iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN ISO 22007-1:2024

(Main)

Plastics - Determination of thermal conductivity and thermal diffusivity - Part 1: General principles (ISO 22007-1:2024)

Plastics - Determination of thermal conductivity and thermal diffusivity - Part 1: General principles (ISO 22007-1:2024)

This document describes the background to methods for the determination of the thermal conductivity
and thermal diffusivity of polymeric materials. Different techniques are available for these measurements
and some can be better suited than others for a particular type, state and form of material. This document
provides a broad overview of these techniques. Standards specific to these techniques, as referenced in this
document, are used to carry out the actual test method.

Kunststoffe - Bestimmung der Wärmeleitfähigkeit und der Temperaturleitfähigkeit - Teil 1: Allgemeine Grundlagen (ISO 22007-1:2024)

In diesem Dokument werden die Grundlagen für Verfahren zur Bestimmung der Wärmeleitfähigkeit und Temperaturleitfähigkeit polymerer Werkstoffe beschrieben. Für diese Messungen stehen unterschiedliche Verfahren zur Verfügung, und für einen bestimmten Werkstofftyp, eine bestimmte Werkstoffbeschaffenheit oder -form können einige Verfahren geeigneter als andere sein. Dieses Dokument gibt einen umfassenden Überblick über diese Verfahren. Die für diese Verfahren entwickelten Normen werden entsprechend den Verweisungen in diesem Dokument für die Durchführung des jeweiligen Prüfverfahrens angewendet.
SICHERHEITSHINWEIS — Die Anwender dieses Dokuments sollten, falls zutreffend, mit der üblichen Laborpraxis vertraut sein. Dieses Dokument beansprucht nicht, sämtliche mit seiner Anwendung verbundenen Sicherheitsprobleme, soweit diese gegeben sind, zu behandeln. Es liegt in der Verantwortung des Anwenders, die angemessenen Maßnahmen in Bezug auf den Gesundheits- und Arbeitsschutz einzuleiten und die Einhaltung jeglicher gesetzlicher Anforderungen sicherzustellen.

Plastiques - Détermination de la conductivité thermique et de la diffusivité thermique - Partie 1: Principes généraux (ISO 22007-1:2024)

L'ISO 22007-1 :2017 décrit les principes de base des méthodes permettant de déterminer la conductivité thermique et la diffusivité thermique des matériaux polymères. Différentes techniques de mesurage sont disponibles et certaines peuvent être mieux adaptées que d'autres pour un type, un état et une forme particuliers du matériau. L'ISO 22007-1 :2017 donne un aperçu général de ces techniques. Les normes propres à ces techniques, telles que mentionnées dans le présent document, sont utilisées pour la mise en ?uvre de la méthode d'essai réelle.

Polimerni materiali - Ugotavljanje toplotne prevodnosti in toplotne razpršenosti - 1. del: Splošna načela (ISO 22007-1:2024)

Ta dokument opisuje ozadje metod za ugotavljanje toplotne prevodnosti
in toplotne razpršenosti polimernih materialov. Za te meritve so na voljo različne tehnike, pri čemer so nekatere lahko primernejše od drugih za posamezno vrsto, stanje in obliko materiala. Ta dokument vsebuje obsežen pregled teh tehnik. Za izvajanje dejanske preskusne metode se uporabljajo standardi za te tehnike, kakor je opisano v tem dokumentu.

General Information

Status
Published
Public Enquiry End Date
21-Jun-2023
Publication Date
11-Apr-2024
ICS
83.080.01 - Plastics in general
Technical Committee
IPMA - Polimer materials and products
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
25-Mar-2024
Due Date
30-May-2024
Completion Date
12-Apr-2024
Ref Project
EN ISO 22007-1:2024 - Plastics - Determination of thermal conductivity and thermal diffusivity - Part 1: General principles (ISO 22007-1:2024)

Relations

Revised
SIST EN ISO 22007-1:2018 - Plastics - Determination of thermal conductivity and thermal diffusivity - Part 1: General principles (ISO 22007-1:2017)
Effective Date
19-Jan-2023

Buy Standard

EN ISO 22007-1:2024EN ISO 22007-1:2024
PreviousNext
Standard
EN ISO 22007-1:2024
English language
26 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
prEN ISO 22007-1:2023prEN ISO 22007-1:2023
PreviousNext
Draft
prEN ISO 22007-1:2023
English language
22 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 22007-1:2024
01-maj-2024
Polimerni materiali - Ugotavljanje toplotne prevodnosti in toplotne razpršenosti - 1.
del: Splošna načela (ISO 22007-1:2024)
Plastics - Determination of thermal conductivity and thermal diffusivity - Part 1: General
principles (ISO 22007-1:2024)
Kunststoffe - Bestimmung der Wärmeleitfähigkeit und der Temperaturleitfähigkeit - Teil
1: Allgemeine Grundlagen (ISO 22007-1:2024)
Plastiques - Détermination de la conductivité thermique et de la diffusivité thermique -
Partie 1: Principes généraux (ISO 22007-1:2024)
Ta slovenski standard je istoveten z: EN ISO 22007-1:2024
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 22007-1:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 22007-1:2024

