following roller coating machines (see Figures 2 to 4 and normative annex
A for description):
a) single and multi-roller contra-rotating machines (see Figure 2);
b) single and multi-roller synchronised machines (see Figure 3);
c) single and multi roller- contra-rotating /synchronised machines, so-called combined machines (see Figure 4).
The machines are not intended to be used during transportation.
This standard specifies safety requirements for design, construction and operation.
It takes account of intended use, foreseeable misuse, component and systems failure.
This standard takes account of material feeding and handling devices which, when attached to the machine,
become an integral part.
This European Standard applies to the machines manufactured after its date of issue.
This standard does not establish any requirements for electromagnetic disturbances.
NOTE Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive
atmospheres can be applicable to the type of machine or equipment covered by this European Standard. The present standard
does not necessarily comply with Directive 94/9/EC. Additional safety requirements in a future revision of this standard can be
necessary to satisfy Directive 94/9/EC.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of the
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 972:2000+A1:2011/AC:2011(Corrigendum)
Tannery machines - Reciprocating roller machines - Safety requirements
EN 972:1998+A1:2010/AC:2011

This European Standard specifies safety requirements for all the phases of the life of a machine listed in 5.3 a) of EN ISO 12100-1:2003. Reciprocating roller machines are machines used for the processing of animal hides and skins. They have a reciprocating opening and closing motion of the feed rollers or conveyors which, if required, may also reverse their direction. This standard covers the following reciprocating roller machines a) Buffing machines b) Polishing machines c) Ironing machines (woolskins and fur) d) Carding machines e) Shearing machines (woolskins and fur) f) Cylinder universal staking machines g) Setting-out machines h) Dewooling machines i) Scudding machines j) Unhairing (dehairing) machines k) Sammying machines l) Cylinder ironing machines m) Cylinder staking machines n) Fleshing machines o) Demanuring machines p) Wet wheeling machines q) Shaving machines (feed-out) r) Shaving machines (feed-in) It takes account of intended use, foreseeable misuse, component and systems failure. This European Standard is not applicable to reciprocating roller machines which are manufactured before the date of its publication as EN. This European Standard provides provisions for the reduction of noise emission at the design stage. However, it does not provide a noise test code for the determination by measurement of noise emission values for the machines it covers. Without such a code the manufacturer cannot fulfil his obligation to provide the noise emission values of the machines put on the market. All the significant hazards are dealt with in this European Standard except the following: - Dust, smoke and vapour emissions; - Fire. For these hazards general guidelines are proposed in normative annexes. Designers and manufacturers shall verify directly that the methods adopted to reduce these hazards have been successful.

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 972:2000+A1:2011(Main)
Tannery machines - Reciprocating roller machines - Safety requirements
EN 972:1998+A1:2010

This European Standard specifies safety requirements for all the phases of the life of a machine listed in
5.3 a) of EN ISO 12100-1:2003.
Reciprocating roller machines are machines used for the processing of animal hides and skins. They have a reciprocating opening and closing motion of the feed rollers or conveyors which, if required, may also reverse their direction.
This standard covers the following reciprocating roller machines (see figures 1 to 13 for typical configurations and annex D for descriptions):
a)   Buffing machines (see figures 1a and 1b)
b)   Polishing machines (see figures 1a and 1b)
c)   Ironing machines (woolskins and fur) (see figures 2a and 2b)
d)   Carding machines (see figures 3a and 3b)
e)   Shearing machines (woolskins and fur) (see figures 4a and 4b)
f)   Cylinder universal staking machines (see figures 5a and 5b)
g)   Setting-out machines (see figures 6a and 6b)
h)   Dewooling machines (see figures 6a and 6b)
i)   Scudding machines (see figures 6a and 6b)
j)   Unhairing (dehairing) machines (see figures 6a and 6b)
k)   Sammying machines (see figures 6a and 6b)
l)   Cylinder ironing machines (see figures 7a and 7b)
m)   Cylinder staking machines (see figures 8a and 8b)
n)   Fleshing machines (see figures 9a and 9b)
o)   Demanuring machines (see figures 10a and 10b)
p)   Wet wheeling machines (see figures 11a and 11b)
q)   Shaving machines (feed-out) (see figures 12a and 12b)
r)   Shaving machines (feed-in) (see figures 13a and 13b)
It takes account of intended use, foreseeable misuse, component and systems failure.
This European Standard is not applicable to reciprocating roller machines which are manufactured before the date of its publication as EN.
This European Standard provides provisions for the reduction of noise emission at the design stage (see 5.2.4 and Annex A). However, it does not provide a noise test code for the determination by measurement of noise emission values for the machines it covers. Without such a code the manufacturer c

  • Standard
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13113:2003+A1:2010(Main)
Tannery machines - Roller coating machines - Safety requirements
EN 13113:2002+A1:2010

