ISO 12800
(Main)Nuclear fuel technology — Guidelines on the measurement of the specific surface area of uranium dioxide and plutonium dioxide powders by the BET method
- Abstract
ISO 12800:2017 gives guidelines on the determination of the specific surface area of as-fabricated uranium dioxide powder by volumetric or gravimetric determination of the amount of nitrogen adsorbed on the powder, and can be applied to other similar materials, e.g. U3O8, UO2-PuO2 powders, and other bodies with similar surface areas, e.g. powder granules or green pellets, provided that the conditions described are fulfilled. Modifications using other adsorbing gases are included. The method is relevant as long as the expected value is in the range between 1 m2/g and 10 m2/g.
- Status
- Not Published
- Technical Committee
- ISO/TC 85/SC 5 - Nuclear installations, processes and technologies
- Drafting Committee
- ISO/TC 85/SC 5/WG 1 - Analytical methodology in the nuclear fuel cycle
- Current Stage
- 6000 - International Standard under publication
- Start Date
- 12-Nov-2026
- Completion Date
- 14-Nov-2026
Buy Documents
ISO/FDIS 12800 - Nuclear fuel technology — Guidelines on the measurement of the specific surface area of uranium dioxide and plutonium dioxide powders by the BET method
REDLINE ISO/FDIS 12800 - Nuclear fuel technology — Guidelines on the measurement of the specific surface area of uranium dioxide and plutonium dioxide powders by the BET method
ISO/FDIS 12800 - Technologie du combustible nucléaire — Lignes directrices pour le mesurage de l'aire massique (surface spécifique) des poudres d'oxyde d'uranium et de plutonium par la méthode BET
ISO 12800 is an ISO standard for nuclear fuel technology. It gives guidelines for measuring the specific surface area of uranium dioxide and plutonium dioxide powders by the Brunauer-Emmett-Teller (BET) method, mainly for use in nuclear fuel fabrication and related laboratory work. The document focuses on how to prepare the sample, make the adsorption measurement, calculate the result, and report it.
What does ISO 12800 specify?
ISO 12800 specifies a BET-based guideline for determining the specific surface area of as-fabricated uranium dioxide and plutonium dioxide powders by measuring nitrogen adsorption volumetrically or gravimetrically. It also extends to similar materials and related forms when the stated conditions are met, including modifications that use other adsorbing gases.
The standard is organized into seven main clauses:
- Scope
- Normative references
- Terms and definitions
- Principle
- Procedure
- Expression of results
- Test report
Clause 4 explains the BET principle and the assumptions behind it. Clause 5 sets out the measurement procedures, and Clause 6 covers the calculation and reporting of results.
What are the key requirements of ISO 12800?
ISO 12800 is built around a few practical conditions that determine whether the BET method can be applied and how the measurement should be carried out.
- The material must be suitable for BET adsorption measurement - Clause 4.3 limits the method to materials where nitrogen is not adsorbed in an incompatible way, does not react chemically, all pores are accessible to nitrogen, and the adsorption curve is type 2 or type 4. In practice, this is the first check before using the method.
- The expected surface area must fall in the method range - the scope states the method is relevant for uranium dioxide powders in the range from 1 m2/g to 10 m2/g, and for plutonium dioxide powders from 0.1 m2/g to 45 m2/g. This matters because the chosen sample mass and the sensitivity of the instrument depend on the target range.
- The sample must be cleaned before adsorption is measured - Clause 5.1 requires removal of water vapour and other surface impurities before measurement. Evacuation or purified inert gas may be used, but the conditions must avoid decomposition, sintering, or changes in crystal structure.
- Pretreatment depends on the powder type - Clause 5.1.2 gives guidance for uranium dioxide powders, including vacuum pumping to constant pressure and heating under controlled conditions; Clause 5.1.3 gives a different desorption approach for plutonium dioxide powders because they adsorb strongly. In practice, the pretreatment step is critical because it affects the measured surface area.
- The measurement can be volumetric, gravimetric, or dynamic - Clauses 5.2, 5.3, and 5.5 describe these routes. Volumetric methods use pressure changes in a calibrated bulb, gravimetric methods use a microbalance, and the dynamic method uses a carrier gas stream and a katharometer.
- A multipoint BET result needs several equilibrium points - Clause 5.4 requires at least three data points in the relative-pressure region 0.05 to 0.35 for the multipoint method. A single-point method is allowed only when lower accuracy is acceptable and the BET constant is sufficiently high.
