SIST EN 14306:2016
(Main)Thermal insulation products for building equipment and industrial installations - Factory made calcium silicate (CS) products - Specification
Thermal insulation products for building equipment and industrial installations - Factory made calcium silicate (CS) products - Specification
This European Standard specifies the requirements for factory made calcium silicate products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately - 170 °C to + 1 100 °C.
Calcium silicate products can be used below - 50 °C. Below the operating temperature of - 50 °C, special tests, regarding the suitability of the product in the intended application are advised (e.g. liquefaction of oxygen). Manufacturer's advice should be heeded in all cases.
The products are manufactured in the form of boards, pipe sections, segments and prefabricated ware.
This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.
Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the structural performance of systems incorporating these products is not covered.
This European Standard does not specify the required level or class of a given property that should be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender.
Products with a declared thermal conductivity greater than 0,6 W/(m·K) at 10 °C are not covered by this standard.
This European Standard does not cover products intended to be used for the insulation of the building structure.
This European Standard does not cover the following acoustical aspects: direct airborne sound insulation and impact noise transmission index.
Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus Calciumsilikat (CS) - Spezifikation
Diese Europäische Norm legt die Anforderungen an werkmäßig hergestellte Produkte aus Calciumsilikat fest, die als Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie in einem Betriebstemperaturbereich von etwa − 170 °C bis + 1 100 °C benutzt werden.
Produkte aus Calciumsilikat können unterhalb von − 50 °C verwendet werden. Bei einer Betriebstemperatur unterhalb von − 50 °C sind besondere Prüfungen bezüglich der Eignung der Produkte für den beabsichtigten Anwendungsfall ratsam (z. B. Sauerstoffverflüssigung). In jedem Fall sollten die Empfehlungen des Herstellers beachtet werden.
Die Produkte werden in Form von Platten, Rohrschalen, Segmenten und vorgeformter Dämmung her-gestellt.
Diese Europäische Norm beschreibt die Produkteigenschaften und enthält Verfahren zur Prüfung, Konformitätsbewertung, Kennzeichnung und Etikettierung.
Die von dieser Norm abgedeckten Produkte werden auch in vorgefertigten Wärmedämmsystemen und Mehr¬schicht-Verbundplatten angewendet; die Eigenschaften von Systemen, in die diese Produkte integriert sind, werden nicht behandelt.
Diese Europäische Norm legt für die einzelnen Eigenschaften keine Leistungsstufen oder -klassen fest, die ein Produkt erreichen sollte, um für einen bestimmten Anwendungsfall tauglich zu sein. Die für bestimmte Anwendungen benötigten Stufen können Regelwerken oder Ausschreibungen entnommen werden.
Diese Norm gilt nicht für Produkte mit einem Nennwert der Wärmeleitfähigkeit größer als 0,6 W/(m⋅K) bei 10 °C.
Diese Europäische Norm gilt nicht für Produkte, die zur Dämmung des Bauwerks bestimmt sind.
Diese Europäische Norm gilt nicht für die folgenden akustischen Zwecke: Luftschalldämmung und Trittschallübertragung.
Produits isolants thermiques pour l'équipement du bâtiment et les installations industrielles - Produits manufacturés en silicate de calcium (CS) - Spécification
La présente Norme européenne spécifie les exigences relatives aux produits manufacturés en silicate de calcium, utilisés pour l’isolation thermique de l’équipement du bâtiment et des installations industrielles, dont la plage de températures de service est approximativement comprise entre - 170 °C et + 1 100 °C.
Les produits en silicate de calcium peuvent être utilisés à des températures inférieures à - 50 °C. Pour une température de service inférieure à - 50 °C, des essais particuliers sont recommandés pour s'assurer de l'aptitude à l'emploi du produit dans l'application visée (liquéfaction de l'oxygène, par exemple). Il convient de se référer systématiquement aux conseils du fabricant.
Les produits sont manufacturés sous la forme de panneaux, de coquilles, de segments et de pièces préfabriquées.
La présente Norme européenne décrit les caractéristiques de ces produits et comprend des modes opératoires d’essai, d’évaluation de la conformité, de marquage et d’étiquetage.
Les produits couverts par la présente norme sont également utilisés dans les systèmes d’isolation thermique préfabriqués et les panneaux composites ; les performances structurelles des systèmes incorporant ces produits ne sont pas traitées.
La présente Norme européenne ne spécifie pas la classe ou le niveau requis d'une propriété donnée qu'il convient qu'un produit atteigne pour démontrer son aptitude à l'emploi dans une application particulière. Les niveaux requis pour une application donnée peuvent être trouvés dans les réglementations et les appels d’offre.
