SIST EN 840-5:2000/A1:2000
(Amendment)Mobile waste containers - Part 5: Performance requirements and test methods
Mobile waste containers - Part 5: Performance requirements and test methods
Migrated from Progress Sheet (TC Comment) (2000-07-10): UAP of 4 months (TC Res 49/1998) (CC/990315)
Fahrbare Abfallsammelbehälter - Teil 5: Anforderungen an die Ausführung und Prüfverfahren
Conteneurs roulants a déchets - Partie 5: Exigences de performance et méthodes d'essai
Mobile waste containers - Part 5: Performance requirements and test methods
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 840-5:2000/A1:2000
01-december-2000
Mobile waste containers - Part 5: Performance requirements and test methods
Mobile waste containers - Part 5: Performance requirements and test methods
Fahrbare Abfallsammelbehälter - Teil 5: Anforderungen an die Ausführung und
Prüfverfahren
Conteneurs roulants a déchets - Partie 5: Exigences de performance et méthodes
d'essai
Ta slovenski standard je istoveten z: EN 840-5:1997/A1:2000
ICS:
13.030.40 Naprave in oprema za Installations and equipment
ods
...
This May Also Interest You
This European Standard provides all of the information required in order to efficiently perform, and in standardized conditions, the determination, the declaration and the verification of noise emission values of refuse collection vehicles.
The use of this annex ensures the reproducibility of the determination of noise emission values within the limits established for the accuracy grade of the basic standard used to determine noise emission values. The methods used to determine these noise emission values, corresponding to this normative annex, are grade 2 accuracy measurement methods.
This standard deals with the noise measurement conditions for the types of RCVs defined and described in the standards of the EN 1501 series
This European Standard applies to machines which are manufactured after the date of approval of this standard by CEN.
- Standard23 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft19 pagesEnglish languagesale 10% offe-Library read for×1 day
- 19-Jun-2022
- 28-May-2023
- 13.030.40
- 17.140.30
- 43.160
- 2006/42/EC
- M/396
- M/BC/CEN/91/1
- I13
This document defines the standard for exchanging stationary waste collection container information between the collection container system and the back-office systems.
This document defines the way to exchange data between the "Communication Management System" of the collection container and the "Back-Office Systems".
The exchange of data between the "Collection Container Systems" and the "Communication Management Systems" or the "Back-Office Systems" is excluded.
This document targets two streams of information in the waste processing industry:
- The processing of transactions and system information for the deposit of waste from the communication management systems to the back office systems.
- The processing of authorization and configuration information from the back-office systems to the communication management systems.
- Standard25 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft24 pagesEnglish languagesale 10% offe-Library read for×1 day
This CWA provides guidance for the implementation of biowaste selective collection schemes.
This CWA also paves the way to increase citizen engagement, as this is crucial for the successful implementation of urban biowaste selective collection schemes.
It is intended to be used by city managers and municipal waste managers with interest in implementing the selective collection of urban biowaste to produce high quality biowaste (i.e., minimal presence of non-required fractions) which can be then used in robust valorization processes with attractive business cases.
- Standardization document19 pagesEnglish languagesale 10% offe-Library read for×1 day
- Technical report19 pagesEnglish languagesale 10% offe-Library read for×1 day
This European standard specifies the essential requirements of stationary systems for production of brines for winter road maintenance and includes tests of these requirements. Battery limits: chloride and water inlet to the saturator, brine outlet to the spreading machine. Within the scope are storage and loading/unloading equipment also.
The following points are not covered by this standard:
- System and construction requirements;
- Requirements according national legislations.
- Standard21 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft20 pagesEnglish languagesale 10% offe-Library read for×1 day
This European Standard gives general guidelines for the hydraulic placement of extractive wastes applicable, in particular, to the extractive industries.
The scope of this European Standard includes any dam, confining embankment or other structure serving to contain, retain, confine or otherwise support such wastes on surface in a terrestrial environment.
