SIST EN 14307:2016
(Main)Thermal insulation products for building equipment and industrial installations - Factory made extruded polystyrene foam (XPS) products - Specification
Thermal insulation products for building equipment and industrial installations - Factory made extruded polystyrene foam (XPS) products - Specification
This European Standard specifies the requirements for factory made extruded polystyrene foam products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately - 180 °C to + 75 °C.
Below an operating temperature of - 50 °C, special tests regarding the suitability of the material in the intended application are advised (e.g. liquefaction of oxygen). Manufacturer's advice should be heeded in all cases.
The products are manufactured in the form of faced or unfaced boards, pipe sections, segments and prefabricated ware.
This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.
Products covered by this standard are also used in prefabricated thermal insulating systems and composite panels; the performance of systems incorporating these products is not covered.
This European Standard does not specify the required level of a given property that should be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender.
Products with a declared thermal conductivity greater than 0,060 W/(m·K) at a mean temperature of 10 °C are not covered by this standard.
This European Standard does not cover products intended to be used for the insulation of the building structure nor for acoustical insulation.
Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus extrudiertem Polystyrolschaum (XPS) - Spezifikation
Diese Europäische Norm legt die Anforderungen an werkmäßig hergestellte Produkte aus extrudiertem Polystyrolschaum fest, die als Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie in einem Betriebstemperaturbereich von etwa − 180 °C bis + 75 °C benutzt werden.
Bei einer Betriebstemperatur unterhalb von − 50 °C sind besondere Prüfungen bezüglich der Eignung der Produkte für den beabsichtigten Anwendungsfall ratsam (z. B. Sauerstoffverflüssigung). In jedem Fall sollten die Empfehlungen des Herstellers beachtet werden.
Die Produkte werden in Form von kaschierten oder unkaschierten Platten, Rohrschalen, Segmenten und vorgeformter Dämmung hergestellt.
Diese Europäische Norm beschreibt die Produkteigenschaften und enthält Verfahren zur Prüfung, Konformitätsbewertung, Kennzeichnung und Etikettierung.
Die von dieser Norm abgedeckten Produkte werden auch in vorgefertigten Wärmedämmsystemen und Mehrschicht-Verbundplatten angewendet; die Eigenschaften von Systemen, in die diese Produkte integriert sind, werden nicht behandelt.
Diese Europäische Norm legt für die einzelnen Eigenschaften keine Leistungsstufen fest, die ein Produkt erreichen sollte, um für einen bestimmten Anwendungsfall tauglich zu sein. Die für bestimmte Anwendungen benötigten Stufen können Regelwerken oder Ausschreibungen entnommen werden.
Diese Norm gilt nicht für Produkte mit einem Nennwert der Wärmeleitfähigkeit größer als 0,060 W/(m ⋅ K) bei einer Mitteltemperatur von 10 °C.
Diese Europäische Norm gilt nicht für Produkte, die zur Dämmung des Bauwerks bestimmt sind und Produkte, die zur Schalldämmung bestimmt sind.
Produits isolants thermiques pour l'équipement du bâtiment et les installations industrielles - Produits manufacturés en mousse de polystyrène extrudé (XPS) - Spécification
La présente Norme européenne spécifie les exigences relatives aux produits manufacturés en mousse de polystyrène extrudé, utilisés pour l’isolation thermique de l’équipement du bâtiment et des installations industrielles, dont la température de service est approximativement comprise entre - 180 °C et + 75 °C.
Pour une température de service inférieure à - 50 °C, des essais particuliers sont recommandés pour s'assurer de l'aptitude à l'emploi du produit dans l'application visée (liquéfaction de l'oxygène, par exemple). Il convient de se référer systématiquement aux conseils du fabricant.
Les produits sont manufacturés sous forme de panneaux, coquilles, segments et articles préfabriqués, avec ou sans parement.
La présente Norme européenne décrit les caractéristiques de ces produits et comprend des modes opératoires d’essai, d’évaluation de la conformité, de marquage et d’étiquetage.
Les produits couverts par la présente norme sont également utilisés dans les systèmes d’isolation thermique préfabriqués et les panneaux composites ; les performances des systèmes incorporant ces produits ne sont pas traitées.
La présente Norme européenne ne spécifie pas le niveau requis d'une propriété donnée qu'il convient qu'un produit atteigne pour démontrer son aptitude à l'emploi dans une application particulière. Les niveaux requis pour une application donnée peuvent être trouvés dans les réglementations et les appels d’offre.