This European Standard deals with the following roller coating machines (see Figures 2 to 4 and normative annex A for description):
a)   single and multi-roller contra-rotating machines (see Figure 2);
b)   single and multi-roller synchronised machines (see Figure 3);
c)   single and multi roller- contra-rotating /synchronised machines, so-called combined machines (see Figure 4).
The machines are not intended to be used during transportation.
This standard specifies safety requirements for design, construction and operation.
It takes account of intended use, foreseeable misuse, component and systems failure.
This standard takes account of material feeding and handling devices which, when attached to the machine, become an integral part.
This document is not applicable to the roller coating machines which are manufactured before the date of its publication as EN.
This standard does not establish any requirements for electromagnetic disturbances.
NOTE   Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this European Standard. The present standard does not necessarily comply with Directive 94/9/EC. Additional safety requirements in a future revision of this standard can be necessary to satisfy Directive 94/9/EC.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13457:2005+A1:2010(Main)
Footwear, leather and imitation leather goods manufacturing machines - Splitting, skiving, cutting, cementing and cement drying machines - Safety requirements
EN 13457:2004+A1:2010

This document applies to splitting, skiving, edge trimming, strip cutting, cementing and cement drying machines used in the manufacture of footwear, leather and imitation leather goods and other related components.
1.2   This document does not apply to:
-   trimming machines with rotary milling tool for the purpose of trimming edges of material, see EN 930;
-   splitting and band knife machines used in tanneries, see EN 13112;
-   portable machines.
1.3   This document specifies safety requirements for construction, transport, installation, adjustment, setting, teaching or process change-over, operation, cleaning, maintenance, decommissioning, dismantling and, as far as safety is concerned, disposal for machines mentioned in 1.1.
It takes account of intended use , foreseeable misuse, component and system failure.
1.4   This document deals with significant hazards relevant to the footwear, leather and imitation leather goods manufacturing industries. (For a list of hazards see Clause 4.)
The document does not deal with precise technical measures for reducing the risks of fumes and dusts detrimental to health.
The use of machines falling within the scope of this document for purposes other than those specified in 1.1, may give rise to hazards not considered during its preparation.
1.5   This document also applies to equipment for material handling and operations which are an integral part of the machine.
1.6   This document assumes the machines
-   are operated by adequately trained persons
-   are used with adequate workplace lighting conforming the local regulations or to EN 12464-1
1.7   This document is not applicable to splitting, skiving, edge trimming, strip cutting, cementing and cement drying machines which are manufactured before the date of its publication as EN.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13114:2003+A1:2010(Main)
Tannery machines - Rotating process vessels - Safety requirements
EN 13114:2002+A1:2009

1.1   This European Standard specifies safety requirements for design, construction, operation, adjustment, setting, cleaning and maintenance of a machine.
1.2   This standard covers the following machines (see annex C and Figures 1 and 2 for typical configurations):
a)   horizontal rotating vessels;
b)   inclined rotating vessels.
1.3   This standard does not apply to machines using substances containing solvent, that would generate fume and/or vapour detrimental to health, or that may lead to fire or explosive atmosphere.
1.4   This standard takes account of intended use, foreseeable misuse, component and systems failure.
The machines are for fixed installation.
1.5   This document is not applicable to the rotating vessels which are manufactured before the date of its publication as EN.
1.6   This standard does not establish any requirements for electromagnetic disturbances.
NOTE    Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this European Standard. The present standard does not necessarily comply with Directive 94/9/EC. Additional safety requirements in a future revision of this standard can be necessary to satisfy Directive 94/9/EC.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13112:2003+A1:2010(Main)
Tannery machines - Splitting and bandknife shearing machines - Safety requirements
EN 13112:2002+A1:2009

This European Standard specifies safety requirements for design, construction, operation, adjustment, setting, cleaning and maintenance of
-   splitting machines (see figures 1, 2) for limed hides and skins, wet blue and dry materials,
-   bandknife shearing machines (see figures 3, 4, 5, 6)
used in the splitting and shearing of leather and synthetic materials.
This standard takes account of intended use, foreseeable misuse, component and systems failure.
The machines are for fixed installation.
This document is not applicable to the splitting and bandknife shearing machines which are manufactured before the date of its publication as EN.
All the significant hazards listed in clause 4 are safeguarded by the requirements included in clause 5 except dust and fire.
For these hazards general guidelines are proposed in normative annex A.
Designers and manufacturers shall verify directly that the methods adopted to reduce these hazards have been successful.
This standard does not establish any requirements for electromagnetic disturbances.
NOTE   Directive 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this European Standard. The present standard does not necessarily comply with Directive 94/9/EC. Additional safety requirements in a future revision of this standard can be necessary to satisfy Directive 94/9/EC.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12044:2005+A1:2009(Main)
Footwear, leather and imitation leather goods manufacturing machines - Cutting and punching machines - Safety requirements
EN 12044:2005+A1:2009