- Results must be calculated and reported with uncertainty - Clause 6 requires BET calculation of the specific surface area and reporting of expanded uncertainty in accordance with ISO/IEC Guide 98-3. Clause 6 also notes that the apparatus should be calibrated with a certified reference material, such as those proposed in ISO 9277.
Who uses ISO 12800?
ISO 12800 is used by people who measure or control powder surface area in nuclear fuel fabrication. Typical users include laboratory analysts, metrology staff, quality managers, process engineers, and buyers who need to specify or verify powder characteristics.
In practice, they use it to prepare samples, choose a suitable adsorption method, calculate specific surface area, check instrument performance, and document results in a way that can be compared between laboratories.
What changed in ISO 12800 from the previous edition?
ISO 12800:2026 cancels and replaces ISO 12800:2017, and the standard says it has been technically revised.
The changes stated in the foreword are:
- the table of contents was adaptively revised
- Figure 1 in 4.2 was replaced
- new Subclauses 5.1.1 and 5.1.2 were added as headings with carried-forward content
- new Subclauses 5.1.3 and 5.1.4 were added with new text
- Clause 5.2 was partially revised
- several editorial changes were made
Which standards are used with ISO 12800?
ISO 12800 refers to ISO/IEC Guide 98-3 for expressing measurement uncertainty in the test report. That matters because the reported result must include an expanded uncertainty and a coverage factor.
ISO 9277 is the related BET gas-adsorption standard cited in the calculation and calibration discussion. In practice, it provides a familiar reference point for specific surface area work and for calibration with certified reference materials.
What does the ISO 12800 document contain?
ISO 12800 contains the BET principle, the adsorption-curve classification, the sample pretreatment guidance, and the measurement routes for volumetric, gravimetric, dynamic, and alternative methods. It also includes the calculation equations for multipoint and single-point determination, plus the definitions of the symbols used in those equations.
The document includes Figure 1 on adsorption-isotherm types, Figure 2 on the BET line, and Table 1 with standard occupied areas for different adsorbing gases. These elements support data reduction and method selection in laboratory work.
Clause 7 gives the test report content, including sample identification, the measurement result with uncertainty, test location and date, reference materials used, and the procedural details needed to understand or repeat the measurement.
Relations
- Effective Date
- 12-Feb-2026
- Effective Date
- 18-Jan-2025
Buy Documents
ISO/FDIS 12800 - Nuclear fuel technology — Guidelines on the measurement of the specific surface area of uranium dioxide and plutonium dioxide powders by the BET method
REDLINE ISO/FDIS 12800 - Nuclear fuel technology — Guidelines on the measurement of the specific surface area of uranium dioxide and plutonium dioxide powders by the BET method
ISO/FDIS 12800 - Technologie du combustible nucléaire — Lignes directrices pour le mesurage de l'aire massique (surface spécifique) des poudres d'oxyde d'uranium et de plutonium par la méthode BET
Get Certified
Connect with accredited certification bodies for this standard

DNV
DNV is an independent assurance and risk management provider.

Lloyd's Register
Lloyd's Register is a global professional services organisation specialising in engineering and technology.

DNV Energy Systems
Energy and renewable energy certification.
Sponsored listings
Frequently Asked Questions
ISO 12800 is a draft published by the International Organization for Standardization (ISO). Its full title is "Nuclear fuel technology — Guidelines on the measurement of the specific surface area of uranium dioxide and plutonium dioxide powders by the BET method". This standard covers: ISO 12800:2017 gives guidelines on the determination of the specific surface area of as-fabricated uranium dioxide powder by volumetric or gravimetric determination of the amount of nitrogen adsorbed on the powder, and can be applied to other similar materials, e.g. U3O8, UO2-PuO2 powders, and other bodies with similar surface areas, e.g. powder granules or green pellets, provided that the conditions described are fulfilled. Modifications using other adsorbing gases are included. The method is relevant as long as the expected value is in the range between 1 m2/g and 10 m2/g.
ISO 12800:2017 gives guidelines on the determination of the specific surface area of as-fabricated uranium dioxide powder by volumetric or gravimetric determination of the amount of nitrogen adsorbed on the powder, and can be applied to other similar materials, e.g. U3O8, UO2-PuO2 powders, and other bodies with similar surface areas, e.g. powder granules or green pellets, provided that the conditions described are fulfilled. Modifications using other adsorbing gases are included. The method is relevant as long as the expected value is in the range between 1 m2/g and 10 m2/g.
