SIST EN 300 394-1 V3.2.1:2012
(Main)Terrestrial Trunked Radio (TETRA) - Conformance testing specification - Part 1: Radio
Terrestrial Trunked Radio (TETRA) - Conformance testing specification - Part 1: Radio
The present document specifies the minimum technical characteristics of TETRA Voice plus Data (V+D) Base Stations (BS) and Mobile Station (MS) equipment, and TETRA Direct Mode Operation (DMO) equipment, and the radio test methods used for type testing. Specific test methods for DMO equipment are defined in annex F of the present document. The purpose of these specifications is to provide a sufficient quality of radio transmission and reception for equipment operating in a TETRA system and to minimize harmful interference to other equipment. The present document is applicable to TETRA systems operating at radio frequencies in the range of 300 MHz to 1 GHz. These specifications do not necessarily include all the characteristics which may be required by a user of equipment, nor do they necessarily represent the optimum performance achievable.
Prizemni snopovni radio (TETRA) - Specifikacija za preskušanje skladnosti - 1. del: Radio
Ta dokument določa minimalne tehnične lastnosti opreme prizemnega snopovnega radia TETRA Voice plus Data (V + D), baznih postaj (BS) in mobilnih postaj (MS), opreme za neposredni način delovanja (DMO) prizemnega snopovnega radia TETRA in metode radijskih preizkusov za homologacijo. Specifične preizkusne metode za opremo DMO so opredeljene v dodatku F tega dokumenta. Namen teh specifikacij je zagotoviti zadostno kakovost radijskega oddajanja in sprejemanja za opremo, ki deluje v sistemu prizemnega snopovnega radia TETRA, in čim bolj zmanjšati škodljive motnje z drugo opremo. Ta dokument velja za sisteme prizemnega snopovnega radia TETRA, ki delujejo na radijskih frekvencah v obsegu od 300 MHz do 1 GHz. Te specifikacije ne vključujejo nujno vseh lastnosti, ki bi jih lahko zahteval uporabnik opreme, niti ne predstavljajo nujno optimalno dosegljivega delovanja.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Prizemni snopovni radio (TETRA) - Specifikacija za preskušanje skladnosti - 1. del: RadioTerrestrial Trunked Radio (TETRA) - Conformance testing specification - Part 1: Radio33.070.10Prizemni snopovni radio (TETRA)Terrestrial Trunked Radio (TETRA)ICS:Ta slovenski standard je istoveten z:EN 300 394-1 Version 3.2.1SIST EN 300 394-1 V3.2.1:2012en01-december-2012SIST EN 300 394-1 V3.2.1:2012SLOVENSKI
STANDARD
SIST EN 300 394-1 V3.2.1:2012
ETSI EN 300 394-1 V3.2.1 (2012-10) Terrestrial Trunked Radio (TETRA); Conformance testing specification; Part 1: Radio
European Standard SIST EN 300 394-1 V3.2.1:2012
ETSI ETSI EN 300 394-1 V3.2.1 (2012-10)2
Reference REN/TETRA-03201 Keywords DMO, testing, TETRA, V+D ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2012. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 394-1 V3.2.1:2012
ETSI ETSI EN 300 394-1 V3.2.1 (2012-10)3 Contents Intellectual Property Rights . 10 Foreword . 10 Introduction . 10 1 Scope . 11 2 References . 11 2.1 Normative references . 11 2.2 Informative references . 12 3 Definitions, symbols and abbreviations . 12 3.1 Definitions . 12 3.2 Symbols . 12 3.3 Abbreviations . 13 4 General . 13 4.1 Presentation of equipment for testing purposes . 13 4.1.1 Facilities and information required for testing . 14 4.1.2 Choice of radio frequency channels to be tested . 14 4.1.3 Interpretation of the measurement results . 