SIST EN ISO 22568-3:2019

SLOVENSKI STANDARD
SIST EN ISO 22568-3:2019
01-julij-2019
Nadomešča:
SIST EN 12568:2010
Ščitniki nog in stopal - Zahteve in preskusne metode za sestavne dele obutve - 3.
del: Kovinski vložki, odporni proti prediranju (ISO 22568-3:2019)
Foot and leg protectors - Requirements and test methods for footwear components - Part
3: Metallic perforation resistant inserts (ISO 22568-3:2019)
Fuß- und Beinschutz - Anforderungen und Prüfverfahren für Schuhkomponenten - Teil 3:
Metallische perforationsbeständige Einlagen (ISO 22568-3:2019)
Protecteurs du pied et de la jambe - Exigences et méthodes d'essais pour les
composants de chaussure - Partie 3: Inserts anti-perforation métalliques (ISO 22568-
3:2019)
Ta slovenski standard je istoveten z: EN ISO 22568-3:2019
ICS:
13.340.50 Varovanje nog in stopal Leg and foot protection
SIST EN ISO 22568-3:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 22568-3:2019

---------------------- Page: 2 ----------------------

SIST EN ISO 22568-3:2019


EN ISO 22568-3
EUROPEAN STANDARD

NORME EUROPÉENNE

April 2019
EUROPÄISCHE NORM
ICS 13.340.50 Supersedes EN 12568:2010
English Version

Foot and leg protectors - Requirements and test methods
for footwear components - Part 3: Metallic perforation
resistant inserts (ISO 22568-3:2019)
Protecteurs du pied et de la jambe - Exigences et Fuß- und Beinschutz - Anforderungen und
méthodes d'essais pour les composants de chaussure - Prüfverfahren für Schuhkomponenten - Teil 3:
Partie 3: Inserts anti-perforation métalliques (ISO Metallische perforationsbeständige Einlagen (ISO
22568-3:2019) 22568-3:2019)
This European Standard was approved by CEN on 25 February 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22568-3:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 22568-3:2019
EN ISO 22568-3:2019 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 22568-3:2019
EN ISO 22568-3:2019 (E)
European foreword
This document (EN ISO 22568-3:2019) has been prepared by Technical Committee ISO/TC 94
"Personal safety -- Personal protective equipment" in collaboration with Technical Committee CEN/TC
161 “Foot and leg protectors” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2019, and conflicting national standards shall
be withdrawn at the latest by October 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12568:2010.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 22568-3:2019 has been approved by CEN as EN ISO 22568-3:2019 without any
modification.


3

---------------------- Page: 5 ----------------------

SIST EN ISO 22568-3:2019

---------------------- Page: 6 ----------------------

SIST EN ISO 22568-3:2019
INTERNATIONAL ISO
STANDARD 22568-3
First edition
2019-03
Foot and leg protectors —
Requirements and test methods for
footwear components —
Part 3:
Metallic perforation resistant inserts
Protecteurs du pied et de la jambe — Exigences et méthodes d'essais
pour les composants de chaussure —
Partie 3: Inserts anti-perforation métalliques
Reference number
ISO 22568-3:2019(E)
©
ISO 2019

---------------------- Page: 7 ----------------------

SIST EN ISO 22568-3:2019
ISO 22568-3:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 22568-3:2019
ISO 22568-3:2019(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements for metallic perforation resistant insert . 1
4.1 General . 1
4.2 Resistance to nail perforation . 2
4.3 Flexing resistance . 2
4.4 Corrosion resistance . 3
5 Test methods for the metallic perforation resistant inserts. 3
5.1 Determination of perforation resistance . 3
5.1.1 Apparatus . 3
5.1.2 Test sample . 4
5.1.3 Test procedure . 4
5.1.4 Test report . 6
5.2 Determination of flexing resistance . 6
5.2.1 Apparatus . 6
5.2.2 Sampling. 6
5.2.3 Test procedure . 6
5.2.4 Results . 7
5.2.5 Test report . 8
5.3 Determination of corrosion resistance . 8
5.3.1 Preliminary examination . 8
5.3.2 Test procedure . 8
5.3.3 Test report . 9
6 Marking . 9
Bibliography .10
© ISO 2019 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 22568-3:2019
ISO 22568-3:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 94, Personal safety — Personal protective
equipment, Subcommittee SC 3, Foot protection.
A list of all parts in the ISO 22568 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 22568-3:2019
ISO 22568-3:2019(E)

Introduction
ISO 20345, ISO 20346 and ISO 20347 are related to safety, protective and occupational footwear which
define the performance and required properties of the footwear. On introducing these standards
all national standards relating to metallic perforation resistant inserts were withdrawn leaving the
manufacturers of these items with no means of demonstrating the performance of their products. This
document has been prepared to allow manufacturers to demonstrate the performance level of the
metallic perforation resistant inserts before being inserted into the footwear.
Metallic perforation resistant inserts and materials complying with the requirements of this document
are suitable components of “PPE footwear”.
© ISO 2019 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 22568-3:2019

---------------------- Page: 12 ----------------------

SIST EN ISO 22568-3:2019
INTERNATIONAL STANDARD ISO 22568-3:2019(E)
Foot and leg protectors — Requirements and test methods
for footwear components —
Part 3:
Metallic perforation resistant inserts
1 Scope
This document specifies requirements and test methods for the metallic perforation resistant inserts
with resistance agains
...