SIST EN ISO 10472-3:2008

SLOVENSKI STANDARD
SIST EN ISO 10472-3:2008
01-december-2008
1DGRPHãþD
SIST EN ISO 10472-3:2000
9DUQRVWQH]DKWHYH]DLQGXVWULMVNHVWURMH]DQHJRSHULODGHO7XQHOVNHOLQLMH]D
SUDQMHYNOMXþQRVVWURMLNRPSRQHQWDPL,62
Safety requirements for industrial laundry machinery - Part 3: Washing tunnel lines
including component machines (ISO 10472-3:1997)
Sicherheitsanforderungen für industrielle Wäschereimaschinen - Teil 3:
Durchlaufwaschanlagen einschließlich Einzelmaschinen (ISO 10472-3:1997)
Exigences de sécurité pour les machines de blanchisserie industrielle - Partie 3: Trains
de lavage incluant les machines composantes (ISO 10472-3:1997)
Ta slovenski standard je istoveten z: EN ISO 10472-3:2008
ICS:
97.060 Aparati za nego perila Laundry appliances
SIST EN ISO 10472-3:2008 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 10472-3:2008

---------------------- Page: 2 ----------------------

SIST EN ISO 10472-3:2008
EUROPEAN STANDARD
EN ISO 10472-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2008
ICS 97.060 Supersedes EN ISO 10472-3:1997
English Version
Safety requirements for industrial laundry machinery - Part 3:
Washing tunnel lines including component machines (ISO
10472-3:1997)
Exigences de sécurité pour les machines de blanchisserie Sicherheitsanforderungen für industrielle
industrielle - Partie 3: Trains de lavage incluant les Wäschereimaschinen - Teil 3: Durchlaufwaschanlagen
machines composantes (ISO 10472-3:1997) einschließlich Einzelmaschinen (ISO 10472-3:1997)
This European Standard was approved by CEN on 12 October 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10472-3:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 10472-3:2008
EN ISO 10472-3:2008 (E)
Contents Page
Foreword.3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC .4
Annex ZB (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC .5

2

---------------------- Page: 4 ----------------------

SIST EN ISO 10472-3:2008
EN ISO 10472-3:2008 (E)
Foreword
The text of ISO 10472-3:1997 has been prepared by Technical Committee ISO/TC 72 “Textile machinery and
machinery for dry-cleaning and industrial laundering” of the International Organization for Standardization
(ISO) and has been taken over as EN ISO 10472-3:2008 by Technical Committee CEN/TC 214 “Textile
machinery and accessories” the secretariat of which is held by SNV.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2009, and conflicting national standards shall be withdrawn at the
latest by December 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10427-3:1997.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directives.
For relationship with EC Directives, see informative Annexes ZA and ZB, which are integral parts of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10472-3:1997 has been approved by CEN as a EN ISO 10472-3:2008 without any
modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 10472-3:2008
EN ISO 10472-3:2008 (E)
Annex ZA
(informative)

Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive Machinery 98/37/EC, amended by 98/79/EC.

Once this standard is cited in the Official Journal of the European Communities under that Directive and has
been implemented as a national standard in at least one Member State, compliance with the normative
clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity
with the relevant Essential Requirements (except 1.7.4. (f)) of that Directive and associated EFTA regulations.

WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within
the scope of this standard.

4

---------------------- Page: 6 ----------------------

SIST EN ISO 10472-3:2008
EN ISO 10472-3:2008 (E)
Annex ZB
(informative)

Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide a means of conforming to Essential Requirements of the
New Approach Directive Machinery 2006/42/EC.
Once this standard is cited in the Official Journal of the European Communities under that Directive and has
been implemented as a national standard in at least one Member State, compliance with the normative
clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity
with the relevant Essential Requirements (except 1.4.2.1 § 2, 1.7.3, 1.7.4.2 t) and u)) of that Directive and
associated EFTA regulations.
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within
the scope of this standard.



5

---------------------- Page: 7 ----------------------

SIST EN ISO 10472-3:2008

---------------------- Page: 8 ----------------------

SIST EN ISO 10472-3:2008
INTERNATIONAL ISO
STANDARD 10472-3
First edition
1997-12-15
Safety requirements for industrial laundry
machinery —
Part 3:
Washing tunnel lines including component
machines
Exigences de sécurité pour les machines de blanchisserie industrielle —
Partie 3: Trains de lavage incluant les machines composantes
A
Reference number
ISO 10472-3:1997(E)

---------------------- Page: 9 ----------------------

SIST EN ISO 10472-3:2008
ISO 10472-3:1997(E)
Contents
Page
1 Scope . 1
2 Normative references. 1
3 Definitions . 2
4 Hazards . 3
5 Safety requirements and/or measures for the hazards identified in clause 4. 5
5.1 General . 5
5.2 Mechanical hazards. 5
5.2.1 Interface between loading system and continuous tunnel washing machine . 5
Continuous tunnel washing machine. 5
5.2.2
5.2.3 Conveyors between washing machine and squeeze press or centrifugal extraction machine 5
5.2.4 Squeeze press. 5
5.2.5 Centrifugal extraction machine . 6
5.2.6 Transfer conveyor system . 6
5.2.7 Automatic transfer tumbler dryers . 6
5.2.8 Interface between tumbler dryers and unloading system. 7
5.3 Electrical hazards. 7
5.4 Thermal hazards . 7
5.5 Hazards generated by noise .7
5.6 Hazards associated with materials and substances . 7
5.6.1 Fire and explosion . 7
5.6.2 Biological hazards. 7
5.7 Failure of control systems . 8
5.8 Hazards associated with complex installations . 8
6 Verification of safety requirements and/or measures. 8
7 Information concerning machine use. 12
7.1 Instruction handbook . 12
7.2 Warning signs. 12
©  ISO 1997
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet central@iso.ch
X.400 c=ch; a=400net; p=iso; o=isocs; s=central
Printed in Switzerland
ii