15 4.2 Mechanical and electrical design . 15 4.2.1 General . 15 4.2.2 Controls . 15 4.2.3 Marking . 15 5 Radio test configuration, test signals and test modes . 15 5.1 General functional radio test configuration . 16 5.2 Radio test modes . 16 5.2.1 Test receive mode . 16 5.2.1.1 MS test receive mode for phase modulation . 17 5.2.1.2 BS test receive mode for phase modulation . 17 5.2.1.3 MS test receive mode for QAM (where supported) . 18 5.2.1.4 BS test receive mode for QAM (where supported) . 18 5.2.2 Test transmit mode. 19 5.2.2.1 MS testing for phase modulation . 19 5.2.2.2 Void. 19 5.2.2.3 BS testing for phase modulation . 19 5.2.2.4 MS testing for QAM (where supported) . 20 5.2.2.5 BS testing for QAM (where supported) . 20 5.3 Radio test signals . 21 5.3.1 General . 21 5.3.2 Test signal T1 (TETRA wanted signal, phase modulation) . 21 5.3.2.1 MS testing . 21 5.3.2.2 BS testing . 22 5.3.2.3 Void. 23 5.3.2.4 Void. 23 5.3.3 Test signal T2 (TETRA interferer) . 23 5.3.4 Test signal T3 (unmodulated interferer) . 23 5.3.5 Test signal T4 (TETRA wanted signal, QAM) . 23 5.3.5.1 MS testing . 23 5.3.5.1.1 Use of synchronization burst in frame 18 when testing CA MSs . 25 5.3.5.1.1a Use of frequency correction burst in frame 18 when testing DA MSs . 27 5.3.5.2 BS testing . 28 6 Test conditions . 29 6.1 General . 29 6.2 Power sources and ambient conditions . 29 6.2.1 Normal test conditions . 29 SIST EN 300 394-1 V3.2.1:2012
ETSI ETSI EN 300 394-1 V3.2.1 (2012-10)4 6.2.2 Extreme test conditions . 30 6.3 Procedure for tests at extreme temperatures . 31 6.3.1 Equipment designed for continuous operation . 31 6.3.2 Equipment designed for intermittent operation. 31 7 Technical characteristics . 31 7.1 Transmitter parameter definitions and limits . 31 7.1.1 Transmitter output power . 31 7.1.1.1 Definition . 31 7.1.1.2 Limit values for phase modulation and QAM . 32 7.1.2 Unwanted output power in non-active transmit state . 32 7.1.2.1 Definition . 32 7.1.2.2 Limit values. 32 7.1.3 Adjacent channel power due to modulation . 32 7.1.3.1 Definition . 32 7.1.3.2 Limit values for phase modulation . 32 7.1.3.3 Limit values for QAM . 33 7.1.4 Adjacent channel power due to switching transients . 34 7.1.4.1 Definition . 34 7.1.4.2 Limit values for phase modulation . 34 7.1.4.3 Limit values for QAM . 34 7.1.5 Unwanted emissions far from the carrier . 35 7.1.5.1 Definition . 35 7.1.5.2 Limit values for phase modulation . 35 7.1.5.3 Limit values for QAM . 36 7.1.6 Unwanted radiated emissions . 37 7.1.6.1 Definition . 37 7.1.6.2 Limit values. 37 7.1.7 Unwanted emissions during the BLCH/CLCH (linearization) . 37 7.1.7.1 Definition . 37 7.1.7.2 Limit values for phase modulation . 37 7.1.7.3 Limit values for QAM . 37 7.1.8 Transmitter intermodulation attenuation . 38 7.1.8.1 Definition . 38 7.1.8.2 Limit values for phase modulation and QAM . 38 7.1.8.2.1 MS Limit values . 38 7.1.8.2.2 Limit values for single BS transmitter . 38 7.1.8.2.3 Limit values for intra BS intermodulation . 38 7.2 Receiver parameter definitions and limits . 39 7.2.1 General . 39 7.2.2 Nominal error rates . 39 7.2.2.1 Definition . 39 7.2.2.2 Limit values for phase modulation . 39 7.2.2.3 Limit values for QAM . 39 7.2.3 Reference sensitivity performance . 39 7.2.3.1 Definition . 39 7.2.3.2 Limit values for phase modulation . 40 7.2.3.3 Limit values for QAM . 40 7.2.4 Reference interference performance . 42 7.2.4.1 Definition . 42 7.2.4.2 Limit values for phase modulation . 42 7.2.4.3 Limit values for QAM . 43 7.2.4.3.1 Adjacent channel interference . 43 7.2.4.3.2 Co-channel interference . 43 7.2.5 Blocking characteristics . 44 7.2.5.1 Definition . 44 7.2.5.2 Limit values for phase modulation . 44 7.2.5.3 Limit values for QAM . 44 7.2.6 Spurious response rejection . 45 7.2.6.1 Definition . 45 7.2.6.2 Limit values for phase modulation . 45 7.2.6.3 Limit values for QAM . 45 SIST EN 300 394-1 V3.2.1:2012