Les produits dont la conductivité thermique déclarée est supérieure à 0,060 W/(m·K) à une température moyenne de 10 °C ne sont pas couverts par la présente norme.
La présente Norme européenne ne couvre ni les produits destinés à l’isolation des structures de bâtiment ni les produits d’isolation acoustique.
Toplotnoizolacijski proizvodi za opremo stavb in industrijske inštalacije - Proizvodi iz ekstrudiranega polistirena (XPS) - Specifikacija
Ta evropski standard določa zahteve za proizvode iz ekstrudiranega polistirena, ki se uporabljajo za toplotno izolacijo opreme stavb in industrijskih inštalacij z razponom delovne temperature približno od –180 °C do 75 °C. OPOMBA Pod delovno temperaturo –50 °C se priporočajo posebni preskusi glede primernosti proizvodov za predvideno vrsto uporabe (npr. utekočinjenje kisika). V vseh primerih naj bi upoštevali napotke proizvajalca. Proizvodi so izdelani v obliki prevlečenih ali neprevlečenih plošč, vodovodnih odsekov, segmentov in montažne opreme. Ta standard opisuje lastnosti proizvodov ter zajema postopke za preskušanje, vrednotenje skladnosti, označevanje in etiketiranje. Proizvodi iz tega standarda se uporabljajo tudi v montažnih sistemih toplotne izolacije in vezanih ploščah; lastnosti sistemov iz teh proizvodov niso opisane. Ta evropski standard ne določa zahtevane ravni določene lastnosti, ki jo mora proizvod doseči, da se dokaže njegova primernost namenu za posamezno vrsto uporabe. Zahtevane ravni za posamezno uporabo je mogoče najti v uredbah in javnih razpisih. Proizvodi z deklarirano toplotno prevodnostjo, višjo od 0,060 W/mK pri povprečni temperaturi 10 °C, v tem standardu niso zajeti. Ta standard ne zajema proizvodov za izolacijo stavbne strukture ali za zvočno izolacijo.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Toplotnoizolacijski proizvodi za opremo stavb in industrijske inštalacije - Proizvodi iz ekstrudiranega polistirena (XPS) - SpecifikacijaWärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus extrudiertem Polystyrolschaum (XPS) - SpezifikationProduits isolants thermiques pour l'équipement du bâtiment et les installations industrielles - Produits manufacturés en mousse de polystyrène extrudé (XPS) - SpécificationThermal insulation products for building equipment and industrial installations - Factory made extruded polystyrene foam (XPS) products - Specification91.100.60Thermal and sound insulating materialsICS:Ta slovenski standard je istoveten z:EN 14307:2015SIST EN 14307:2016en,fr,de01-februar-2016SIST EN 14307:2016SLOVENSKI
STANDARDSIST EN 14307:2010+A1:20131DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14307
December
t r s w ICS
{ sä s r rä x r Supersedes EN
s v u r yã t r r { ªA sã t r s uEnglish Version
Thermal insulation products for building equipment and industrial installations æ Factory made extruded roducts æ Specification Produits isolants thermiques pour l 5équipement du bâtiment et les installations industrielles æ Produits æ Spécification
Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie æ Werkmäßig hergestellte Spezifikation This European Standard was approved by CEN on
t v October
t r s wä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey andUnited Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s w CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s v u r yã t r s w ESIST EN 14307:2016
Factory production control . 20 Annex B (normative)
Determination of the aged values of thermal conductivity . 22 SIST EN 14307:2016
Additional properties . 24 C.1 General . 24 C.2 Behaviour under cyclic loading . 24 C.3 Compressive modulus of elasticity . 24 C.4 Bending strength . 24 C.5 Shear strength . 24 C.6 Deformation under specified compressive load and temperature conditions . 25 C.7 Compressive creep . 25 C.8 Tensile strength perpendicular to facings . 26 C.9 Long term water absorption by diffusion . 26 C.10 Long term water absorption by immersion . 26 C.11 Freeze–thaw resistance . 27 C.12 Apparent density . 27 C.13 Coefficient of thermal expansion . 27 C.14 Closed cell content . 27 Annex ZA (informative)
Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation . 29 ZA.1 Scope and relevant characteristics . 29 ZA.2 Procedures for AVCP of factory made extruded polystyrene foam products . 31 ZA.3 CE Marking and labelling . 38 Bibliography . 40
is the thermal conductivity W/(m·K) D is the declared thermal conductivity W/(m·K)
is the water vapour diffusion resistance factor — Sb is the deviation from squareness of the edge (width or length) mm/m Sd is the deviation from squareness of the edge (thickness) mm/m Smax is the deviation from flatness mm 10 is the compressive stress at 10 % deformation kPa m is the compressive strength kPa v is the deviation from the squareness for pipe section mm/m Wp is the short-term water absorption by partial immersion kg/m2 Z is the water vapour resistance m2 · h · Pa/mg CL is the symbol of the declared level for soluble chloride ions
