SIST EN ISO 3219-2:2021

SLOVENSKI STANDARD
SIST EN ISO 3219-2:2021
01-julij-2021
Nadomešča:
SIST EN ISO 3219:1997
Reologija - 2. del: Splošna načela za rotacijsko in oscilacijsko reometrijo (ISO 3219
-2:2021)
Rheology - Part 2: General principles of rotational and oscillatory rheometry (ISO 3219-
2:2021)
Rheologie - Teil 2: Allgemeine Grundlagen der Rotations- und Oszillationsrheometrie
(ISO 3219-2:2021)
Rhéologie - Partie 2: Principes généraux de la rhéométrie rotative et oscillatoire (ISO
3219-2:2021)
Ta slovenski standard je istoveten z: EN ISO 3219-2:2021
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 3219-2:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 3219-2:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 3219-2:2021


EN ISO 3219-2
EUROPEAN STANDARD

NORME EUROPÉENNE

May 2021
EUROPÄISCHE NORM
ICS 83.080.01 Supersedes EN ISO 3219:1994
English Version

Rheology - Part 2: General principles of rotational and
oscillatory rheometry (ISO 3219-2:2021)
Rhéologie - Partie 2: Principes généraux de la Rheologie - Teil 2: Allgemeine Grundlagen der
rhéométrie rotative et oscillatoire (ISO 3219-2:2021) Rotations- und Oszillationsrheometrie (ISO 3219-
2:2021)
This European Standard was approved by CEN on 9 March 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3219-2:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 3219-2:2021
EN ISO 3219-2:2021 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 3219-2:2021
EN ISO 3219-2:2021 (E)
European foreword
This document (EN ISO 3219-2:2021) has been prepared by Technical Committee ISO/TC 35 "Paints
and varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2021, and conflicting national standards
shall be withdrawn at the latest by November 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3219:1994.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 3219-2:2021 has been approved by CEN as EN ISO 3219-2:2021 without any
modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 3219-2:2021

---------------------- Page: 6 ----------------------
SIST EN ISO 3219-2:2021
INTERNATIONAL ISO
STANDARD 3219-2
First edition
2021-05
Rheology —
Part 2:
General principles of rotational and
oscillatory rheometry
Rhéologie —
Partie 2: Principes généraux de la rhéométrie rotative et oscillatoire
Reference number
ISO 3219-2:2021(E)
©
ISO 2021

---------------------- Page: 7 ----------------------
SIST EN ISO 3219-2:2021
ISO 3219-2:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

---------------------- Page: 8 ----------------------
SIST EN ISO 3219-2:2021
ISO 3219-2:2021(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 3
5 Measuring principles . 4
5.1 General . 4
5.2 Rotational rheometry . 5
5.3 Oscillatory rheometry . 6
6 Measuring assembly . 8
6.1 General . 8
6.2 Temperature control systems . 9
6.3 Measuring geometries . 9
6.3.1 General. 9
6.3.2 Absolute measuring geometries .10
6.3.3 Relative measuring geometries .20
6.4 Selected optional accessories .24
6.4.1 Cover with or without solvent trap .24
6.4.2 Passive and active thermal covers .25
6.4.3 Stepped plates .26
Annex A (informative) Information on rheometry and flow field patterns .27
Bibliography .45
© ISO 2021 – All rights reserved iii

---------------------- Page: 9 ----------------------
SIST EN ISO 3219-2:2021
ISO 3219-2:2021(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www .iso .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and varnishes, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 139, Paints and varnishes, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement), and in cooperation
with ISO/TC 61, Plastics, SC 5, Physical-chemical properties.
This document cancels and replaces ISO 3219:1993, which have been technically revised. The main
changes compared to the previous editions are as follows:
— plate-plate measuring geometry has been added;
— relative measuring geometries have been added;
— oscillatory rheometry has been added.
A list of all parts in the ISO 3219 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved

---------------------- Page: 10 ----------------------
SIST EN ISO 3219-2:2021
INTERNATIONAL STANDARD ISO 3219-2:2021(E)
Rheology —
Part 2:
General principles of rotational and oscillatory rheometry
1 Scope
This document specifies the general principles of rotational and oscillatory rheometry.
Detailed information is presented in Annex A. Further background information is covered in subsequent
parts of the ISO 3219 series, which are currently in preparation.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 3219-1, Rheology — Part 1: General terms and definitions for rotational and oscillatory rheometry
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 3219-1 and the following
apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
3.1
measuring gap
space between the boundary surfaces of the measuring geometry
3.2
gap width
h
H
cc
H
cp
distance between the boundary surfaces of the measuring geometry
Note 1 to entry: The symbol h refers to a gap width that can be varied (e.g. plate-plate measuring geometry); the
symbol H refers to a gap width which is not variable and which is defined by the relevant measuring geometry.
H is the gap width of the coaxial-cylinders geometry. H is the gap width of the cone-plate geometry.
cc cp
Note 2 to entry: The distance between the boundary surfaces is given by the difference in the radii (coaxial
cylinders), the cone angle (cone-plate) or the distance between the two plates.
Note 3 to entry: In cone-plate measuring geometries, the gap width varies as a function of the radius across the
measuring geometry. The value H is the distance between the flattened cone tip and the plate.
cp
© ISO 2021 – All rights reserved 1

---------------------- Page: 11 ----------------------
SIST EN ISO 3219-2:2021
ISO 3219-2:2021(E)

3.3
flow field coefficient
geometric factor
k
quotient of the shear stress factor (3.9) k and the strain factor (3.8) k
τ γ
Note 1 to entry: The flow field coefficient k relates the angular velocity Ω and torque M to the shear viscosity η of
the fluid as given by the following formula:
M
    η=⋅k
Ω
−3
The flow field coefficient k is expressed in radians per cubic metre (rad·m ). It can be calculated from the shape
and dimensions of an absolute measuring geometry (3.7).
3.4
no-slip condition
presence of a relative velocity of zero between a boundary surface and the immediately adjacent fluid
layer
3.5
wall slip
presence of a non-zero relative velocity between a boundary surface and the immediately adjacent fluid
layer
3.6
relative measuring geometry
measuring geometry for which the flow profile and thus the rheological parameters cannot be
calculated
Note 1 to entry: For relative measuring geometries, the viscosity shall not be given in pascal multiplied by
seconds (Pa⋅s) except in the case of plate-plate measuring geometries if the correction referred to in 6.3.3.1.2 is
used.
3.7
absolute measuring geometry
measuring geometry for which the flow profile and thus the rheological parameters can be calculated
exactly for the entire sample, regardless of its flow properties
3.8
strain factor
k
γ
proportionality factor between the angular deflection φ and shear strain γ for absolute measuring
geometries (3.7)
Note 1 to entry: The absolute value of the strain factor corresponds to the absolute value of the shear rate factor.

The latter is the proportionality factor between the shear rate γ and the angular velocity Ω.
Note 2 to entry: This factor is called the shear rate factor in the rotation test and the strain factor in the oscillatory
test.
−1
Note 3 to entry: The strain factor k has units of reciprocal radians (rad ).
γ
3.9
shear stress factor
k
τ
proportionality factor between the torque M and the shear stress τ for absolute measuring geometries
(3.7)
−3
Note 1 to entry: The shear stress factor k has units of reciprocal cubic metres (m ).
τ
2 © ISO 2021 – All rights reserved

---------------------- Page: 12 ----------------------
SIST EN ISO 3219-2:2021
ISO 3219-2:2021(E)

