SIST EN ISO 3630-3:2015

SLOVENSKI STANDARD
SIST EN ISO 3630-3:2015
01-december-2015
1DGRPHãþD
SIST EN ISO 3630-3:2000
Zobozdravstvo - Instrumenti za zobni kanal - 3. del: Kompaktorji (ISO 3630-3:2015)
Dentistry - Endodontic instruments - Part 3: Compactors: pluggers and spreaders (ISO
3630-3:2015)
Zahnheilkunde - Endodontische Instrumente - Teil 3: Verdichter: Stopfer und Spreizer
(ISO 3630-3:2015)
Médecine bucco-dentaire - Instruments d'endodontie - Partie 3: Compacteurs axiaux et
latéraux (ISO 3630-3:2015)
Ta slovenski standard je istoveten z: EN ISO 3630-3:2015
ICS:
11.060.25 =RERWHKQLþQLLQVWUXPHQWL Dental instruments
SIST EN ISO 3630-3:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 3630-3:2015

---------------------- Page: 2 ----------------------

SIST EN ISO 3630-3:2015


EN ISO 3630-3
EUROPEAN STANDARD

NORME EUROPÉENNE

September 2015
EUROPÄISCHE NORM
ICS 11.060.20 Supersedes EN ISO 3630-3:1996
English Version

Dentistry - Endodontic instruments - Part 3: Compactors:
pluggers and spreaders (ISO 3630-3:2015)
Médecine bucco-dentaire - Instruments d'endodontie - Zahnheilkunde - Endodontische Instrumente - Teil 3:
Partie 3: Compacteurs axiaux et latéraux (ISO 3630- Verdichter: Stopfer und Spreizer (ISO 3630-3:2015)
3:2015)
This European Standard was approved by CEN on 16 August 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3630-3:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 3630-3:2015
EN ISO 3630-3:2015 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 3630-3:2015
EN ISO 3630-3:2015 (E)
European foreword
This document (EN ISO 3630-3:2015) has been prepared by Technical Committee ISO/TC 106
"Dentistry" in collaboration with Technical Committee CEN/TC 55 “Dentistry” the secretariat of which
is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2016, and conflicting national standards shall
be withdrawn at the latest by March 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 3630-3:1996.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 3630-3:2015 has been approved by CEN as EN ISO 3630-3:2015 without any
modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 3630-3:2015

---------------------- Page: 6 ----------------------

SIST EN ISO 3630-3:2015
INTERNATIONAL ISO
STANDARD 3630-3
Second edition
2015-09-01
Dentistry — Endodontic
instruments —
Part 3:
Compactors: pluggers and spreaders
Médecine bucco-dentaire — Instruments d’endodontie —
Partie 3: Compacteurs axiaux et latéraux
Reference number
ISO 3630-3:2015(E)
©
ISO 2015

---------------------- Page: 7 ----------------------

SIST EN ISO 3630-3:2015
ISO 3630-3:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 3630-3:2015
ISO 3630-3:2015(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Types . 2
5 Classification . 2
6 Requirements . 2
6.1 Material . 2
6.2 Dimensional requirements . 2
6.2.1 General. 2
6.2.2 Diameters . 2
6.2.3 Length. 2
6.2.4 Hand compactors . 5
6.3 Mechanical requirements . 6
6.3.1 Stiffness (resistance to bending), finger compactors . 6
6.3.2 Stiffness (resistance to bending), hand compactors . 6
6.3.3 Stiffness (resistance to bending), heat carrier instruments. 6
6.3.4 Handle security . 6
6.3.5 Surface finish . 6
6.4 Resistance to reprocessing . 6
6.5 Colour coding . 6
7 Sampling . 6
8 Testing . 7
8.1 General . 7
8.1.1 Size . 7
8.1.2 Stiffness (resistance to bending), finger instruments . 7
8.1.3 Stiffness (resistance to bending), hand instruments . 8
8.1.4 Bending (stiffness), heat carrier instruments . 9
9 Designation, marking, and identification . 9
10 Packaging . 9
11 Manufacturer’s instructions for use . 9
12 Labelling . 9
Bibliography .10
© ISO 2015 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 3630-3:2015
ISO 3630-3:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 106, Dentistry, Subcommittee SC 4, Dental
instruments.
This second edition cancels and replaces the first edition (ISO 3630-3:1994), which has been technically
revised with the following changes:
...