CS(10\Y) is the symbol of the declared level for compressive stress or strength
DS(TH) is the symbol of the declared value for the dimensional stability under specified temperature and humidity conditions
MU is the symbol of the declared level for water vapour diffusion resistance factor
NA is the symbol of the declared level of soluble sodium ions
pH is the symbol of the declared level of the pH value
SI is the symbol of the declared level of soluble silicate ions
ST(+) is the symbol of the declared level for maximum service temperature
ST(-) is the symbol of the declared level for minimum service temperature
T is the symbol of the declared class for thickness tolerances
WS is the symbol of the declared level for short-term water absorption by partial immersion
Z is the symbol of the declared value for water vapour resistance
3.2.2 Abbreviations used in this standard AVCP is Assessment and Verification of Constancy of Performance (previously named attestation of conformity) DoP is Declaration of Performance FPC is Factory Production Control PTD is Product Type Determination (previously named ITT for Initial Type Test) RtF is Reaction to Fire SBI is Single Burning Item ThIBEII is Thermal Insulation for Building Equipment and Industrial Installations VCP is Verification of Constancy of Performance (previously named evaluation of conformity) XPS is eXtruded PolyStyrene foam 4 Requirements 4.1 General Product properties shall be assessed in accordance with Clause 5. To comply with this standard, products shall meet the requirements of 4.2, and the requirements of 4.3 as appropriate. NOTE
Information on additional properties is given in Annex C. One test result for a product property is the average of the measured values on the number of test specimens given in Table 5. Apparent density is a useful parameter, among others, for the identification but it should not be used as a basis for the quality assessment of XPS products. Apparent density of XPS boards and billets, if voluntary declared by the manufacturer will be determined in accordance with EN 1602, Thermal insulating products for building applications — Determination of the apparent density. Apparent density of pipe sections, if voluntary declared by the manufacturer will be determined in accordance with EN 13470, Thermal insulating products for building equipment and industrial installations — Determination of the apparent density of preformed pipe insulation. SIST EN 14307:2016
values below 0,1 W/(m·K) and in 0,001 W/(m·K) for
values above 0,1 W/(m·K). This shall be used as a reference for the verification of the declaration. When thermal conductivity is declared as a table derived from the equation, rounding upwards to the next 0,001 W/(m·K) has to be done for the full range of the thermal conductivity. NOTE Determinations of the declared thermal conductivity of pipe sections, following EN ISO 8497, having joints in metering area, include the effects of these joints as defined in EN ISO 23993. 4.2.2 Dimensions and tolerances 4.2.2.1 Linear dimensions of boards The length, l, and width, b, shall be determined in accordance with EN 822, the squareness, Sb, in accordance with EN 824, and flatness, Smax, in accordance with EN 825. No test result shall deviate from the declared values by more than the tolerances given in Table 1. Table 1 — Tolerances of length, width, squareness and flatness of boards Length or width mm Tolerances Length or width mm Squareness on length and width Sb mm/m Flatness Smax. mm Less than 1 000 1 000 to 2 000 > 2 000 to 4 000 > 4 000 ±8 ±10 ±10 ±10 5 5 5 5 7,0 14,0 28,0 35,0 SIST EN 14307:2016
¶ dD
¶ 120 > 120 T2 – 1,5 – 1,5 – 1,5 + 1,5 + 1,5 + 1,5 < 50 50
¶ dD
¶ 120 > 120 T3 – 1 – 1 – 1 + 1 + 1 + 1 < 50 50
¶ dD
¶ 120 > 120 4.2.2.3 Dimensions and tolerances of pipe sections and segments The length, l, thickness, d, inside diameter, Di, the deviation from the squareness, v, and the deviation from the linearity, L, of pipe sections and segments shall be tested in accordance with EN 13467. Products with a facing or natural skin shall be tested without removing them. No test result shall deviate from the declared values by more than the tolerances given in Table 3. Tolerances on prefabricated wares may be agreed between the parties. Table 3 — Tolerances for pipe sections and segments Length, l ±10 mm Thickness, d a, ±3 mm or ± 5 % b Inside diameter, Di – 0 mm / + 4 mm or + 2 % b Squareness, v ±6 mm or ± 2 % b Linearity, L ±6 mm a