La présente norme ne traite pas des produits dont la conductivité thermique déclarée est supérieure à 0,6 W/(m·K) à 10 °C.
La présente Norme européenne ne couvre pas les produits destinés à être utilisés pour l’isolation des structures de bâtiments.
La présente Norme européenne ne couvre pas les critères acoustiques suivants : isolation contre le bruit aérien direct et indice de transmission du bruit d’impact.
Toplotnoizolacijski proizvodi za opremo stavb in industrijske inštalacije - Proizvodi iz kalcijevih silikatov (CS) - Specifikacija
Ta evropski standard določa zahteve za proizvode iz kalcijevih silikatov, ki se uporabljajo za toplotno izolacijo opreme stavb in industrijskih inštalacij z razponom delovne temperature približno od –170 °C do 1100 °C. OPOMBA Proizvode iz kalcijevih silikatov je mogoče uporabljati pod delovno temperaturo –50 °C. Pod delovno temperaturo –50 °C se priporočajo posebni preskusi glede primernosti proizvodov za predvideno vrsto uporabe (npr. utekočinjenje kisika). V vseh primerih naj bi upoštevali napotke proizvajalca. Proizvodi so izdelani v obliki plošč, vodovodnih odsekov, segmentov in montažne opreme. Ta standard opisuje lastnosti proizvodov ter zajema postopke za preskušanje, vrednotenje skladnosti, označevanje in etiketiranje. Proizvodi iz tega standarda se uporabljajo tudi v montažnih sistemih toplotne izolacije in vezanih ploščah; strukturne lastnosti sistemov iz teh proizvodov niso opisane. Ta standard ne določa zahtevane ravni ali razreda določene lastnosti, ki jo mora proizvod doseči, da se dokaže njegova primernost namenu za posamezno vrsto uporabe. Zahtevane ravni za posamezno uporabo je mogoče najti v uredbah in javnih razpisih. Proizvodi z deklarirano toplotno prevodnostjo, višjo od 0,6 W/mK pri 10 °C, v tem standardu niso zajeti. Ta standard ne zajema proizvodov za izolacijo stavbne strukture. Ta standard ne zajema naslednjih akustičnih vidikov: neposredne izolirnosti pred zvokom v zraku in indeksa prenosa udarnega zvoka.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Toplotnoizolacijski proizvodi za opremo stavb in industrijske inštalacije - Proizvodi iz kalcijevih silikatov (CS) - SpecifikacijaWärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus Calciumsilikat (CS) - SpezifikationProduits isolants thermiques pour l'équipement du bâtiment et les installations industrielles - Produits manufacturés en silicate de calcium (CS) - SpécificationThermal insulation products for building equipment and industrial installations - Factory made calcium silicate (CS) products - Specification91.100.60Thermal and sound insulating materialsICS:Ta slovenski standard je istoveten z:EN 14306:2015SIST EN 14306:2016en,fr,de01-februar-2016SIST EN 14306:2016SLOVENSKI
STANDARDSIST EN 14306:2010+A1:20131DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14306
December
t r s w ICS
{ sä s r rä x r Supersedes EN
s v u r xã t r r { ªA sã t r s uEnglish Version
Thermal insulation products for building equipment and products æ Specification Produits isolants thermiques pour l 5ßquipement du bâtiment et les installations industrielles æ Produits
Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie æ Werkmäßig hergestellte This European Standard was approved by CEN on
t v October
t r s wä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey andUnited Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s w CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s v u r xã t r s w ESIST EN 14306:2016
Factory production control . 20 SIST EN 14306:2016
Determination of minimum service temperature . 23 B.1 Definitions . 23 B.2 Principle . 23 B.3 Apparatus . 23 B.4 Test specimens . 24 B.5 Procedure . 24 B.6 Calculation and expression of results . 25 B.7 Accuracy of measurements . 26 B.8 Test report . 26 Annex C (informative)
Preparation of the test specimens to measure thermal conductivity . 27 C.1 Preparation of the test specimens to measure thermal conductivity . 27 C.2 Ageing . 27 Annex D (informative)
Additional properties . 28 D.1 General . 28 D.2 Coefficient of thermal expansion . 28 D.3 Apparent and true porosity . 28 D.4 Air flow resistance . 28 D.5 Creep in compression . 28 D.6 Permeability to gases . 28 D.7 Acoustic properties . 28 D.8 Bending strength . 28 D.9 Apparent density . 28 Annex ZA (informative)
Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation . 30 ZA.1 Scope and relevant characteristics . 30 ZA.2 Procedures for AVCP of factory made calcium silicate (CS) . 32 ZA.3 CE Marking and labelling . 39 Bibliography . 41 SIST EN 14306:2016
