SIST EN ISO 1269:2007

SLOVENSKI STANDARD
01-april-2007
3ROLPHUQLPDWHULDOL+RPRLQNRSROLPHULYLQLONORULGD'RORþHYDQMHKODSQHVQRYL
YNOMXþQR]YRGR,62
Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of volatile
matter (including water) (ISO 1269:2006)
Kunststoffe - Vinylchlorid-Homo- und Copolymerisate - Bestimmung der flüchtigen
Bestandteile (einschließlich Wasser) (ISO 1269:2006)
Plastiques - Résines d'homopolymeres et de copolymeres de chlorure de vinyle -
Détermination des matieres volatiles (y compris l'eau) (ISO 1269:2006)
Ta slovenski standard je istoveten z: EN ISO 1269:2006
ICS:
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 1269
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2006
ICS 83.080.20
English Version
Plastics - Homopolymer and copolymer resins of vinyl chloride -
Determination of volatile matter (including water) (ISO
1269:2006)
Plastiques - Résines d'homopolymères et de copolymères Kunststoffe - Vinylchlorid-Homo- und Copolymerisate -
de chlorure de vinyle - Détermination des matières volatiles Bestimmung der flüchtigen Bestandteile (einschließlich
(y compris l'eau) (ISO 1269:2006) Wasser) (ISO 1269:2006)
This European Standard was approved by CEN on 11 November 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1269:2006: E
worldwide for CEN national Members.

Foreword
This document (EN ISO 1269:2006) has been prepared by Technical Committee ISO/TC 61
"Plastics" in collaboration with Technical Committee CEN/TC 249 "Plastics", the secretariat of
which is held by IBN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by May 2007, and conflicting national standards
shall be withdrawn at the latest by May 2007.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice
The text of ISO 1269:2006 has been approved by CEN as EN ISO 1269:2006 without any
modifications.
INTERNATIONAL ISO
STANDARD 1269
Third edition
2006-11-15
Plastics — Homopolymer and copolymer
resins of vinyl chloride — Determination
of volatile matter (including water)
Plastiques — Résines d'homopolymères et de copolymères de chlorure
de vinyle — Détermination des matières volatiles (y compris l'eau)

Reference number
ISO 1269:2006(E)
©
ISO 2006
ISO 1269:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
©
ii ISO 2006 – All rights reserved

ISO 1269:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this doc
...