SIST IEC 62642-2-2:2024
(Main)Alarm systems - Intrusion and hold-up systems - Part 2-2: Intrusion detectors - Passive infrared detectors
Alarm systems - Intrusion and hold-up systems - Part 2-2: Intrusion detectors - Passive infrared detectors
IEC 62642-2-2:2010 is for passive infrared detectors installed in buildings and provides for security grades 1 to 4 (see IEC 62642-1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see IEC 62599-1). A detector shall fulfil all the requirements of the specified grade.
Systèmes d'alarme - Systèmes d'alarme contre l'intrusion et les hold-up - Partie 2-2: Détecteurs d'intrusion - Détecteurs à infrarouges passifs
La CEI 62642-2-2:2010 concerne les détecteurs à infrarouges passifs installés dans les immeubles et est prévue pour les grades de sécurité 1 à 4 (voir la CEI 62642-1), les détecteurs filaires spécifiques ou non spécifiques ou non filaires, et l'utilisation des classes d'environnement I à IV (voir la CEI 62599-1). Un détecteur doit remplir toutes les exigences du grade spécifié.
Alarmni sistemi - Sistemi za javljanje vloma in ropa - 2-2. del: Detektorji vloma - Pasivni infrardeči detektorji (IEC 62642-2-2:2010)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2024
Nadomešča:
SIST IEC 60839-2-2:1995
SIST IEC 60839-2-6:1995
Alarmni sistemi - Sistemi za javljanje vloma in ropa - 2-2. del: Detektorji vloma -
Pasivni infrardeči detektorji (IEC 62642-2-2:2010)
Alarm systems - Intrusion and hold-up systems - Part 2-2: Intrusion detectors - Passive
infrared detectors
Systèmes d'alarme - Systèmes d'alarme contre l'intrusion et les hold-up - Partie 2-2:
Détecteurs d'intrusion - Détecteurs à infrarouges passifs
Ta slovenski standard je istoveten z: IEC 62642-2-2:2010
ICS:
13.310 Varstvo pred kriminalom Protection against crime
13.320 Alarmni in opozorilni sistemi Alarm and warning systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
IEC 62642-2-2 ®
Edition 1.0 2010-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Alarm systems – Intrusion and hold-up systems –
Part 2-2: Intrusion detectors – Passive infrared detectors
Systèmes d'alarme – Systèmes d'alarme contre l’intrusion et les hold-up –
Partie 2-2: Détecteurs d'intrusion – Détecteurs à infrarouges passifs
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
X
CODE PRIX
ICS 13.320 ISBN 978-2-88912-197-7
– 2 – 62642-2-2 © IEC:2010
CONTENTS
FOREWORD.5
INTRODUCTION.7
1 Scope.8
2 Normative references .8
3 Terms, definitions and abbreviations .8
3.1 Terms and definitions .8
3.2 Abbreviations .9
4 Functional requirements .9
4.1 Event processing.9
4.2 Detection.11
4.2.1 Detection performance .11
4.2.2 Indication of detection .12
4.2.3 Significant reduction of range .12
4.3 Operational requirements .13
4.3.1 Time interval between intrusion signals or messages .13
4.3.2 Switch on delay .13
4.3.3 Self tests .13
4.4 Immunity to incorrect operation .13
4.4.1 Immunity to air flow .13
4.4.2 Immunity to visible and near infrared radiation.13
4.5 Tamper security .13
4.5.1 Resistance to and detection of unauthorised access to components
and means of adjustment.14
4.5.2 Detection of removal from the mounting surface .14
4.5.3 Resistance to, or detection of, re-orientation .14
4.5.4 Immunity to magnetic field interference .14
4.5.5 Detection of masking .14
4.6 Electrical requirements.15
4.6.1 Detector current consumption .15
4.6.2 Slow input voltage change and voltage range limits .15
4.6.3 Input voltage ripple.15
4.6.4 Input voltage step change.15
4.7 Environmental classification and conditions.16
4.7.1 Environmental classification .16
4.7.2 Immunity to environmental conditions .16
