iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 12517:1999/A1:2004/AC:2004

(Amendment)

Non-destructive examination of welds - Radiographic examination of welded joints - Acceptance levels

Non-destructive examination of welds - Radiographic examination of welded joints - Acceptance levels

DIN - Translation mistake, Table 2, 5th line

Zerstörungsfreie Prüfung von Schweißverbindungen - Durchstrahlungsprüfung von Schweißverbindungen - Zulässigkeitsgrenzen

Contrôle non destructif des assemblages soudés - Contrôle par radiographie des assemblages soudés - Niveaux d'acceptation

Neporušitvena preiskava zvarov - Radiografska preiskava zvarnih spojev - Stopnje sprejemljivosti

General Information

Status
Withdrawn
Publication Date
31-May-2004
Withdrawal Date
30-Jun-2006
ICS
25.160.40 - Welded joints and welds
Technical Committee
VAR - Welding
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-Jul-2006
Due Date
01-Jul-2006
Completion Date
01-Jul-2006
Directive
97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
Mandate
M/071 - Mandate to CEN for standardization in the field of Pressure equipment
Ref Project
EN 12517:1998/A1:2002/AC:2003 - Non-destructive examination of welds - Radiographic examination of welded joints - Acceptance levels

Relations

Replaced By
SIST EN 12517-1:2006 - Non-destructive testing of welds - Part 1: Evaluation of welded joints in steel, nickel, titanium and their alloys by radiography - Acceptance levels
Effective Date
01-Jul-2006
Corrects
SIST EN 12517:1999/A1:2003 - Non-destructive testing of welds - Radiographic testing of welded joints - Acceptance levels
Effective Date
01-Jun-2004

Buy Standard

EN 12517:1999/A1:2004/AC:2004EN 12517:1999/A1:2004/AC:2004
PreviousNext
Corrigendum
EN 12517:1999/A1:2004/AC:2004
German language
2 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Neporušitvena preiskava zvarov - Radiografska preiskava zvarnih spojev - Stopnje sprejemljivostiZerstörungsfreie Prüfung von Schweißverbindungen - Durchstrahlungsprüfung von Schweißverbindungen - ZulässigkeitsgrenzenContrôle non destructif des assemblages soudés - Contrôle par radiographie des assemblages soudés - Niveaux d'acceptationNon-destructive examination of welds - Radiographic examination of welded joints - Acceptance levels25.160.40Varjeni spoji in variWelded jointsICS:Ta slovenski standard je istoveten z:EN 12517:1998/A1:2002/AC:2003SIST EN 12517:1999/A1:2004/AC:2004de01-junij-2004SIST EN 12517:1999/A1:2004/AC:2004SLOVENSKI
STANDARD



SIST EN 12517:1999/A1:2004/AC:2004



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12517:1998/A1:2002/ACDecember 2003Décembre 2003Dezember 2003ICS 25.160.40English versionVersion FrançaiseDeutsche FassungNon-destructive examination of welds - Radiographicexamination of welded joints - Acceptance levelsContrôle non destructif des assemblages soudés - Contrôle parradiographie des assemblages soudés - Niveaux d'acceptationZerstörungsfreie Prüfung von Schweißverbindungen -Durchstrahlungsprüfung von Schweißverbindungen -ZulässigkeitsgrenzenThis corrigendum becomes effective on 17 December 2003
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 5173:2023(Main)
Destructive tests on welds in metallic materials - Bend tests (ISO 5173:2023)
EN ISO 5173:2023

This document specifies a method for making transverse root, face and side bend tests on test specimens taken from butt welds, butt welds with cladding (subdivided into welds in clad plates and clad welds) and cladding without butt welds, in order to reveal imperfections on or near the surface of the test specimen which is under tension during bend testing and/or assess ductility. It also gives the dimensions of the test specimen.
In addition, this document specifies methods to be used instead of transverse bend tests with a former for welded joints when base materials, heat affected zones and/or weld metal have a significant difference in their physical and mechanical properties in relation to bending.
This document applies to metallic materials in all forms of product with welded joints made by any welding process.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 5817:2023(Main)
Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections (ISO 5817:2023)
EN ISO 5817:2023

This document specifies quality levels of imperfections in fusion-welded joints (except for beam welding) in all types of steel, nickel, titanium and their alloys. It applies to material thickness ≥ 0,5 mm. It covers fully penetrated butt welds and all fillet welds. Its principles can also be applied to partial-penetration butt welds.
Quality levels for beam-welded joints in steel are presented in ISO 13919-1.
Three quality levels are given in order to permit application to a wide range of welded fabrication. They are designated by symbols B, C and D. Quality level B corresponds to the highest requirement on the finished weld.
Several types of loads are considered, e.g. static load, thermal load, corrosion load, pressure load. Additional guidance on fatigue loads is given in Annex B.
The quality levels refer to production and good workmanship.
This document is applicable to:
a)       non-alloy and alloy steels;
b)       nickel and nickel alloys;
c)        titanium and titanium alloys;
d)       manual, mechanized and automatic welding;
e)       all welding positions;
f)         all types of welds, e.g. butt welds, fillet welds and branch connections;
g)       the following welding processes and their sub-processes, as defined in ISO 4063:
—     11 metal arc welding without gas protection;
—     12 submerged arc welding;
—     13 gas-shielded metal arc welding;
—     14 gas-shielded arc welding with non-consumable tungsten electrode;
—     15 plasma arc welding;
—     31 oxyfuel gas welding (for steel only).
Metallurgical aspects, such as grain size and hardness, are not covered by this document.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 17636-2:2023(Main)
Non-destructive testing of welds - Radiographic testing - Part 2: X- and gamma-ray techniques with digital detectors (ISO 17636-2:2022)
EN ISO 17636-2:2022