---------------------- Page: 2 ----------------------
SIST EN ISO 22007-1:2024


EN ISO 22007-1
EUROPEAN STANDARD

NORME EUROPÉENNE

March 2024
EUROPÄISCHE NORM
ICS 83.080.01 Supersedes EN ISO 22007-1:2017
English Version

Plastics - Determination of thermal conductivity and
thermal diffusivity - Part 1: General principles (ISO 22007-
1:2024)
Plastiques - Détermination de la conductivité Kunststoffe - Bestimmung der Wärmeleitfähigkeit und
thermique et de la diffusivité thermique - Partie 1: der Temperaturleitfähigkeit - Teil 1: Allgemeine
Principes généraux (ISO 22007-1:2024) Grundlagen (ISO 22007-1:2024)
This European Standard was approved by CEN on 6 March 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22007-1:2024 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 22007-1:2024
EN ISO 22007-1:2024 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 22007-1:2024
EN ISO 22007-1:2024 (E)
European foreword
This document (EN ISO 22007-1:2024) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2024, and conflicting national standards
shall be withdrawn at the latest by September 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 22007-1:2017.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 22007-1:2024 has been approved by CEN as EN ISO 22007-1:2024 without any
...

SLOVENSKI STANDARD
oSIST prEN ISO 22007-1:2023
01-maj-2023
Polimerni materiali - Ugotavljanje toplotne prevodnosti in toplotne razprševalnosti
- 1. del: Splošna načela (ISO/DIS 22007-1:2023)
Plastics - Determination of thermal conductivity and thermal diffusivity - Part 1: General
principles (ISO/DIS 22007-1:2023)
Kunststoffe - Bestimmung der Wärmeleitfähigkeit und der Temperaturleitfähigkeit - Teil
1: Allgemeine Grundlagen (ISO/DIS 22007-1:2023)
Plastiques - Détermination de la conductivité thermique et de la diffusivité thermique -
Partie 1: Principes généraux (ISO/DIS 22007-1:2023)
Ta slovenski standard je istoveten z: prEN ISO 22007-1
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
oSIST prEN ISO 22007-1:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 22007-1:2023

---------------------- Page: 2 ----------------------
oSIST prEN ISO 22007-1:2023
DRAFT INTERNATIONAL STANDARD
ISO/DIS 22007-1
ISO/TC 61/SC 5 Secretariat: DIN
Voting begins on: Voting terminates on:
2023-03-31 2023-06-23
Plastics — Determination of thermal conductivity and
thermal diffusivity —
Part 1:
General principles
Plastiques — Détermination de la conductivité thermique et de la diffusivité thermique —
Partie 1: Principes généraux
ICS: 83.080.01
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 22007-1:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

---------------------- Page: 3 ----------------------
oSIST prEN ISO 22007-1:2023
ISO/DIS 22007-1:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 22007-1
ISO/TC 61/SC 5 Secretariat: DIN
Voting begins on: Voting terminates on:

Plastics — Determination of thermal conductivity and
thermal diffusivity —
Part 1:
General principles
Plastiques — Détermination de la conductivité thermique et de la diffusivité thermique —
Partie 1: Principes généraux
ICS: 83.080.01
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 22007-1:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
  © ISO 2023 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

---------------------- Page: 4 ----------------------
oSIST prEN ISO 22007-1:2023
ISO/DIS 22007-1:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 22007-4:2024(Main)
Plastics - Determination of thermal conductivity and thermal diffusivity - Part 4: Light flash method (ISO 22007-4:2024)
EN ISO 22007-4:2024

This document specifies a method for the determination of the thermal diffusivity of a thin solid disc of
plastics in the thickness direction by the light flash method. This method is based upon the measurement of
the temperature rise at the rear face of the thin-disc specimen produced by a short energy pulse on the front
face.
The method is applicable to homogeneous solid plastics as well as composites having an isotropic
or orthotropic structure. In general, it covers materials having a thermal diffusivity, α, in the range
1 × 10−7 m2⋅s−1 < α < 1 × 10−4 m2⋅s−1. Measurements can be carried out in gaseous and vacuum environments
over a temperature range from −100 °C to +400 °C.
NOTE For inhomogeneous specimens, the measured values can be specimen thickness dependent.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 20753:2024(Main)
Plastics - Test specimens (ISO 20753:2023)
EN ISO 20753:2023