5 Marking, identification and documentation .16
5.1 Marking and/or identification.16
5.2 Documentation .16
6 Testing .17
6.1 General test conditions.17
6.1.1 Standard conditions for testing .17
6.1.2 General detection testing environment and procedures.17
6.1.3 Testing environment .17
6.1.4 Standard walk test target.17
6.1.5 Testing procedures.18
6.2 Basic detection test .18
62642-2-2 © IEC:2010 – 3 –
6.2.1 Basic detection target (BDT).18
6.2.2 Basic test of detection capability.18
6.3 Walk testing .19
6.3.1 General walk test method .19
6.3.2 Verification of detection performance.19
6.3.3 Detection across and within the detection boundary .19
6.3.4 Verify the high-velocity detection performance.20
6.3.5 Verify the intermittent movement detection performance.20
6.3.6 Verify the close-in detection performance .21
6.3.7 Verify the significant reduction of specified range .21
6.4 Switch-on delay, time interval between signals and indication of detection .21
6.5 Self tests.21
6.6 Immunity to incorrect operation .22
6.6.1 Immunity to air flow .22
6.6.2 Immunity to visible and near infrared radiation.22
6.7 Tamper security .22
6.7.1 Resistance to and detection of unauthorised access to the inside of
the detector through covers and existing holes .23
6.7.2 Detection of removal from the mounting surface .23
6.7.3 Resistance to or detection of re-orientation of adjustable mountings.23
6.7.4 Resistance to magnetic field interference .23
6.7.5 Detection of detector masking .23
6.7.6 Immunity to false masking signals .24
6.8 Electrical tests.25
6.8.1 Detector current consumption .25
6.8.2 Slow input voltage change and input voltage range limits .25
6.8.3 Input voltage ripple.25
6.8.4 Input voltage step change.26
6.8.5 Total loss of power supply .26
6.9 Environmental classification and conditions.26
6.10 Marking, identification and documentation .28
6.10.1 Marking and/or identification.28
6.10.2 Documentation .28
Annex A (normative) Dimensions and requirements of the standardised test magnets .29
Annex B (normative) General testing matrix .32
Annex C (informative) Walk test diagrams .34
Annex D (normative) Procedure for calculation of average temperature difference.37
Annex E (informative) Basic detection target for the basic test of detection capability .39
Annex F (informative) Equipment for walk test velocity control .40
Annex G (informative) Immunity to visible and near infrared radiation – Notes on
calibration of the light source .41
Annex H (informative) Example list of small tools.42
Annex I (informative) Test for resistance to re-orientation of adjustable mountings .43
Bibliography.45
Figure A.1 – Test magnet – Magnet type 1.30
Figure A.2 – Test magnet – Magnet type 2.31
Figure C.1 – Detection across the boundary .34
– 4 – 62642-2-2 © IEC:2010
Figure C.2 – Detection within the boundary.34
Figure C.3 – High velocity and intermittent movement.35
Figure C.4 – Close-in detection.35
Figure C.5 – Significant range reduction .36
Figure I.1 – Re-orientation test .44
Table 1 – Events to be processed by grade .10
Table 2 – Generation of signals or messages .11
Table 3 – General walk test velocity and attitude requirements .12
Table 4 – Tamper security requirements .15
Table 5 – Electrical requirements.15
Table 6 – Range of materials for masking tests.24
Table 7 – Operational tests.27
Table 8 – Endurance tests .27
62642-2-2 © IEC:2010 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ALARM SYSTEMS –
INTRUSION AND HOLD-UP SYSTEMS –
Part 2-2: Intrusion detectors –
Passive infrared detectors
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations li
...
