SIST EN ISO 1181:2005

SLOVENSKI STANDARD
SIST EN ISO 1181:2005
01-marec-2005
Vlaknene vrvi – Manila in sisal - 3-, 4- in 8-pramenske vrvi (ISO 1181:2004)
Fibre ropes - Manila and sisal - 3-, 4- and 8-strand ropes (ISO 1181:2004)
Fasereile - Manila und Sisal - 3-, 4- und 8-litzige Seile (ISO 1181:2004)
Cordages en fibres - Abaca (manille) et sisal - Cordages a 3, 4 et 8 torons (ISO
1181:2004)
Ta slovenski standard je istoveten z: EN ISO 1181:2004
ICS:
59.080.50 Vrvi Ropes
SIST EN ISO 1181:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 1181:2005

---------------------- Page: 2 ----------------------

SIST EN ISO 1181:2005



EUROPEAN STANDARD
EN ISO 1181

NORME EUROPÉENNE

EUROPÄISCHE NORM
November 2004
ICS 59.080.50 Supersedes EN 698:1995
English version
Fibre ropes - Manila and sisal - 3-, 4- and 8-strand ropes (ISO
1181:2004)
Cordages en fibres - Abaca (manille) et sisal - Cordages à
3, 4 et 8 torons (ISO 1181:2004)
This European Standard was approved by CEN on 12 October 2004.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.




EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1181:2004: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 1181:2005
EN ISO 1181:2004 (E)


Foreword

This document (EN ISO 1181:2004) has been prepared by Technical Committee CEN/TC 248
"Textiles and textile products", the secretariat of which is held by BSI, in collaboration with
Technical Committee ISO/TC 38 "Textiles".

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by May 2005, and conflicting national standards
shall be withdrawn at the latest by May 2005.

This document supersedes EN 698:1995.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
2

---------------------- Page: 4 ----------------------

SIST EN ISO 1181:2005


INTERNATIONAL ISO
STANDARD 1181
Third edition
2004-11-01

Fibre ropes — Manila and sisal —
3-, 4- and 8-strand ropes
Cordages en fibres — Abaca (manille) et sisal — Cordages à 3,
4 et 8 torons




Reference number
ISO 1181:2004(E)
©
ISO 2004

---------------------- Page: 5 ----------------------

SIST EN ISO 1181:2005
ISO 1181:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2004 – All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 1181:2005
ISO 1181:2004(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 1
4 Designation. 1
5 General requirements . 2
6 Lubrication and finish. 3
7 Physical properties . 3
8 Marking. 6

© ISO 2004 – All rights reserved iii

---------------------- Page: 7 ----------------------

SIST EN ISO 1181:2005
ISO 1181:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 1181 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 248, Textiles and textile products, in collaboration with Technical Committee ISO/TC 38, Textiles, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 1181:1990), which has been technically
revised.

iv © ISO 2004 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 1181:2005
INTERNATIONAL STANDARD ISO 1181:2004(E)

Fibre ropes — Manila and sisal — 3-, 4- and 8-strand ropes
1 Scope
This International Standard specifies requirements for 3-strand hawser-laid and 4-strand shroud-laid ropes
and 8-strand braided ropes for general service made of manila and sisal and gives rules for their designation.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (inclu
...