---------------------- Page: 10 ----------------------

SIST EN ISO 10472-3:2008
©
ISO ISO 10472-3:1997(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has
been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates
closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical
standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for
voting. Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
International Standard ISO 10472-3 was prepared by Technical Committee ISO/TC 72, Textile machinery and
machinery for dry-cleaning and industrial laundering, Subcommittee SC 5, Industrial laundry and
dry-cleaning machinery.
ISO 10472 consists of the following parts, under the general title Safety requirements for industrial laundry
machinery:
— Part 1: Common requirements
— Part 2: Washing machines and washer-extractors
— Part 3: Washing tunnel lines including component machines
— Part 4: Air dryers
— Part 5: Flatwork ironers, feeders and folders
— Part 6: Ironing and fusing presses
iii

---------------------- Page: 11 ----------------------

SIST EN ISO 10472-3:2008
©
ISO 10472-3:1997(E) ISO
Introduction
This part of ISO 10472 is intended to instruct the designer of industrial laundry machinery in a systematic
manner, focusing on his particular type of machine, regarding the relevant essential safety requirements,
and to suggest possible state-of-the-art safety solutions.
The extent to which hazards are covered is indicated in the scope of this part of ISO 10472. In addition,
machinery should comply as appropriate with ISO/TR 12100-1 and ISO/TR 12100-2 for hazards which are not
specifically referred to in this part of ISO 10472.
All examples given in this part of ISO 10472 represent the state of the art. Equivalent solutions are
acceptable, provided they attain at least the same safety level.
The designer is presumed to have taken into account all the provisions of ISO 10472-1 before considering
this part of ISO 10472.
iv

---------------------- Page: 12 ----------------------

SIST EN ISO 10472-3:2008
©
INTERNATIONAL STANDARD  ISO ISO 10472-3:1997(E)
Safety requirements for industrial laundry machinery —
Part 3:
Washing tunnel lines including component machines
1 Scope
This part of ISO 10472 covers, together with ISO 10472-1, most significant hazards associated with washing
tunnel lines including component machines such as:
— continuous tunnel washing machines;
— squeeze presses or centrifugal extraction machines;
— transfer conveyor systems;
— automatic transfer tumblers;
— loading or unloading system interfaces;
— access platform and ladders.
This part of ISO 10472 does not cover particular hazards for continuous stand-alone washing lines for
endless towels.
This part of ISO 10472 does not cover the hazards caused by processing work which may create an
explosive or flammable atmosphere inside the machine.
This part of ISO 10472 complements the basic requirements laid down in ISO/TR 12100-1 and
ISO/TR 12100-2. It also gives guidance to the designer on assessing the risks associated with the hazards
(see EN 1050) and on selecting measures for attaining the required safety level.
This part of ISO 10472 does not apply to ancillary equipment, e. g. chemical store and supply pumps, steam
valves and supply pipework, vent systems, work feed systems and discharge systems and ducting to the
atmosphere.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of
this part of ISO 10472. At the time of publication, the editions indicated were valid. All standards are subject
to revision, and parties to agreement based on this part of ISO 10472 are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO
maintain registers of currently valid International Standards.
ISO 6182-1:1993, Fire protection — Automatic sprinkler systems — Part 1: Requirements and test methods
for sprinklers.
ISO 10472-1:1997, Safety requirements for industrial laundry machinery — Part 1: Common requirements.
ISO/TR 12100-1:1992, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic
terminology, methodology.
1

---------------------- Page: 13 ----------------------

SIST EN ISO 10472-3:2008
©
ISO 10472-3:1997(E) ISO
ISO/TR 12100-2:1992, Safety of machinery — Basic concepts, general principles for design — Part 2:
Technical principles and specifications.
1)
ISO 13849-1:— , Safety of machinery — Safety-related parts of control systems — Part 1: General principles
for design.
ISO 13852:1996, Safety of machinery — Safety distances to prevent danger zones being reached by the
upper limbs.
1)
ISO 14119:— , Safety of machinery — Interlocking devices associated with guards — Principles for design
and selection.
1)
EN 616:— , Continuous handling equipment and systems — Common safety requirements for design,
manufacturing, erection and commissioning stages.
1)
EN 620:— , Continuous handling equipment and systems — Equipment for mechanical handling both unit
loads and bulk materials — Special safety requirements for design, manufacturing, erection and
commissioning stages.
EN 746-2:1997, Industrial thermoprocessing equipment — Part 2: Safety requirements for combustion and
fuel handling systems.
EN 953:1997, Safety of machinery — General requirements for the design and construction of guards (fixed,
movable).
EN 1037:1995, Safety of machinery — Prevention of unexpected start-up.
EN 1050:1996, Safety of machinery — Risk assessment.
EN 1760-1:1997, Safety of machinery — Pressure sensitive protective devices — Part 1: General principles
for the design and testing of pressure sensing mats and floors.
1)
EN 1760-2:— , Safety of machinery — Pressure sensitive protective devices — Part 2: General principles for
the design and testing of pressure sensitive edges and pressure sensitive bars.
1)
EN 50100-1:— , Safety of machinery — Electro-sensitive protective devices — Part 1:
...