This standard therefore addresses the characterisation of the extractive waste for the purposes of hydraulic placement in the MWF both as part of the confining embankment and for safe storage, and in addition:
- specifies minimum requirements for the data to be acquired before the design and execution stage of a hydraulic fill project;
- provides guidelines for the selection of the type of confining embankment appropriate for the selected site;
- provides guidelines for the selection and characterisation of the construction materials;
- establishes general principles on how to design and execute the hydraulic fill project from pre deposition through operation to closure and rehabilitation;
- provides guidelines for monitoring and quality control of all stages of the hydraulic fill project to ensure long-term safety and stability.
- Standard98 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft85 pagesEnglish languagesale 10% offe-Library read for×1 day
This document deals with all significant hazards, hazardous situations and events relevant to lifting devices used for the emptying of designated refuse containers into RCVs and their fitting onto the RCVs when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer throughout their foreseeable lifetime as defined in Clause 4.
This document is applicable to the design and construction of the refuse container lifting devices and the mounting of other lifting devices so as to ensure that they are fitted for their function and can be operated, adjusted and maintained during their entire lifetime. It is not applicable to the end of life of the lifting devices.
This document describes and gives the safety requirements of the lifting devices for emptying refuse containers and their interfaces with the corresponding parts of the RCVs and will be used in conjunction with prEN 1501-1 for the rear, side and front loaded RCVs. It refers to EN 1501-4 for the noise test code.
This document is not applicable to:
- operation in severe conditions e.g. extreme environmental conditions such as:
- temperatures below −25 °C and above +40 °C;
- tropical environment;
- wind velocity in excess of 75 km/h;
- contaminating environment;
- corrosive environment;
- operation in potentially explosive atmospheres;
- lifting and transportation of persons;
- emptying refuse containers other than those manufactured according to EN 840 (all parts), EN 12574 (all parts), EN 13071 (all parts), and those described as paladin, diamond, skip containers;
- loading bulky refuse by means of platform or forks;
- handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
- operation on ships;
- fitting and operation on stationary compactors.
This document is not applicable to machinery which is manufactured before the date of its publication by CEN.
- Standard95 pagesEnglish languagesale 10% offe-Library read for×1 day
- 25-Apr-2018
- 15-Apr-2021
- 13.030.40
- 43.160
- 2006/42/EC
- M/396
- I13
This document applies to side loaded refuse collection vehicle (RCV), as defined in prEN 1501-1.
This document deals with all significant hazards, hazardous situations and events relevant to the side loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the side loaded RCV so as to ensure that it is fit for its intended function and can be operated, moved, cleaned (including unblocking), adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the side loaded RCV.
This document describes and defines the safety requirements of side loaded RCV excluding the interface with the lifting device(s) and excluding the lifting device itself and excluding loader cranes, which could be mounted on the RCV.
Safety requirements for the lifting device(s) including the loader cranes and the interface to the RCV are defined in prEN 1501-5.
Safety requirements for loader cranes are defined in EN 12999.
This document also applies to compactors, operated on a truck for collecting purposes.
This document is not applicable to:
- below −25 °C and above +40 °C temperatures;
- tropical environment;
- wind velocity in excess of 75 km/h;
- contaminating environment;
- corrosive environment;
- operation in potentially explosive atmospheres;
- handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
- operation on ships.
This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.
- Standard62 pagesEnglish languagesale 10% offe-Library read for×1 day
- 25-Apr-2018
- 15-Apr-2021
- 13.030.40
- 43.160
- 2006/42/EC
- M/396
- I13
This document applies to rear loaded refuse collection vehicles (RCV), as defined in 3.2.
This document deals with all significant hazards, hazardous situations and events relevant to the rear loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the rear loaded RCV so as to ensure that it is fit for its function and can be operated, adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the rear loaded RCV.
This document describes and defines the safety requirements of rear loaded RCVs excluding the interface tailgate/discharge door with the lifting device(s) and the lifting device(s) as illustrated in Figure A.1.
Safety requirements for the lifting device(s) and the interface with the tailgate/discharge door are defined in prEN 1501-5. Safety requirements for loader cranes are defined in EN 12999.
This European Standard is not applicable to:
- operation in severe conditions, e.g. extreme environmental conditions such as:
- below -25 °C and above +40 °C temperatures;
- tropical environment;
- wind velocity in excess of 75 km/h;
- contaminating environment;
- corrosive environment;
- operation in potentially explosive atmospheres;
- handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
- operation on ships.