This document specifies techniques of digital radiography with the object of enabling satisfactory and repeatable results. The techniques are based on generally recognized practice and fundamental theory of the subject.
This document applies to the digital radiographic testing of fusion welded joints in metallic materials. It applies to the joints of plates and pipes. Besides its conventional meaning, “pipe”, as used in this document, covers other cylindrical bodies such as tubes, penstocks, boiler drums and pressure vessels.
This document specifies the requirements for digital radiographic X- and gamma-ray testing by either computed radiography (CR) or radiography with digital detector arrays (DDAs) of the welded joints of metallic plates and tubes for the detection of imperfections. It includes manual and automated inspection with DDAs.
Digital detectors provide a digital grey value image which can be viewed and evaluated using a computer (Annex E). This document specifies the recommended procedure for detector selection and radiographic practice. Selection of computer, software, monitor, printer and viewing conditions are important, but are not the main focus of this document. The procedure specified in this document provides the minimum requirements for radiographic practice which permits exposure and acquisition of digital radiographs with equivalent sensitivity for the detection of imperfections as film radiography (specified in ISO 17636-1).
This document does not specify acceptance levels for any of the indications found on the digital radiographs. ISO 10675 provides information on acceptance levels for weld inspection.
If contracting parties apply lower test criteria, it is possible that the quality achieved will be significantly lower than when this document is strictly applied.

  • Standard
    73 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    72 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 10447:2023(Main)
Resistance welding - Testing of welds - Peel and chisel testing of resistance spot and projection welds (ISO 10447:2022)
EN ISO 10447:2022

This document specifies the procedures and recommended tooling to be used for peel and chisel testing of resistance spot and embossed projection welds. This document applies to welds made in two or more sheets in the thickness range of 0,5 mm to 3,0 mm.
The aim of these tests is to determine:
—    weld size and failure mode when welds are destructively tested;
—    verification of welds by non-destructive chisel tests.
NOTE      The preferred method of peel testing seam welds (mechanized peel testing) is covered in ISO 14270.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 4761:2023(Main)
Non-destructive testing of welds - Phased array ultrasonic testing (UT-PA) for thin-walled steel components - Acceptance levels (ISO 4761:2022)
EN ISO 4761:2022

This document specifies acceptance levels for the phased array ultrasonic testing technique (UT-PA) of full-penetration welds in low-alloy and/or fine-grained steels in the wall thickness range from 3,2 mm to 8 mm which correspond to the quality levels of ISO 5817.
These acceptance levels are applicable to indications detected according to ISO 20601.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 17636-1:2023(Main)
Non-destructive testing of welds - Radiographic testing - Part 1: X- and gamma-ray techniques with film (ISO 17636-1:2022)
EN ISO 17636-1:2022

This document specifies techniques of radiographic testing of fusion-welded joints in metallic materials using industrial radiographic film techniques with the object of enabling satisfactory and repeatable results. The techniques are based on generally recognized practice and fundamental theory of the subject.
It applies to the joints of plates and pipes in metallic materials. Besides its conventional meaning, “pipe” as used in this document covers other cylindrical bodies, such as tubes, penstocks, boiler drums and pressure vessels.
This document does not specify acceptance levels for any of the indications found on the radiographs. The ISO 10675 series provides information on acceptance levels for weld evaluation.
If contracting parties apply lower test criteria, it is possible that the quality achieved will be significantly lower than when this document is strictly applied.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 4136:2022(Main)
Destructive tests on welds in metallic materials - Transverse tensile test (ISO 4136:2022)
EN ISO 4136:2022

This document specifies the sizes of test specimen and the procedure for carrying out transverse tensile
tests in order to determine the tensile strength and the location of fracture of a welded butt joint.
This document applies to metallic materials in all forms of product with joints made by any welded butt
joint.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 17639:2022(Main)
Destructive tests on welds in metallic materials - Macroscopic and microscopic examination of welds (ISO 17639:2022)
EN ISO 17639:2022

This document gives recommendations for specimen preparation, test procedures and their main
objectives for macroscopic and microscopic examination.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 9016:2022(Main)
Destructive tests on welds in metallic materials - Impact tests - Test specimen location, notch orientation and examination (ISO 9016:2022)
EN ISO 9016:2022

This document specifies the method to be used when describing test specimen location and notch
orientation for the testing and reporting of impact tests on welded butt joints.
This document applies to impact tests on metallic materials in all forms of product made by any fusion
and pressure welding process.
It is used in addition to the ISO 148 series and includes test specimen denomination and additional
reporting requirements.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 10675-2:2022(Main)
Non-destructive testing of welds - Acceptance levels for radiographic testing - Part 2: Aluminium and its alloys (ISO 10675-2:2021)
EN ISO 10675-2:2021

This document specifies acceptance levels for indications from imperfections in aluminium butt welds
detected by radiographic testing. If agreed, the acceptance levels can be applied to other types of welds
(such as fillet welds etc.) or materials.
The acceptance levels can be related to welding standards, application standards, specifications or
codes. This document assumes that the radiographic testing has been carried out in accordance with
ISO 17636-1 for RT-F (F = film) or ISO 17636-2 for RT-S (S = radioscopy) and RT-D (D = digital detectors)

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day