oSIST prEN ISO 14439:2007

SLOVENSKI STANDARD
oSIST prEN ISO 14439:2007
01-november-2007
Steklo v gradbeništvu - Pravila za zastekljevanje - Zagozdna zasteklitev (ISO/DIS
14439:2007)
Glass in building - Assembly rules - Glazing wedges (ISO/DIS 14439:2007)
Verre dans la construction - Regles de pose - Calage des vitrages (ISO/DIS 14439:2007)
Ta slovenski standard je istoveten z: prEN ISO 14439
ICS:
81.040.20 Steklo v gradbeništvu Glass in building
oSIST prEN ISO 14439:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
prEN ISO 14439
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2007
ICS 81.040.20

English Version
Glass in building - Assembly rules - Glazing wedges (ISO/DIS
14439:2007)
Verre dans la construction - Règles de pose - Calage des
vitrages (ISO/DIS 14439:2007)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
CEN/TC 129.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 14439:2007: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------
prEN ISO 14439:2007 (E)
Contents Page
Foreword.3

2

---------------------- Page: 3 ----------------------
prEN ISO 14439:2007 (E)
Foreword
This document (prEN ISO 14439:2007) has been prepared by Technical Committee CEN/TC 129 "Glass in
building", the secretariat of which is held by NBN, in collaboration with Technical Committee ISO/TC 160
"Glass in building".
This document is currently submitted to the parallel Enquiry.
3

---------------------- Page: 4 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 14439
ISO/TC 160/SC 2 Secretariat: ANSI
Voting begins on: Voting terminates on:
2007-08-16 2008-01-16
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Glass in building — Assembly rules — Glazing wedges
Verre dans la construction — Règles de pose — Calage des vitrages
ICS 81.040.20

ISO/CEN PARALLEL ENQUIRY
This draft International Standard is a draft standard developed within the European Committee for
Standardization (CEN) and processed under the CEN-lead mode of collaboration as defined in the
Vienna Agreement. The document has been transmitted by CEN to ISO for circulation for ISO member
body voting in parallel with CEN enquiry. Comments received from ISO member bodies, including those
from non-CEN members, will be considered by the appropriate CEN technical body. Should this DIS be
accepted, a final draft, established on the basis of comments received, will be submitted to a parallel two-
month FDIS vote in ISO and formal vote in CEN.
In accordance with the provisions of Council Resolution 15/1993 this document is circulated in
the English language only.
Conformément aux dispositions de la Résolution du Conseil 15/1993, ce document est distribué
en version anglaise seulement.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
©
International Organization for Standardization, 2007

---------------------- Page: 5 ----------------------
ISO/DIS 14439
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying,
recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
©
ii ISO 2007 – All rights reserved

---------------------- Page: 6 ----------------------
prEN ISO 14439:2007 (E)
Contents Page
Foreword. 4
Introduction . 5
1 Scope. 5
2 Normative references. 5
3 Definition . 5
4 Requirements for glazing blocks . 6
4.1 General . 6
4.2 Setting blocks. 6
4.2.1 Function . 6
4.2.2 Positioning. 6
4.2.3 Material . 6
4.2.4 Dimensions. 7
4.3 Location blocks . 8
4.3.1 Function . 8
4.3.2 Positioning. 8
4.3.3 Material . 8
4.3.4 Dimensions. 8
4.4 Distance pieces. 8
4.4.1 Function . 8
4.4.2 Material . 8
4.4.3 Positioning. 9
4.4.4 Dimensions. 9
Annex A (normative) Positioning of glazing blocks as a function of frame type . 10
Annex B (informative) Examples of setting blocks . 17
Annex C (informative) Practical recommendations on the required length of a setting block . 19

3

---------------------- Page: 7 ----------------------
prEN ISO 14439:2007 (E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 14439 was prepared by Technical Committee ISO/TC 160, Glass in building, Subcommittee SC 2, and
by Technical Committee CEN/TC 129, Glass in building in collaboration.
This second/third/. edition cancels and replaces the first/second/. edition (), [clause(s) / subclause(s) /
table(s) / figure(s) / annex(es)] of which [has / have] been technically revised.

4

---------------------- Page: 8 ----------------------
prEN ISO 14439:2007 (E)
Introduction
The properties and functions of blocks, described and illustrated in the following clauses,
...