SIST EN 1440:2016+A1:2018/kFprA2:2019
(Amendment)LPG equipment and accessories - Transportable refillable traditional welded and brazed steel Liquefied Petroleum Gas (LPG) cylinders - Periodic inspection
LPG equipment and accessories - Transportable refillable traditional welded and brazed steel Liquefied Petroleum Gas (LPG) cylinders - Periodic inspection
This European Standard specifies procedures for the periodic inspection and testing, of transportable refillable LPG cylinders with a water capacity from 0,5 l up to and including 150 l.
This European Standard is applicable to welded and brazed steel LPG cylinders with a specified minimum wall thickness designed according to EN 1442, EN 12807, EN 13322-1, or equivalent standard (e.g. national codes).
This European Standard is intended to be applied to cylinders complying with RID/ADR (including pi marked cylinders) and also to existing non RID/ADR cylinder populations.
NOTE The requirements of RID/ADR take precedence over those of this standard in the case of cylinders complying with that regulation, including pi marked cylinders.
This European Standard does not apply to cylinders permanently installed in vehicles.
Flüssiggas-Geräte und Ausrüstungsteile - Ortsbewegliche, wiederbefüllbare, geschweißte und hartgelötete Flaschen aus Stahl für Flüssiggas (LPG) - Wiederkehrende Inspektion
Equipements pour GPL et leurs accessoires - Bouteilles de gaz de pétrole liquéfié (GPL) en acier soudé et brasé transportables et rechargeables - Contrôle périodique
Oprema in pribor za utekočinjeni naftni plin (UNP) - Premične, ponovno polnljive, varjene in trdo spajkane jeklenke iz jekla za UNP - Periodična kontrola - Dopolnilo A2
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 1440:2016+A1:2018/oprA2:2019
01-april-2019
2SUHPDLQSULERU]DXWHNRþLQMHQLQDIWQLSOLQ 813 3UHPLþQHSRQRYQRSROQOMLYH
YDUMHQHLQWUGRVSDMNDQHMHNOHQNHL]MHNOD]D8133HULRGLþQDNRQWUROD'RSROQLOR
$
LPG equipment and accessories - Transportable refillable traditional welded and brazed
steel Liquefied Petroleum Gas (LPG) cylinders - Periodic inspection
Flüssiggas-Geräte und Ausrüstungsteile - Ortsbewegliche, wiederbefüllbare,
geschweißte und hartgelötete Flaschen aus Stahl für Flüssiggas (LPG) -
Wiederkehrende Inspektion
Equipements pour GPL et leurs accessoires - Bouteilles de gaz de pétrole liquéfié (GPL)
en acier soudé et brasé transportables et rechargeables - Contrôle périodique
Ta slovenski standard je istoveten z: EN 1440:2016+A1:2018/prA2:2019
ICS:
23.020.35 Plinske jeklenke Gas cylinders
SIST EN 1440:2016+A1:2018/oprA2:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1440:2016+A1:2018/oprA2:2019
---------------------- Page: 2 ----------------------
SIST EN 1440:2016+A1:2018/oprA2:2019
DRAFT
EUROPEAN STANDARD
EN 1440:2016+A1:2018
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
March 2019
ICS 23.020.35
English Version
LPG equipment and accessories - Transportable refillable
traditional welded and brazed steel Liquefied Petroleum
Gas (LPG) cylinders - Periodic inspection
Equipements pour GPL et leurs accessoires - Bouteilles Flüssiggas-Geräte und Ausrüstungsteile -
de gaz de pétrole liquéfié (GPL) en acier soudé et brasé Ortsbewegliche, wiederbefüllbare, geschweißte und
transportables et rechargeables - Contrôle périodique hartgelötete Flaschen aus Stahl für Flüssiggas (LPG) -
Wiederkehrende Inspektion
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 286.
This draft amendment A2, if approved, will modify the European Standard EN 1440:2016+A1:2018. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Irel
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.