is the thermal conductivity W/(m·K) D=is the declared thermal conductivity W/(m·K) =is the water vapour diffusion resistance factor — Sb is the deviation from squareness of boards on length and width mm/m Sd is the deviation from squareness of boards on thickness mm Smax is the deviation from flatness mm 10=is the compressive stress at 10 % deformation kPa m=is the compressive strength kPa v is the deviation from squareness for pipe insulation mm a=is the apparent density kg/m3 CS(Y) is the symbol of the declared level for compressive stress at Y % deformation
CS(10) is the symbol of the declared level for compressive stress at 10 % deformation
CL is the symbol of the declared level of soluble chloride ions
F is the symbol of the declared level of soluble fluoride ions
L is the symbol of the declared class for length tolerances
MU is the symbol of the declared value for water vapour diffusion resistance factor
P is the symbol of the declared value for flatness tolerances
pH is the symbol of the declared level of the pH-value
S is the symbol of the declared class for squareness tolerances
ST(+) is the symbol of the declared level for maximum service temperature
T is the symbol of the declared class for thickness tolerances
W is the symbol of the declared class for width tolerances
3.2.2 Abbreviations used in this standard AVCP is Assessment and Verification of Constancy of Performance (previously named attestation of conformity) CS is Calcium Silicate DoP is Declaration of Performance FPC is Factory Production Control PTD is Product Type Determination (previously named ITT for Initial Type Test) RtF is Reaction to Fire ThIBEII is Thermal Insulation for Building Equipment and Industrial Installations VCP is Verification of Constancy of Performance (previously named evaluation of conformity) 4 Requirements 4.1 General Product properties shall be assessed in accordance with Clause 5. To comply with this standard, products shall meet the requirements of 4.2, and the requirements of 4.3 as appropriate. NOTE Information on additional properties is given in Annex D. One test result for a product property is the average of the measured values on the numbers of test specimens given in Table 4. 4.2 For all applications 4.2.1 Thermal conductivity For flat specimens thermal conductivity shall be based upon measurements carried out in accordance with EN 12667 and if relevant EN 12939 or EN ISO 8894-1 (this test is calibrated against EN 12667 and if relevant EN 12939). For cylindrical specimens EN ISO 8497 shall be used as specified in 5.3.2. The thermal conductivity values shall be determined by the manufacturer and verified in accordance with EN ISO 13787. They shall be declared by the manufacturer according to the above specified measurement standards covering the declared product service temperature range. The following conditions apply: — the measured values shall be expressed with three significant figures; — the declared conductivity curve shall be given as limit curve, defined in EN ISO 13787; — the values of the declared thermal conductivity, D, shall be rounded upwards to the nearest 0,001 W/(m·K); — the lowest reference mean test temperature that could be required is - 170 °C. The declared equation/limit curve is the “declared reference” with three significant figures, that is to 0,001 W/(m·K) for all
values. This shall be used as a reference for the verification of the declaration. SIST EN 14306:2016
±0,4 % a ±0,4 % a – 2 mm
Pipe section or segment ±3 mm or
+ 3 mm - 0 mm ±0,6 % a
– 2 mm + 5 mm a Whichever gives the greatest numerical tolerance. 4.2.2.2 Squareness Deviation from squareness of boards, Sb and Sd, shall be determined in accordance with EN 824 and deviation from squareness for pipe sections and segments, v in accordance with EN 13467. The deviation from squareness of boards on length and width, Sb, shall not exceed 6 mm/m and the deviation from squareness of boards on thickness, Sd, shall not exceed 2 mm. For pipe sections and segments, the deviation from squareness, v, shall not exceed 3 mm. 4.2.2.3 Flatness Deviation from flatness, Smax shall be determined in accordance with EN 825 for boards. The deviation from flatness, Smax, shall not exceed 6 mm. 4.2.2.4 Pipe section linearity Deviation from linearity, Li shall be determined in accordance with EN 13467. The deviation from linearity, Li, shall not exceed 3 mm or ± 0,6 % on length, whichever gives the greatest numerical tolerance. 4.2.3 Dimensional stability The dimensional stability under specified temperature and humidity conditions shall be determined in accordance with EN 1604. The test shall be carried out after storage for 48 h at (23 ± 2) °C and (90 ± 5) % relative humidity. The relative changes in length, l, and width, b shall not exceed 1,0 %. The relative change in thickness, d shall not exceed 1,0 %. 4.2.4 Reaction to fire of the product as placed on the market Reaction to fire classification (Euroclasses) of the product, as placed on the market, shall be determined in accordance with EN 13501-1, and the basic Mounting and Fixing rules given in EN 15715:2009. SIST EN 14306:2016