1.1   This European Standard specifies safety requirements for the design and operation of the machines defined in 1.2.
It takes account of intended use, foreseeable misuse and component and system failure.
1.2   This European Standard applies for cutting and punching machines used in the manufacture of footwear, leather and imitation leather goods and other related components. This European Standard applies to the following cutting and punching machines:
-   swing arm cutting presses with manual or powered swing arm;
-   manual and automatic travelling head cutting presses with powered travelling head;
-   manual and automatic beam cutting presses;
-   punching and perforating presses;
-   C-frame cutting presses.
1.3   This European Standard is not applicable to:
-   mechanical presses;
-   presses intended for working cold metal;
-   fastening, riveting, stitching, stapling, bending or folding machines;
-   guillotines, shears and similar machines;
-   shoe and leather presses as described in EN 12203.
1.4   This European Standard deals with all significant hazards, hazardous situations and events relevant to the footwear, leather and imitation leather goods manufacturing machinery defined in 1.2, when it is used as intended and under the conditions foreseen by the manufacturer (see Clause 4) and is intended for operation in applications by trained persons.
1.5   This European Standard deals with material feeding and handling devices, when attached to the machine.
1.6   This European Standard is not applicable to machines which are manufactured before the date of publication of this European Standard by CEN.

  • Standard
    68 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 930:2000+A2:2009(Main)
Footwear, leather and imitation leather goods manufacturing machines - Roughing, scouring, polishing and trimming machines - Safety requirements
EN 930:1997+A2:2009

1.1   This standard applies to the following machines which are intended to work material for the manufacture of footwear:
-   Automatic and manual roughing, scouring and polishing machines;
-   Automatic and manual edge contour trimming machines.
1.2   This standard does not apply to modular shoe repair machines.
1.3   This standard specifies safety requirements for design, construction and operation.
It takes account of intended use, foreseeable misuse, component and system failure.
1.4   This standard covers all hazards relevant to the footwear, leather and imitation leather goods manufacturing industries.
The use of machines within the scope of this standard in different industries may give rise to hazards which were not taken into account at the time of its preparation.
1.5   This document is not applicable to roughing, scouring, polishing and trimming machines which are manufactured before the date of its publication as EN.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12653:2000+A2:2009(Main)
Footwear, leather and imitation leather manufacturing machines - Nailing machines - Safety requirements
EN 12653:1999+A2:2009

This standard is applicable to nailing machines used in the footwear manufacturing industry, namely:
-   heel attaching machines (see figure 1)
-   heel nailing machines (see figure 2)
-   gang nailing machines (see figure 3)
This standard does not apply to gang nailing machines which comply in all respects with the requirements for seat lasting machines: see EN 931.
This standard specifies safety requirements for the design and construction of nailing machines. No specific requirements are included for transport, commissioning and decommissioning.
It takes account of intended use, !foreseeable misuse and component" and system failure.
This standard covers all hazards relevant to the footwear manufacturing industry. Use of the machines within the scope of this standard in different industries may give rise to hazards which were not taken into account at the time of its preparation.
This document is not applicable to nailing machines which are manufactured before the date of its publication as EN.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12203:2004+A1:2009(Main)
Footwear, leather and imitation leather goods manufacturing machines - Shoe and leather presses - Safety requirements
EN 12203:2003+A1:2009

This European Standard is applicable to shoe and leather presses (see 3.1) used in the manufacture of footwear, leather and imitation leather goods and other related components. These machines are:
-   Sole attaching presses (open and closed types);
-   Sole and insole moulding machines;
-   Back part moulding machines;
-   Backer, lining and toe puff attaching presses;
-   Ironing presses;
-   Marking, stamping, labelling and embossing machines;
-   Stitch marking machines;
-   Upper preforming machines;
-   Automatic shoe and leather presses;
a)   Premoulding machines for thermoplastic counters and counter forming machines;
b)   Integrated manufacturing systems;
c)   Presses with mobile stations and rotary configuration;
-   Folding presses;
-   Activating presses;
-   Relasting and last slipping machines;
-   Top piece attaching presses;
-   Leather button covering machines.
1.2   This European Standard is not applicable to:
-   Cutting and punching machines;
NOTE   !See EN 12044."
-   Eyelet, hook and decorative nail attaching machines;
"deleted text"
-   Presses used for shoe repair and orthopaedic works
NOTE   "See EN 12387."
1.3   This European Standard specifies safety requirements for construction, transport, installation, adjustment, setting, teaching or process change-over, operation, cleaning, maintenance, decommissioning, dismantling and, as far as safety is concerned, disposal for machines mentioned in 1.1.
It takes account of intended use, foreseeable misuse, component and system failure.
1.4   This European Standard covers significant hazards relevant to the footwear, leather and imitation leather goods manufacturing industries. (List of hazards see 4.)
This European Standard does not deal with precise technical measures for reducing the risks of fumes and dusts detrimental to health.
The use of machines within the scope of this European Standard in industries other than those specified in 1.1 can give rise to hazard not considered during its preparation.

  • Standard
    86 pages
    English language
    sale 10% off
    e-Library read for
    1 day