IEC 62642-2-2 ®
Edition 1.0 2010-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Alarm systems – Intrusion and hold-up systems –
Part 2-2: Intrusion detectors – Passive infrared detectors
Systèmes d'alarme – Systèmes d'alarme contre l’intrusion et les hold-up –
Partie 2-2: Détecteurs d'intrusion – Détecteurs à infrarouges passifs
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 62642-2-2 ®
Edition 1.0 2010-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Alarm systems – Intrusion and hold-up systems –
Part 2-2: Intrusion detectors – Passive infrared detectors
Systèmes d'alarme – Systèmes d'alarme contre l’intrusion et les hold-up –
Partie 2-2: Détecteurs d'intrusion – Détecteurs à infrarouges passifs
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
X
CODE PRIX
ICS 13.320 ISBN 978-2-88912-197-7
– 2 – 62642-2-2 © IEC:2010
CONTENTS
FOREWORD.5
INTRODUCTION.7
1 Scope.8
2 Normative references .8
3 Terms, definitions and abbreviations .8
3.1 Terms and definitions .8
3.2 Abbreviations .9
4 Functional requirements .9
4.1 Event processing.9
4.2 Detection.11
4.2.1 Detection performance .11
4.2.2 Indication of detection .12
4.2.3 Significant reduction of range .12
4.3 Operational requirements .13
4.3.1 Time interval between intrusion signals or messages .13
4.3.2 Switch on delay .13
4.3.3 Self tests .13
4.4 Immunity to incorrect operation .13
4.4.1 Immunity to air flow .13
4.4.2 Immunity to visible and near infrared radiation.13
4.5 Tamper security .13
4.5.1 Resistance to and detection of unauthorised access to components
and means of adjustment.14
4.5.2 Detection of removal from the mounting surface .14
4.5.3 Resistance to, or detection of, re-orientation .14
4.5.4 Immunity to magnetic field interference .14
4.5.5 Detection of masking .14
4.6 Electrical requirements.15
4.6.1 Detector current consumption .15
4.6.2 Slow input voltage change and voltage range limits .15
4.6.3 Input voltage ripple.15
4.6.4 Input voltage step change.15
4.7 Environmental classification and conditions.16
4.7.1 Environmental classification .16
4.7.2 Immunity to environmental conditions .16
5 Marking, identification and documentation .16
5.1 Marking and/or identification.16
5.2 Documentation .16
6 Testing .17
6.1 General test conditions.17
6.1.1 Standard conditions for testing .17
6.1.2 General detection testing environment and procedures.17
6.1.3 Testing environment .17
6.1.4 Standard walk test target.17
6.1.5 Testing procedures.18
6.2 Basic detection test .18
62642-2-2 © IEC:2010 – 3 –
6.2.1 Basic detection target (BDT).18
6.2.2 Basic test of detection capability.18
6.3 Walk testing .19
6.3.1 General walk test method .19
6.3.2 Verification of detection performance.19
6.3.3 Detection across and within the detection boundary .19
6.3.4 Verify the high-velocity detection performance.20
6.3.5 Verify the intermittent movement detection performance.20
6.3.6 Verify the close-in detection performance .21
6.3.7 Verify the significant reduction of specified range .21
6.4 Switch-on delay, time interval between signals and indication of detection .21
6.5 Self tests.21
6.6 Immunity to incorrect operation .22
6.6.1 Immunity to air flow .22
6.6.2 Immunity to visible and near infrared radiation.22
6.7 Tamper security .22
6.7.1 Resistance to and detection of unauthorised access to the inside of
the detector through covers and existing holes .23
6.7.2 Detection of removal from the mounting surface .23
6.7.3 Resistance to or detection of re-orientation of adjustable mountings.23
6.7.4 Resistance to magnetic field interference .23
6.7.5 Detection of detector masking .23
6.7.6 Immunity to false masking signals .24
6.8 Electrical tests.25
6.8.1 Detector current consumption .25
6.8.2 Slow input voltage change and input voltage range limits .25
6.8.3 Input voltage ripple.25
6.8.4 Input voltage step change.26
6.8.5 Total loss of power supply .26
6.9 Environmental classification and conditions.26
6.10 Marking, identification and documentation .28
6.10.1 Marking and/or identification.28
6.10.2 Documentation .28
Annex A (normative) Dimensions and requirements of the standardised test magnets .29
Annex B (normative) General testing matrix .32
Annex C (informative) Walk test diagrams .34
Annex D (normative) Procedure for calculation of average temperature difference.37
Annex E (informative) Basic detection target for the b
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.