SIST EN 12588:2007

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Lead and lead alloys - Rolled lead sheet for building purposesQLãWYRPlomb et alliages de plomb - Feuilles de plomb laminé pour le bâtimentBlei und Bleilegierungen - Gewalzte Bleche aus Blei für das BauwesenTa slovenski standard je istoveten z:EN 12588:2006SIST EN 12588:2007en77.150.60L]GHONLLead, zinc and tin productsICS:SIST EN 12588:20001DGRPHãþDSLOVENSKI
STANDARDSIST EN 12588:200701-februar-2007

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12588December 2006ICS 77.150.60Supersedes EN 12588:1999
English VersionLead and lead alloys - Rolled lead sheet for building purposesPlomb et alliages de plomb - Feuilles de plomb laminé pourle bâtimentBlei und Bleilegierungen - Gewalzte Bleche aus Blei für dasBauwesenThis European Standard was approved by CEN on 19 November 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12588:2006: E

European numbering system for lead and lead alloys.11 A.1 Introduction.11 A.2 General.11 A.3 Details of the system.11 A.3.1 General.11 A.3.2 Structure of number.11 A.4 Allocation and administration of material numbers.12

Environment: Studies into construction and demolition waste carried out by Enviros Aspinall have shown that the recycling rate of the product is above 90 %. Recommendations have been included within this standard on good management of surplus material during construction. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

In this European Standard, the performance of the product has been defined as far as possible in terms of a number of type tests. The performance of a building element made with these products depends not only on the properties of the product as it is required by this European standard, but also on the design and quality of the fabrication of the building element and on the design, construction and behaviour of the part of the building concerned in relation to the environment and conditions of use. The lead sheet supplied shall be specified and used according to the National Code of Practice, depending on service conditions such as exposure to direct sunlight and the area of the piece of lead to be fixed.

No requirements for supporting construction, design of roof or cladding systems and methods of joining are included. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 11014-1, Safety data sheet for chemical products – Part 1: Content and order of sections 3 Terms and definitions For the purposes of this European Standard, the following term and definition applies.
rolled
...