This document specifies dimensional requirements relating to test specimens prepared from plastics materials intended for processing by moulding, as well as to test specimens prepared by machining from sheets or shaped articles. It compiles the designations and dimensions of test specimens used for the acquisition of comparable data and also of other frequently used specimens.
The following types of test specimen are specified:
a) Type A1 and type A2 specimens (1 = injection moulded, 2 = machined from a sheet or shaped article)
These are tensile test specimens from which, with simple machining, specimens for a variety of other tests can be taken (see Annex A).
The type A1 specimen is a multipurpose test specimen. The principal advantage of a multipurpose test specimen is that it allows all the test methods mentioned in Annex A to be carried out by all test laboratories on the basis of comparable mouldings. Consequently, the properties measured are coherent as all are measured using similar specimens prepared in the same way. In other words, it can be expected that test results for a given set of specimens will not vary appreciably due to unintentionally different moulding conditions. On the other hand, if desired, the influence of moulding conditions and/or different states of the specimens can be assessed without difficulty for all of the properties measured.
Also described are reduced-scale test specimens designated type Axy, where x is the number indicating the method of specimen preparation (1 = injection moulded, 2 = machined from a sheet or shaped article) and y is a number indicating the scale factor (1:y). These can be used e.g. when full-sized test specimens are not convenient or when sample material exists in small quantities only.
b) Type B specimens
These are bar specimens which can be directly moulded or can be machined from the central section of type A1 specimens or from sheets or shaped articles.
c) Type C specimens
These are small tensile test specimens which can be directly moulded or machined, e.g. from plates (Type D or type F specimens), from the central section of type A1 specimens or from sheets or shaped articles.
d) Type D1 and type D2 specimens
These are square plates of thickness 1 mm and 2 mm, respectively.
e) Type F specimens
These are rectangular plates intended for use in the analysis of mechanical anisotropy.
If a particular type of test specimen is not mentioned in this document, this does not mean that there is any intention to exclude the use of the specimen. Additional specimen types can be added in future if they are commonly used.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 8256:2024(Main)
Plastics - Determination of tensile-impact strength (ISO 8256:2023)
EN ISO 8256:2023

ISO 8256:2004 specifies two methods (method A and method B) for the determination of the tensile-impact strength of plastics under defined conditions. The tests can be described as tensile tests at relatively high strain rates. These methods can be used for rigid materials (as defined in ISO 472), but are especially useful for materials too flexible or too thin to be tested with impact tests conforming to ISO 179 or ISO 180.
These methods are used for investigating the behaviour of specified specimens under specified impact velocities, and for estimating the brittleness or the toughness of specimens within the limitations inherent in the test conditions.
These methods are applicable both to specimens prepared from moulding materials and to specimens taken from finished or semi-finished products (for example mouldings, films, laminates, or extruded or cast sheets).
Results obtained by testing moulded specimens of different dimensions may not necessarily be the same. Equally, specimens cut from moulded products may not give the same results as specimens of the same dimensions moulded directly from the material. Test results obtained from specimens prepared from moulding compounds cannot be applied directly to mouldings of any given shape, because values may depend on the design of the moulding and the moulding conditions. Results obtained by method A and method B may or may not be comparable.
These methods are not suitable for use as a source of data for design calculations on components. Information on the typical behaviour of a material can be obtained, however, by testing different types of test specimen prepared under different conditions, and by testing at different temperatures. The two different methods are suitable for production control as well as for quality control.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 61:2023(Main)
Plastics - Determination of apparent density of moulding material that cannot be poured from a specified funnel (ISO 61:2023)
EN ISO 61:2023

A portion of 60 g of loose moulding material is dropped little by little into a measuring cylinder as evenly distributed as possible. A plunger with specified mass fitting to the measuring cylinder is slowly lowered until it is entirely supported by the material. After 1 min the volume of the material with the plunger resting upon it, shall be determined and the apparent density shall be calculated.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 24187:2023(Main)
Principles for the analysis of microplastics present in the environment (ISO 24187:2023)
EN ISO 24187:2023

Development of technical principles, which will be used across the board for future standardization
projects on testing methods for plastics and microplastics in various matrices (in particular water, soil,
compost, sewage sludge, biota). This includes the following::
- Description of necessary working conditions in the laboratory
- Description of necessary working conditions in the field
- safety instructions
- Proposals for harmonisation of size classes to be considered
- Proposals to harmonise the indication of results
- Notes on matrix-specific particularities with regard to the representativeness of the results

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 20200:2023(Main)
Plastics - Determination of the degree of disintegration of plastic materials under composting conditions in a laboratory-scale test (ISO 20200:2023)
EN ISO 20200:2023