4 Symbols
Table 1 — Symbols and units
Meaning Symbol Unit
*
Absolute value of the complex shear modulus Pa
G
Absolute value of the complex viscosity * Pa·s
η
−2
ϕ
Acceleration of the angular deflection rad·s
Amplitude of the angular deflection of the motor * rad
ϕ
M,0
*
Amplitude of angular deflection of torque transducer rad
ϕ
D,0
Amplitude of the angular deflection rad
ϕ
0
−1
Amplitude of the angular velocity ϕ rad·s
0
−1
Amplitude of the shear rate  s
γ
0
Amplitude of the shear strain γ 1
0
Amplitude of the shear stress τ Pa
0
Amplitude of the torque M N·m
0
−2
*
Angular acceleration of motor rad·s
ϕ
M
−2
*
Angular acceleration of torque transducer rad·s

ϕ
D
Angular deflection φ rad
*
Angular deflection of motor rad
ϕ
M
Angular deflection of sample * rad
ϕ
P
*
Angular deflection of torque transducer rad
ϕ
D
−1 −1
Angular frequency ω rad·s or s
−1
Angular velocity across the measuring gap ω(r) rad·s
−1
Angular velocity (presented in brackets: as the time derivative of the angular Ω,  ϕ rad·s
()
deflection)
−1
*
Angular velocity of motor rad·s
ϕ
M
−1
Angular velocity of torque transducer * rad·s

ϕ
D
Coefficient of bearing friction D N·m·s
L
Coefficient of friction D N·m·s
*
Complex angular deflection rad
ϕ
*
Complex shear modulus Pa
G
Complex torque * N·m
M
*
Complex viscosity Pa·s
η
Cone angle α ° or rad
Deflection path s m
tanζ
Drive loss factor 1
Drive phase angle ζ rad
Face factor c 1
L
−3
Flow field coefficient, geometric factor k rad·m
Frequency f Hz
NOTE The parameters marked with an * refer to complex-valued parameters whose real part is denoted by ′ and
imaginary part by ′′.
© ISO 2021 – All rights reserved 3

---------------------- Page: 13 ----------------------
SIST EN ISO 3219-2:2021
ISO 3219-2:2021(E)

Table 1 (continued)
Meaning Symbol Unit
Gap width h m
Gap width defined by the coaxial cylinders geometry H m
cc
Gap width defined by the cone-plate geometry H m
cp
−1
Geometry compliance C rad·(N·m)
G
Imaginary part of the complex viscosity η′′ Pa·s
Imaginary unit i 1
Loss angle, phase angle δ rad
Loss factor tanδ 1
2
Moment of inertia I N·m·s
Real part of the complex viscosity η′ Pa·s
−1 −1
Rotational speed n s or min
Sample torque * N·m
M
P
Shear force F N
Shear loss modulus, viscous shear modulus G′′ Pa
Shear modulus G Pa
2
Shear plane A m
−1
Shear rate factor rad
k

γ
−1

Shear rate, shear deformation rate γ s
Shear storage modulus, elastic shear modulus G′ Pa
Shear strain, shear deformation γ 1 or %
Shear stress τ Pa
−3
Shear stress factor m
k
τ
Shear viscosity η Pa·s
−1
Strain factor k rad
γ
Temperature T °C or K
Time t s
Torque M N·m
*
Torque applied by motor N·m
M
M
*
Torque caused by bearing friction N·m
M
L
*
Torque caused by transducer inertia N·m
M
I
*
Torque measured by transducer N·m
M
m
−1
Torsional compliance of the measurement system C rad·(N·m)
−1
Velocity v m·s
NOTE The parameters marked with an * refer to complex-valued parameters whose real part is denoted by ′ and
imaginary part by ′′.
5 Measuring principles
5.1 General
There are rotational tests, oscillatory tests and various step tests. The different tests can be combined
with one another.
4 © ISO 2021 – All rights reserved

---------------------- Page: 14 ----------------------
SIST EN ISO 3219-2:2021
ISO 3219-2:2021(E)

