SIST EN ISO 9333:2023

SLOVENSKI STANDARD
01-januar-2023
Nadomešča:
SIST EN ISO 9333:2006
Zobozdravstvo - Materiali za spajkanje (ISO 9333:2022)
Dentistry - Brazing materials (ISO 9333:2022)
Zahnheilkunde - Hartlote (ISO 9333:2022)
Médecine bucco-dentaire - Produits pour brasage (ISO 9333:2022)
Ta slovenski standard je istoveten z: EN ISO 9333:2022
ICS:
11.060.10 Zobotehnični materiali Dental materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 9333
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2022
EUROPÄISCHE NORM
ICS 11.060.10 Supersedes EN ISO 9333:2006
English Version
Dentistry - Brazing materials (ISO 9333:2022)
Médecine bucco-dentaire - Produits pour brasage (ISO Zahnheilkunde - Hartlote (ISO 9333:2022)
9333:2022)
This European Standard was approved by CEN on 3 September 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9333:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 9333:2022) has been prepared by Technical Committee ISO/TC 106 "Dentistry"
in collaboration with Technical Committee CEN/TC 55 “Dentistry” the secretariat of which is held by
DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2023, and conflicting national standards shall be
withdrawn at the latest by April 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 9333:2006.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 9333:2022 has been approved by CEN as EN ISO 9333:2022 without any modification.

INTERNATIONAL ISO
STANDARD 9333
Third edition
2022-08
Dentistry — Brazing materials
Médecine bucco-dentaire — Produits pour brasage
Reference number
ISO 9333:2022(E)
ISO 9333:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 9333:2022(E)
Contents Page
Foreword .v
1 S c op e . 1
2 Nor m at i ve r ef er enc e s . 1
3 Terms and definitions . 1
4 R e qu i r ement s . 2
4.1 Chemical composition . 2
4.1.1 Metallic materials to be joined . 2
4.1.2 R eported composition . 2
4.1.3 Permitted deviation from the reported composition . 2
4.1.4 Hazardous elements . 2
4.2 Biocompatibility . 2
4.3 M echanical tensile strength of brazed joints . 2
4.4 C orrosion resistance . 3
4.4.1 S tatic immersion test . 3
4.4.2 A ppearance after corrosion exposure . 3
4.5 M elting range . 3
5 S a mpl i n g . 3
6 P reparation of specimens .3
6.1 General . 3
6.1.1 Test specimen . 3
6.1.2 C asting . 3
6.1.3 Other methods . 4
6.1.4 Treatment of specimens . . 4
6.2 Sp ecimens for corrosion testing . 4
6.2.1 G eneral . 4
6.2.2 P rocedure . 4
6.3 S pecimens for tensile testing . 4
6.3.1 G eneral . 4
6.3.2 Procedure . 4
6.3.3 Additional testing . 5
7 M easurement and test methods .6
7.1 Vi sual inspection . 6
7.1.1 S pecimens . 6
7.1.2 I nstruction for use, packaging and labelling . 6
7.2 Chemical composition . 6
7.3 T ensile testing . 6
7.3.1 Apparatus . 6
7.3.2 Test procedure. 6
7.3.3 Evaluation of the tensile test results . 7
7.4 Corrosion resistance . 7
7.4.1 G eneral . 7
7.4.2 Analysis . 7
7.4.3 Microscopic inspection . 7
7.4.4 C orrosion test report . 7
7.5 M elting range . 8
8 Te s t r ep or t . 8
9 I nstruction for use .8
10 M arking and labelling . 9
10.1 M arking . 9
10.2 Labelling . 9
10.3 Packaging . 9
iii
ISO 9333:2022(E)
Bibliography .10
iv
ISO 9333:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommittee SC 2,
Prosthodontic materials, in collaboration with the European Committee for Standardization (CEN)
Technical Committee CEN/TC 55, Dentistry, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 9333:2006), which has been technically
revised.
The main changes are as follows:
— the brazing materials with silver as the main component have been excluded from the scope;
— the definitions in Clause 3 have been clarified and harmonized with ISO 22674;
— the corrosion requirements in 4.4 have been harmonized with ISO 22674 and ISO 10271;
— the analysis of corrosion elements has been added as a requirement in 7.4.2;
— the melting range requirements (7.5) have been harmonized with ISO 22674;
— a requirement for a test report has been added as a new Clause 8;
— the IFU requirement for a working temperature has been added in Clause 9;
— the labelling requirement for marking of working temperature has been added in Clause 10 as
optional.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
v
INTERNATIONAL STANDARD ISO 9333:2022(E)
Dentistry — Brazing materials
1 S cope
This document specifies the requirements and test methods for dental brazing
...