This document specifies a method of determining the degree of disintegration of plastic materials when exposed to a laboratory-scale composting environment. The method is not applicable to the determination of the biodegradability of plastic materials under composting conditions. Further testing is necessary to be able to claim compostability.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 13927:2023(Main)
Plastics - Simple heat release test using a conical radiant heater and a thermopile detector (ISO 13927:2023)
EN ISO 13927:2023

This document specifies a method suitable for the production control or product development purposes for assessing the heat release rate of essentially flat products exposed in the horizontal orientation to controlled levels of radiant heating with an external igniter. The heat release rate is determined by the use of a thermopile instead of the more accurate oxygen consumption techniques. The time to ignition and sustained flaming are also measured in this test. The mass loss of the test specimen can also be measured optionally.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 6186:2023(Main)
Plastics - Determination of pourability (ISO 6186:2023)
EN ISO 6186:2023

This document specifies two methods, A and B, for determining the pourability of plastics in powdered and granular form, by measuring the flow time through a funnel under specified conditions.
From method A, information concerning the processability can be derived, whilst method B is especially designed for process control during manufacture.
The methods specified are not necessarily applicable to all plastics in powdered and granular form.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 180:2023(Main)
Plastics - Determination of Izod impact strength (ISO 180:2023)
EN ISO 180:2023

1.1 This document specifies a method for determining the Izod impact strength of plastics under defined conditions. A number of different types of specimen and test configurations are defined. Different test parameters are specified according to the type of material, the type of test specimen and the type of notch.
1.2 The method is used to investigate the behaviour of specified types of specimen under the impact conditions defined and for estimating the brittleness or toughness of specimens within the limitations inherent in the test conditions.
1.3 The method is suitable for use with the following range of materials:
— rigid thermoplastic moulding and extrusion materials, including filled and reinforced compounds in addition to unfilled types; rigid thermoplastics sheets;
— rigid thermosetting moulding materials, including filled and reinforced compounds; rigid thermosetting sheets, including laminates;
— fibre-reinforced thermosetting and thermoplastic composites incorporating unidirectional or non-unidirectional reinforcements such as mat, woven fabrics, woven rovings, chopped strands, combination and hybrid reinforcements, rovings and milled fibres and sheet made from pre-impregnated materials (prepregs);
— thermotropic liquid-crystal polymers.
1.4 The method is not normally suitable for use with rigid cellular materials and sandwich structures containing cellular material. Notched specimens are also not normally used for long-fibre-reinforced composites or thermotropic liquid-crystal polymers.
1.5 The method is suited to the use of specimens which can be either moulded to the chosen dimensions, machined from the central portion of a standard multipurpose test specimen (see ISO 20753) or machined from finished or semi-finished products such as mouldings, laminates and extruded or cast sheet.
1.6 The method specifies preferred dimensions for the test specimen. Tests which are carried out on specimens of different dimensions or with different notches, or specimens which are prepared under different conditions, may produce results which are not comparable. Other factors, such as the energy capacity of the apparatus, its impact velocity and the conditioning of the specimens can also influence the results. Consequently, when comparative data are required, these factors are to be carefully controlled and recorded.
1.7 The method is not intended to be used as a source of data for design calculations. Information on the typical behaviour of a material can be obtained, however, by testing at different temperatures, by varying the notch radius and/or the thickness and by testing specimens prepared under different conditions.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 179-1:2023(Main)
Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2023)
EN ISO 179-1:2023

ISO 179-1:2010 specifies a method for determining the Charpy impact strength of plastics under defined conditions. A number of different types of specimen and test configurations are defined. Different test parameters are specified according to the type of material, the type of test specimen and the type of notch.
The method can be used to investigate the behaviour of specified types of specimen under the impact conditions defined and for estimating the brittleness or toughness of specimens within the limitations inherent in the test conditions. It can also be used for the determination of comparative data from similar types of material.
The method has a greater range of applicability than that given in ISO 180 (Izod impact testing) and is more suitable for the testing of materials showing interlaminar shear fracture or of materials exhibiting surface effects due to environmental factors.
The method is suitable for use with the following range of materials:
rigid thermoplastic moulding and extrusion materials (including filled and reinforced compounds in addition to unfilled types) and rigid thermoplastics sheets;
rigid thermosetting moulding materials (including filled and reinforced compounds) and rigid thermosetting sheets (including laminates);
fibre-reinforced thermosetting and thermoplastic composites incorporating unidirectional or multi-directional reinforcements (such as mats, woven fabrics, woven rovings, chopped strands, combination and hybrid reinforcements, rovings and milled fibres) or incorporating sheets made from pre-impregnated materials (prepregs), including filled compounds;
thermotropic liquid-crystal polymers.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day