This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.
- Standard78 pagesEnglish languagesale 10% offe-Library read for×1 day
- 25-Apr-2018
- 15-Apr-2021
- 13.030.40
- 43.160
- 2006/42/EC
- M/396
- I13
This document applies to front loaded refuse collection vehicle (RCV), as defined in 3.2 with closed system defined in 3.13.
This document deals with all significant hazards, hazardous situations and events relevant to the front loaded RCV, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, throughout its foreseeable lifetime, as defined in Clause 4.
This document is applicable to the design and construction of the front loaded RCV so as to ensure that it is fitted for its function and can be operated adjusted and maintained during its entire lifetime. It is not applicable to the end of life of the front loaded RCV.
prEN 1501-3 describes and defines the safety requirements of front loaded RCV excluding the interface with the lifting device(s) and excluding the lifting device itself and excluding loader cranes, which could be mounted on the RCV.
Safety requirements for the lifting device(s), loader cranes and their interface to the RCV are defined in prEN 1501-5.
Safety requirements for loader cranes are defined in EN 12999. Additional requirements to loader cranes installed as a loading device for handling containers for refuse or recyclable material on RCVs are defined in prEN 1501 5.
This document also applies to compactors, operated on a truck for collecting purposes.
This document is not applicable to:
- operation in severe conditions e.g. extreme environmental conditions such as:
- below −25 °C and above +40 °C temperatures;
- tropical environment;
- wind velocity in excess of 75 km/h;
- contaminating environment;
- corrosive environment;
- operation in potentially explosive atmospheres;
- handling of loads the nature of which could lead to dangerous situations (e.g. hot refuses, acids and bases, radioactive materials, contaminated refuse, especially fragile loads, explosives);
- operation on ships.
This document is not applicable to machinery which is manufactured before the date of publication of this document by CEN.
- Standard54 pagesEnglish languagesale 10% offe-Library read for×1 day
- 25-Apr-2018
- 15-Apr-2021
- 13.030.40
- 43.160
- 2006/42/EC
- M/396
- I13
This European Standard specifies the safety requirements for the design, manufacture and information for the safe use of compactors that compact waste material or recyclable fractions (e. g. paper, plastics, textiles, cans, cardboard, mixed waste), hereafter referred to as materials.
This European Standard applies to:
- compactors using a horizontally moving screw, pendulum or plate as compacting part and where the materials move horizontally; and
- compactors that are mechanically fed and/or fed by hand.
These compactors can be:
- static compactors;
- transportable compactors;
- traversing systems.
The scope includes:
- any integral mechanical feed equipment (e.g. bin lift);
- feed hoppers/openings;
- any integral pre-conditioning equipment in the hopper (e.g. perforators, pre-crushing devices and shredders);
- any integral material flow control equipment;
- the interface between the compactor and any feed equipment (except those excluded from the scope).
The scope of this European Standard does not cover:
- compactors that are covered by EN 1501 (all parts);
- underground compactors, however if these compactors can be used above ground this standard applies;
- compactors using thermal technologies for compaction;
- vacuum compactors;
- compactors where materials are compacted vertically;
- containers for static compactors, however the interface between the compaction unit and the container is included;
- bins in which materials are collected for feeding into the compactor;
- any up-stream pre-treatment equipment that is not integral to the machine and is used to treat the materials before they are fed into the feed opening of the compactor;
- vehicles including lifting equipment used to collect and transport the compactor or container;
- cranes, lift trucks or other transportable plant used to load materials into the feed hopper/opening and the hazards arising out of using this equipment to load;
- any suction or dust control equipment.
This European standard does not cover the lifting and transport of transportable compactors.
This European Standard does not apply to hazards arising from the materials being processed (e.g. asbestos, clinical waste, aerosol containers).
All hazards mentioned in Clause 4 are dealt with in this European Standard.
This European Standard is not applicable for compactors which are manufactured before the date of its publication as an EN.
- Standard50 pagesEnglish languagesale 10% offe-Library read for×1 day
- 10-Jan-2021
- 13.030.40
- 43.160
- 2006/42/EC
- M/396
- VSN
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.