SIST EN ISO/IEC 15421:2024

SLOVENSKI STANDARD
01-junij-2024
Nadomešča:
SIST EN ISO/IEC 15421:2003
Informacijska tehnologija - Tehnike za samodejno razpoznavanje in zajem
podatkov - Specifikacije za glavni preskus črtnih kod (ISO/IEC 15421:2010)
Information technology - Automatic identification and data capture techniques - Bar code
master test specifications (ISO/IEC 15421:2010)
Informationstechnik - Verfahren der automatischen Identifikation und Datenerfassung -
Testspezifikationen für Strichcode-Master (ISO/IEC 15421:2010)
Technologies de l'information - Techniques automatiques d'identification et de capture
des données - Spécifications pour essai des codes à barres de base (ISO/IEC
15421:2010)
Ta slovenski standard je istoveten z: EN ISO/IEC 15421:2024
ICS:
35.040.50 Tehnike za samodejno Automatic identification and
razpoznavanje in zajem data capture techniques
podatkov
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO/IEC 15421
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2024
EUROPÄISCHE NORM
ICS 35.040.50
English Version
Information technology - Automatic identification and data
capture techniques - Bar code master test specifications
(ISO/IEC 15421:2010)
Technologies de l'information - Techniques Informationstechnik - Verfahren der automatischen
automatiques d'identification et de capture des Identifikation und Datenerfassung -
données - Spécifications pour essai des codes à barres Testspezifikationen für Strichcode-Master (ISO/IEC
de base (ISO/IEC 15421:2010) 15421:2010)
This European Standard was approved by CEN on 16 March 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO/IEC 15421:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
The text of ISO/IEC 15421:2010 has been prepared by Technical Committee ISO/IEC JTC 1 "Automatic
identification and data capture techniques” of the International Organization for Standardization (ISO)
and has been taken over as EN ISO/IEC 15421:2024 by Technical Committee CEN/TC 225 “AIDC
technologies” the secretariat of which is held by TSE.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2024, and conflicting national standards
shall be withdrawn at the latest by September 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO/IEC 15421:2010 has been approved by CEN as EN ISO/IEC 15421:2024 without any
modification.
INTERNATIONAL ISO/IEC
STANDARD 15421
Second edition
2010-06-01
Information technology — Automatic
identification and data capture
techniques — Bar code master test
specifications
Technologies de l'information — Techniques automatiques
d'identification et de capture des données — Spécifications pour essai
de base des codes à barres
Reference number
ISO/IEC 15421:2010(E)
©
ISO/IEC 2010
ISO/IEC 15421:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO/IEC 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO/IEC 2010 – All rights reserved

ISO/IEC 15421:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Symbols.2
5 Physical requirements .3
5.1 Material .3
5.2 Physical requirements controlled by the manufacturing process.3
5.3 Tolerances.3
5.4 Bar edge characteristics.5
5.5 Defects.5
5.6 Quiet zones .5
5.7 Corner marks .6
5.8 Optical densities.6
5.9 Orientation .6
5.10 Polarity.6
5.11 Encodation .6
5.12 Human readable interpretation .6
6 Test methods .7
6.1 Bar and space width measurement .7
6.2 Test report and traceability .8
Annex A (informative) Optical density profiles.9

© ISO/IEC 2010 – All rights reserved iii

ISO/IEC 15421:2010(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information
technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of the joint technical committee is to prepare International Standards. Draft International
Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as
an International Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.
ISO/IEC 15421 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology,
Subcommittee SC 31, Automatic identification and data capture techniques.
This second edition cancels and replaces the first edition (ISO/IEC 15421:2000), which has been technically
revised.
iv © ISO/IEC 2010 – All rights reserved

ISO/IEC 15421:2010(E)
Introduction
The technology of bar coding is based on the recognition of patterns encoded in bars and spaces of specified
dimensions. A wide variety of methods exists by which these bar and space patterns can be reproduced as a
physical image. Conventional printing processes such as offset lithography, photogravure, letterpress, screen
process, hot foil stamping and flexography require one or more intermediate image carriers, for example
artwork, photographic film, printing plates or cylinders, screens or dies.
The term bar code master refers to the first physical image of the complete bar code symbol from which the
other image carriers can be produced. Some processes directly create an image carrier without generating a
master that would be covered by this International Standard. In order to make allowances for variability of the
production processes, and to ensure the correct encoding of the data to be represented, certain procedures
need to be performed during the preparation of the bar code master.
This International Standard does not define the procedures but states the requirements for a bar code master.
© ISO/IEC 2010 – All rights reserved v

INTERNATIONAL STANDARD ISO/IEC 15421:2010(E)

Information technology — Automatic identification and data
capture techniques — Bar code master test specifications
1 Scope
This International Standard specifies the requirements and test methods for physical and related attributes of
a bar code master. It covers all forms of bar code master, irrespective of the mode of origination of the initial
image, intended for reproduction by conventional printing proc
...