These can be carried out using various measuring types: controlled deformation (CD), controlled rate
(CR) or controlled stress (CS).
5.2 Rotational rheometry
In the basic rotational test, the sample is subjected to constant or variable loading in one direction.
The shear viscosity η is calculated from the measured data. The corresponding mechanical input
and response parameters are listed in Tables A.1 and A.3. The basic parameters of the test can be
represented schematically in terms of the two-plates model. An infinitesimal element of the measuring
geometry is considered in this subclause (see Figure 1). The two-plates model consists of two parallel
plates, each with a surface area A and with a gap width h, between which the sample is located. The
velocity of the lower plate is zero (v = 0). The upper plate is moved by a defined shear force F, which
results in a velocity v. It is assumed that the sample between the plates consists of layers that move at
different velocities of between v = 0 and v.
Key
1 sample
v velocity
A shear plane
h gap width
F shear force
Figure 1 — Two-plate model with a simplified schematic representation of the basic parameters
of a rotational test
With this model, the following parameters are calculated using Formulae (1) to (3):
F
τ = (1)
A
where
τ is the shear stress, in pascals;
F is the shear force, in newtons;
A is the shear plane, in square metres.
v

γ = (2)
h
where

γ
is the shear rate, in reciprocal seconds;
v is the velocity, in metres per second;
h is the gap width, in metres.
© ISO 2021 – All rights reserved 5

---------------------- Page: 15 ----------------------
SIST EN ISO 3219-2:2021
ISO 3219-2:2021(E)

Based on the Newtonian law of viscosity, the shear viscosity can be calculated using Formula (3):
τ
η= (3)

γ
where η is the shear viscosity, in pascal multiplied by seconds.
5.3 Oscillatory rheometry
In the basic oscillatory test, the sample is stimulated with an angular deflection or torque amplitude at
a given oscillation frequency. The resulting response oscillates with the same frequency and is
characterized by an amplitude and phase shift. The corresponding mechanical input and response
parameters are listed in Tables A.2 and A.3. Parameters such as the shear storage modulus G′ (elastic
shear modulus), the shear loss modulus G′′ (viscous shear modulus), the absolute value of the complex
*
viscosity η and the loss factor tan δ can be calculated from the measured data in order to characterize
the viscoelastic behaviour. The mathematical principles are presented in A.3. The basic parameter of
the test can be represented schematically in terms of the two-plates model (see Figure 2).
Key
1 sample
s deflection path
φ deflection angle
A shear plane
h gap width
F shear force
Figure 2 — Two-plate model with a simplified schematic representation of the basic parameters
of an oscillatory test
With this model, the following parameters can be calculated using Formula (4):
s
γ = (4)
h
where
γ is the shear strain, dimensionless;
s is the deflection path, in metres;
h is the gap width, in metres.
6 © ISO 2021 – All rights reserved

---------------------- Page: 16 ----------------------
SIST EN ISO 3219-2:2021
ISO 3219-2:2021(E)

In the oscillatory test, the shear strain γ varies sinusoidally as a function of time t, see Figure 3. The
associated shear stress τ is shifted within the viscoelastic range by the loss angle δ at the same angular
frequency ω. Formulae (5) and (6) apply:
γγ()tt= sin()ω (5)
0
where
γ is the amplitude of the shear strain, dimensionless;
0
ω is the angular frequency, in radians per second;
t is the time, in seconds.
ττtt=+sin ωδ (6)
() ()
0
where
τ is the amplitude of the shear stress, in pascals;
0
δ is the loss angle, in radians.
Key
γ shear strain
τ shear stress
ω angular frequency
t time
δ loss angle
Figure 3 — Schematic representation of the shear strain and shear stress functions for an
oscillatory test
NOTE Degrees (°) are commonly used in practice as the unit for the loss angle δ. The following conversion
applies: 2π rad = 360°.
In the case of ideal elastic behaviour (in accordance with Hooke’s law), the loss angle has a value
of δ = 0°, i.e. the shear strain and shear stress are always in phase. In the case of ideal viscous behaviour
(in accordance with Newton’s law), the loss angle has a value of δ = π/2 = 90°, i.e. the shear stress curve
is 90° ahead of the shear strain curve.
© ISO 2021 – All rights reserved 7