· 650 ST(+) 700
· 700 ST(+) 750
· 750 ST(+) 800
· 800 ST(+) 850
· 850 ST(+) 900
· 900 ST(+) 950
· 950 ST(+) 1 000
· 1 000 ST(+) 1 050
· 1 050 ST(+) 1 100
· 1 100 4.3.3 Minimum service temperature The minimum service temperature, ST(-), shall be declared in levels with steps of 50 °C. The minimum service temperature, ST(-), shall be determined in accordance with Annex B. At the minimum service temperature, ST(-) the relative changes in length, l, and in width, b, shall not exceed 2 %. Minimum service temperature within the scope of this standard, but above 0 °C need not be tested. 4.3.4 Compressive stress or compressive strength Compressive stress at 10 % deformation, 10, or the compressive strength, m, shall be determined in accordance with EN 826. No test result shall be lower than the value, given in Table 3, for the declared level. Table 3 — Levels for compressive stress at 10 % deformation or compressive strength Level Requirement kPa CS(10\Y) 500
· 500 CS(10\Y) 1 000
· 1 000 CS(10\Y) 1 500
· 1 500 CS(10\Y) 2 000
· 2 000 CS(10\Y) 3 000
· 3 000 CS(10\Y) 4 000
· 4 000 CS(10\Y) 5 000
· 5 000 CS(10\Y) 10 000
· 10 000 NOTE EN 826 is not applicable to pipe sections, and compression behaviour is not determined. SIST EN 14306:2016
· 300 × 300 × d 1 — EN ISO 8894-1
· 230 × 114 × d 1 —
EN ISO 8497 Full-size 1 — 4.2.2 Dimensions and tolerances
Length and width EN 822 EN 13467 Full-size 1 — Thickness EN 823 EN 13467 Full-size 1 — Inside diameter
EN 13467 Full-size 1 — 4.2.2.2 Squareness EN 824 EN 13467 Full-size 1 — 4.2.2.3 Flatness EN 825
Full-size 1 — 4.2.2.4 Pipe section linearity
EN 13467 Full-size 1 — 4.2.3 Dimensional stability EN 1604
Full size 500 × 500 × d 250 × 250 × d 200 × 200 × d 1 3 3 3 — — — — 4.2.4 Reaction to fire EN 13501–1 EN 15715 4.3.2 Maximum service temperature EN 1094–6 EN 1094–6 100 × 100 × d for pipe sections, see EN 1094–6 3 see 5.3.3 4.3.3 Minimum service temperature Annex B
See Annex B 1 — 4.3.4 Compressive stress or compressive strength EN 826 EN 826 see 6.1 in EN 826 3 — 4.3.5 Trace quantities of water soluble chlorides and the pH-value EN 13468
— 3 20 g 4.3.6 Water vapour diffusion resistance EN 12086 EN 13469 see 6.1 in EN 12086 3 —
see 6.2 in EN 13469 3 see 6.1 in EN 13469 4.3.7 Short-term water absorption Preformed pipe insulation EN 1609
EN 13472 200 × 200 × d 4 4 — — 4.3.8 Release of dangerous substances b b — — — 4.3.9 Continuous glowing combustion b b
a Full-size product thickness, except for 4.2.3. b Not yet available. SIST EN 14306:2016
of the range. For PTD, measurements of thermal conductivity made on two internal diameters of pipe sections at the greatest and smallest insulation thickness for each set of the diameters are deemed to be representative of the total product range. For FPC, one dimension only is used. NOTE Suitable sizes are 48 mm and 194 mm internal diameter. The guarded hot plate method EN 12939 or the hot wire methods EN ISO 8894-1 shall be deemed to be a suitable method for measurement of pipe sections having a diameter exceeding 500 mm. Flat slabs shall be prepared having the same thickness and density as the sections. 5.3.3 Maximum service temperature 5.3.3.1 General Maximum service temperature shall be determined in accordance with EN 1094-6 at the declared maximum service temperature with the exception that the minimum test temperature shall be 650 °C. Specimens for testing the maximum service temperature of pipe sections and segments may be cut from flat boards with the same composition and density as the pipe section or segment product. 5.3.3.2 Test specimens The test specimens shall be square cut with a cross section of 100 mm × 100 mm. The thickness shall be always product thickness for all applications. 5.3.4 Reaction to fire The tests shall be carried out in accordance with the rules given in EN 13501-1. Rules for mounting and fixing are given in EN 15715:2009. SIST EN 14306:2016
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...