oSIST prEN 16307-2:2021

SLOVENSKI STANDARD
oSIST prEN 16307-2:2021
01-december-2021
Vozila za talni transport - Varnostne zahteve in preverjanje - 2. del: Dodatne
zahteve za vozila za talni transport z lastnim pogonom z mehanizmom za dviganje
s spremenljivim dosegom
Industrial trucks - Safety requirements and verification - Part 2: Supplementary
requirements for self-propelled variable-reach trucks
Flurförderzeuge - Sicherheitstechnische Anforderungen und Verifizierung - Teil 2:
Zusätzliche Anforderungen für motorkraftbetriebene Flurförderzeuge mit veränderlicher
Reichweite
Chariots de manutention - Exigences de sécurité et vérification - Partie 2 : Exigences
supplémentaires pour les chariots automoteurs à portée variable
Ta slovenski standard je istoveten z: prEN 16307-2
ICS:
53.060 Industrijski tovornjaki Industrial trucks
oSIST prEN 16307-2:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 16307-2:2021

---------------------- Page: 2 ----------------------
oSIST prEN 16307-2:2021


DRAFT
EUROPEAN STANDARD
prEN 16307-2
NORME EUROPÉENNE

EUROPÄISCHE NORM

October 2021
ICS 53.060
English Version

Industrial trucks - Safety requirements and verification -
Part 2: Supplementary requirements for self-propelled
variable-reach trucks
Chariots de manutention - Exigences de sécurité et Flurförderzeuge - Sicherheitstechnische
vérification - Partie 2 : Exigences supplémentaires pour Anforderungen und Verifizierung - Teil 2: Zusätzliche
les chariots automoteurs à portée variable Anforderungen für motorkraftbetriebene
Flurförderzeuge mit veränderlicher Reichweite
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 150.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16307-2:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 16307-2:2021
prEN 16307-2:2021 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Safety requirements and/or protective/risk reduction measures . 6
4.1 General. 6
4.2 Electrical requirements . 6
4.3 Operator's seat . 6
4.4 Protection against crushing, shearing and trapping . 6
4.5 Longitudinal stability determination . 7
4.6 Visibility . 7
4.7 Reduction of noise by design . 7
4.7.1 General. 7
4.7.2 Main source of noise . 7
4.7.3 Measures to reduce noise at the operator's position . 7
4.7.4 Determination of noise emission values . 8
4.8 Vibration . 8
4.9 Electromagnetic radiation . 8
4.9.1 General. 8
4.9.2 Non-ionising radiation . 8
4.9.3 External radiation . 8
5 Verification of safety requirements and/or protective/risk reduction measures . 8
6 Information for use . 8
6.1 Instruction handbook(s) . 8
6.1.1 Truck/ attachments . 8
6.1.2 Operation of truck . 8
6.1.3 Transportation, commissioning and storage . 9
6.2 Marking – Information plates . 9
Annex A (informative) List of significant hazards . 10
Bibliography . 12

2

---------------------- Page: 4 ----------------------
oSIST prEN 16307-2:2021
prEN 16307-2:2021 (E)
European foreword
This document (prEN 16307-2:2021) has been prepared by Technical Committee CEN/TC 150
“Industrial trucks - Safety”, the secretariat of which is held by BSI.
This document is currently submitted to the CEN Enquiry.
This document is based on ISO/TS 3691-7:2011 “Industrial trucks — Safety requirements and
verification — Part 7: Regional requirements for countries within the European Community” and is
limited to self-propelled industrial trucks.
EN 16307 consists of the following parts, under the general title “Industrial trucks — Safety requirements
and verification”:
— Part 1: “Supplementary requirements for self-propelled industrial trucks, other than driverless
trucks, variable-reach trucks and burden-carrier trucks”;
— Part 2: “Supplementary requirements for self-propelled variable-reach trucks”;
— Part 3: “Supplementary requirements for trucks with elevating operator position and trucks
specifically designed to travel with elevated loads (additional requirements to EN 16307-1)”;
— Part 5: “Supplementary requirements for pedestrian-propelled trucks”;
— Part 6: “Supplementary requirements for burden and personnel carriers”.
1
This document is intended to be used with EN ISO 3691-2:— “Industrial trucks — Safety requirements
and verification: Part: 2: self-propelled variable-reach trucks”.

1
Under preparation. Current stage is: prEN ISO 3691-2:2021.
3

---------------------- Page: 5 ----------------------
oSIST prEN 16307-2:2021
prEN 16307-2:2021 (E)
Introduction
General
This document is a type-C standard as stated in EN ISO 12100:2010.
This document is of relevance, in particular, for the following stakeholder groups representing the market
players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);
— health and safety bodies (regulators, accident prevention organizations, market surveillance,
etc.).
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);
— machine users/employees (e.g. trade unions, organizations for people with special needs);
— service providers, e.g. for maintenance (small, medium and large enterprises).
The above-mentioned stakeholder groups have been given the possibility to participate in the drafting
process of this document.
The machines concerned and the extent to which hazards, hazardous situations or hazardous events are
covered are indicated in the Scope of this document.
When requirements of this type-C standard are different from those which are stated in type-A or type-B
standards, the requirements of this type-C standard take precedence over the requirements of the other
standards for machines that have been designed and built according to the requirements of this type-C
standard.
The EN 16307 series of standards covers safety requirements and their verification for industrial trucks
as defined in ISO 5053-1:2020 that are not covered exhaustively by EN ISO 3691 series.
4

---------------------- Page: 6 ----------------------
oSIST prEN 16307-2:2021
prEN 16307-2:2021 (E)
1 Scope
This document gives requirements for the types of industrial trucks specified in the scope of
1
EN ISO 3691-2:— .
1
This document is intended to be used in conjunction with EN ISO 3691-2:— . These requirements are
1
supplementary to those stated in EN ISO 3691-2:— .
This document deals with the following supplementary requirements and significant hazards, hazardous
situations or hazardous events relevant, when it is used as intended and under conditions of misuse
which are reasonably foreseeable by the manufacturer:
— electrical requirements;
— noise emissions;
— vibration;
— electromagnetic radiation.
1
This document defines supplementary requirements to EN ISO 3691-2:— :
— operator's seat;
— protection against crushing, shearing and trapping;
— longitudinal stability determination;
— visibility;
— information for use (instruction handbook and marking).
Annex A (informative) contains the list of significant hazards covered by this document.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1175:2020, Safety of industrial
...