ETSI ETSI EN 300 394-1 V3.2.1 (2012-10)5 7.2.7 Intermodulation response rejection . 46 7.2.7.1 Definition . 46 7.2.7.2 Limit values. 46 7.2.8 Unwanted conducted emissions . 47 7.2.8.1 Definition . 47 7.2.8.2 Limit values. 47 7.2.9 Unwanted radiated emissions . 47 7.2.9.1 Definition . 47 7.2.9.2 Limit values. 47 7.3 Transmitter/receiver parameter definitions and limits . 47 7.3.1 Modulation accuracy. 47 7.3.1.1 Definition . 47 7.3.1.2 Limit values for phase modulation . 47 7.3.1.3 Limit values for QAM . 47 7.3.2 Carrier frequency accuracy . 48 7.3.2.1 Definition . 48 7.3.2.2 Limit values. 48 7.3.3 MS receiver performance for synchronization burst acquisition . 48 7.3.3.1 Definition for phase modulation . 48 7.3.3.2 Limit values for phase modulation . 48 7.3.3.3 Definition for QAM modulation . 48 7.3.3.4 Limit values for QAM modulation . 48 7.3.4 MS Frame alignment performance . 49 7.3.4.1 Definition . 49 7.3.4.2 Limit values. 49 7.3.5 MS link control . 49 7.3.5.1 Definition . 49 7.3.5.2 Limit values. 49 8 Methods of measurement for transmitter parameters . 50 8.1 Transmitter output power . 50 8.1.1 Transmitter output power for phase modulation . 50 8.1.1.1 MS transmitter output power for phase modulation . 50 8.1.1.2 BS transmitter output power for phase modulation . 51 8.1.2 Transmitter output power for QAM . 52 8.1.2.1 MS transmitter output power for QAM . 52 8.1.2.2 BS transmitter output power for QAM. 53 8.2 Unwanted output power in non active transmit state . 53 8.3 Adjacent channel power due to modulation . 53 8.4 Adjacent channel power due to switching transients . 54 8.5 Unwanted emissions far from the carrier . 54 8.6 Unwanted radiated emissions . 56 8.7 Unwanted emissions during the BLCH/CLCH and BLCH-Q/CLCH-Q (linearization) . 56 8.7.1 MS unwanted emissions during the CLCH (linearization) . 56 8.7.2 BS unwanted emissions during the BLCH (linearization) . 57 8.7.3 MS unwanted emissions during the CLCH-Q (linearization) . 57 8.7.4 BS unwanted emissions during the BLCH-Q (linearization) . 57 8.8 Transmitter intermodulation attenuation . 58 8.8.1 MS Transmitter intermodulation attenuation . 58 8.8.2 BS Transmitter intermodulation attenuation . 58 8.8.3 Intra BS transmitter intermodulation attenuation . 58 9 Methods of measurement for receiver parameters . 59 9.1 General . 59 9.2 Nominal error rates for phase modulation . 59 9.2.1 MS nominal error rate . 59 9.2.2 BS nominal error rate . 59 9.3 Reference sensitivity performance . 59 9.3.1 MS reference sensitivity performance for phase modulation . 59 9.3.2 BS reference sensitivity performance for phase modulation . 60 9.3.3 MS reference sensitivity performance for QAM . 60 9.3.4 BS reference sensitivity performance for QAM . 60 SIST EN 300 394-1 V3.2.1:2012
ETSI ETSI EN 300 394-1 V3.2.1 (2012-10)6 9.3.5 PUEM performance . 60 9.4 Reference interference performance . 61 9.4.1 MS reference interference performance for phase modulation . 61 9.4.2 BS reference interference perfo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.