---------------------- Page: 17 ----------------------
SIST EN ISO 3219-2:2021
ISO 3219-2:2021(E)

*
Using Hooke’s elasticity law, the complex shear modulus G* and its absolute value G can be calculated
using Formulae (7) and (8):
τ t
()
*
G = (7)
γ ()t
* 22
GG=+′″G (8)
where
G* is the complex shear modulus, in pascals;
G′ is the shear storage modulus, in pascals;
G′′ is the shear loss modulus, in pascals;
G* describes the overall viscoelastic behaviour.
This can be separated into an elastic component G′ (shear storage modulus) and a viscous component G′′
(shear loss modulus) using Formulae (9) and (10).
τ
0
′
G = cosδ (9)
γ
0
τ
0
G″= sinδ (10)
γ
0
The quotient of the shear loss modulus G′′ and shear storage modulus G′ is the dimensionless loss
factor tanδ, see Formula (11):
G″
tanδ = (11)
G′
The ratio of the absolute value of the complex shear modulus G* and the angular frequency ω is the
absolute value of the complex viscosity η*, see Formula (12):
*
G
*
η = (12)
ω
*
where η is the absolute value of the complex viscosity, in pascal multiplied by seconds.
6 Measuring assembly
6.1 General
The rheological properties are investigated using a measuring system consisting of a measuring device
(viscometer or rheometer) and a measuring geometry (e.g. cone-plate).
The viscometer can only measure the viscosity in rotation (viscometry). This means that the viscosity
function of the sample can be determined as a function of the parameters of time, temperature, shear
rate, shear stress and others such as pressure.
With a rheometer, it is possible to carry out all basic tests in rotation and oscillation (rheometry).
Alongside the viscosity function, the viscoelastic properties can be determined, e.g. shear storage
modulus and shear loss modulus.
8 © ISO 2021 – All rights reserved

---------------------- Page: 18 ----------------------
SIST EN ISO 3219-2:2021
ISO 3219-2:2021(E)

A measuring assembly, consisting of a measuring device, a measuring geometry and optional
accessories, is shown in Figure 4. The measuring device and individual components, such as the
temperature control system, can be computer-controlled.
Figure 4 — Example of a measuring assembly
The sample to be investigated is located in a measuring gap where a defined flow profile is generated
in the sample. A necessary prerequisite for this is a sufficiently small gap width. When viscometers
or rheometers are used, they shall be able to impose or detect torque or rotational speed/angular
deflection. The imposed parameter shall be adjustable both in time-dependent and time-independent
manners.
For viscometric measurements, all viscometers are principally suitable, regardless of how the drive
and/or detection unit are supported. For measurements in oscillation, rheometers shall be used that
have the lowest possible internal friction in the drive or detection unit.
To cover the broadest possible range of applications, the viscometer or rheometer shall be able to work
with different measuring geometries. The range of the torques or angular deflections, that result and
the measuring range that can be achieved, depend on the measuring system. The type of measuring
device and measuring geometry to be selected depends on the sample.
6.2 Temperature control systems
A temperature control system consists of one or more temperature control components for heating and/
or cooling, including the required media (e.g. air, water, liquid nitrogen) and the necessary connections
(e.g. hoses and insulation for these hoses).
The rheological properties of the sample are temperature-dependent. As a result, measures such as
controlling of the sample temperature and its measurement with one or more temperature sensors in
the immediate vicinity of the sample are required.
The temperature of the sample shall be kept constant as a function of time during the measurement
period.
6.3 Measuring geometries
6.3.1 General
A measuring geometry consists of two parts that form a sample chamber where the sample is located. A
measuring geometry consists of a rotor and a stator or of two rotors.
© ISO 2021 – All rights reserved 9

---------------------- Page: 19 ----------------------
SIST EN ISO 3219-2:2021
ISO 3219-2:2021(E)

The meas
...