The tolerances only apply to unfaced products. The thickness of any facing exceeding 2 mm shall be indicated in the manufacturer’s literature. b
The greater value applies. NOTE Smaller tolerances may be declared by a producer. 4.2.3 Dimensional stability Dimensional stability under specified temperature and humidity conditions shall be determined in accordance with EN 1604. The test shall be carried out after storage for 48 h at (23 ± 2) °C and (90 ± 5) % relative humidity. The relative changes in length, l, in width, b, and in thickness, d, shall not exceed 2 %. SIST EN 14307:2016
General The appropriate durability characteristics have been considered and are covered in 4.2.5.2, 4.2.5.3 and 4.2.5.4. 4.2.5.2 Durability of reaction to fire against ageing/degradation and high temperature The reaction to fire performance of XPS products does not change with time within their range of service temperature. 4.2.5.3 Durability of thermal resistance against ageing/degradation The declared thermal conductivity of XPS products does not change with time. This is covered by 4.2.1 thermal conductivity, Annex B determination of the aged value of thermal conductivity and 4.2.2 dimensions and tolerances. 4.2.5.4 Durability of thermal resistance against high temperature The thermal conductivity of XPS products does not change with time at a high temperature within their declared operating temperature range. This is covered by 4.3.2 maximum service temperature (dimensional stability). 4.3 For specific applications 4.3.1 General If there is no intended requirement for a property described in 4.3, for a product in use, then that property does not need to be determined and declared by the manufacturer. XPS pipe sections and prefabricated ware are sawed or abraded from flat boards. If not specified hereafter, the declarations for the specific characteristics correspond to the flat boards used for their fabrication. 4.3.2 Maximum service temperature The maximum service temperature, ST(+), shall be determined in accordance with EN 14706. At the maximum service temperature, ST(+), no test result shall have a variation of dimensions exceeding ± 3 %. SIST EN 14307:2016
· 100 CS(10\Y) 150
· 150 CS(10\Y) 200
· 200 CS(10\Y) 250
· 250 CS(10\Y) 300
· 300 CS(10\Y) 400
· 400 CS(10\Y) 500
· 500 CS(10\Y) 600
· 600 CS(10\Y) 700
· 700 CS(10\Y) 800
· 800 CS(10\Y) 1000
· 1 000 4.3.5 Water vapour diffusion transmission properties Water vapour diffusion transmission properties shall be determined in accordance with EN 12086, and declared as the water vapour diffusion resistance factor, , for homogeneous products and as the water vapour resistance, Z, for faced or non-homogeneous products. No test result of
shall be less than the declared level, MU, chosen from the following levels: 50; 80; 100; 150; 200; 250; 300. If Z is declared, no test result of Z shall be less than the declared value. Alternatively, for the declaration of water vapour transmission properties, the values quoted in EN ISO 10456 may be used. SIST EN 14307:2016
of the range. If facings have been removed, this and the reason for the remove shall be stated in the test report. 5.3.3 Reaction to fire The tests shall be carried out in accordance with EN 13501-1. Rules for mounting and fixing are given in EN 15715:2009. Annex A of EN 15715:2009 gives tables for product and installation parameters for flat products and pipe insulation products as placed on the market. Installation parameters for standardized assemblies are only given for flat products. A conditioning period of six weeks applies before testing. SIST EN 14307:2016
number of measurements to get one test result Specific conditions No. Title Flat / Board Cylindrical 4.2.1 Thermal conductivity EN 12667 or EN 12939 EN 12667 or EN 12939 for Di > 500 EN ISO 8497 for Di
¶ 500 See EN 12667, EN 12939 or EN ISO 8497 1
See Annex B 4.2.2.1 Board length and width EN 822
Full size 1
Board squareness EN 824
Full size 1 Where relevant the method to determine the squareness of the edge of boards with special edge treatment shall be agreed between parties. Board flatness EN 825
Full size 1
4.2.2.2 Board thickness EN 823
Full size 1 Load (250 ± 5) Pa 4.2.2.3 Pipe section dimensions and tolerances
EN 13467 Full size 1
4.2.3 Dimensional stability EN 1604
200 × 200 2 Condition specimens for 45 days. Test conditions: 23 °C, 90 % RH. 4.2.4 Reaction to fire of the product as placed on the market See EN 13501–1, EN ISO 11925-2 and EN 13823 See EN 15715:2009 4.3.2 Maximum service temperature EN 14706
Boards (100 × 100) × d d = 50 or 100 3 Temperature gradient
50 K/h maximum Condition specimen
45 days
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...