ISO 12800 is classified under the following ICS (International Classification for Standards) categories: 27.120.30 - Fissile materials and nuclear fuel technology. The ICS classification helps identify the subject area and facilitates finding related standards.
ISO 12800 has the following relationships with other standards: It is inter standard links to FprEN ISO 12800, ISO 12800:2017. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
ISO 12800 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
FINAL DRAFT
International
Standard
ISO/FDIS 12800
ISO/TC 85/SC 5
Nuclear fuel technology —
Secretariat: BSI
Guidelines on the measurement of
Voting begins on:
the specific surface area of uranium
2026-09-16
dioxide and plutonium dioxide
Voting terminates on:
powders by the BET method
2026-11-11
Technologie du combustible nucléaire — Lignes directrices pour
le mesurage de l'aire massique (surface spécifique) des poudres
d'oxyde d'uranium et de plutonium par la méthode BET
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/CEN PARALLEL PROCESSING LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
ISO/FDIS 12800:2026(en) © ISO 2026
FINAL DRAFT
ISO/FDIS 12800:2026(en)
International
Standard
ISO/FDIS 12800
ISO/TC 85/SC 5
Nuclear fuel technology —
Secretariat: BSI
Guidelines on the measurement of
Voting begins on:
the specific surface area of uranium
dioxide and plutonium dioxide
Voting terminates on:
powders by the BET method
Technologie du combustible nucléaire — Lignes directrices pour
le mesurage de l'aire massique (surface spécifique) des poudres
d'oxyde d'uranium et de plutonium par la méthode BET
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO 2026
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/CEN PARALLEL PROCESSING
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/FDIS 12800:2026(en) © ISO 2026
ii
ISO/FDIS 12800:2026(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
4.1 Summary of the BET method .1
4.2 Isothermal adsorption curves .2
4.3 Conditions and assumptions .2
5 Procedure . 3
5.1 Sample preparation .3
5.1.1 General .3
5.1.2 Uranium dioxide powders .3
5.1.3 Plutonium dioxide powders .3
5.1.4 Mass of sample .3
5.2 Volumetric measurement .3
5.3 Gravimetric measurement .4
5.4 Multipoint and single-point methods .4
5.5 Dynamic method (carrier gas method) .4
5.6 Alternative methods .4
6 Expression of results . 5
6.1 Methods of calculation .5
6.1.1 Multipoint determination .5
6.1.2 Single-point determination .7
6.2 Precision and accuracy .7
7 Test report . 7
Bibliography . 9
iii
ISO/FDIS 12800:2026(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 85, Nuclear energy, nuclear technologies, and
radiological protection, Subcommittee SC 5, Nuclear installations, processes and technologies, in collaboration
with the European Committee for Standardization (CEN) Technical Committee CEN/TC 430, Nuclear energy,
nuclear technologies, and radiological protection, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement) and with IEC/TC 76, Optical radiation safety and laser equipment.
This third edition cancels and replaces the second edition (ISO 12800:2017), which has been technically
revised.
The main changes are as follows:
— table of contents was adaptively revised;
— Figure 1 in 4.2 was replaced;
— new Subclauses 5.1.1 and 5.1.2 were added (headings only, the content was carried forward);
— new Subclauses 5.1.3 and 5.1.4 were added (entirely new text);
— content of 5.2 was partially revised;
— several editorial changes were added.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
FINAL DRAFT International Standard ISO/FDIS 12800:2026(en)
Nuclear fuel technology — Guidelines on the measurement of
the specific surface area of uranium dioxide and plutonium
dioxide powders by the BET method
1 Scope
This document is applicable to nuclear fuel fabrication. It gives guidelines on the determination of the
specific surface area of as-fabricated uranium dioxide and plutonium dioxide powders by volumetric or
gravimetric determination of the amount of nitrogen adsorbed on the powder. For the measurement of other
uranium oxide powders, such as UO and U O , reference is made to the procedure for uranium dioxide. For
3 3 8
the measurement of MOX(UO -PuO ) powders, reference is made to the procedure for plutonium dioxide.
2 2
When conditions described are fulfilled, modifications using other adsorbing gases are included.
2 2
The method is applicable as long as the expected value is in the range from 1 m /g to 10 m /g for uranium
2 2
dioxide powders, in the range from 0.1 m /g to 45 m /g for plutonium dioxide powders.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO/IEC Guide 98-3, Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in
...
ISO/FDIS 12800
ISO/TC 85/SC 5
Secretariat: BSI
Date: 2026-07-10xx
Nuclear fuel technology — Guidelines on the measurement of the
specific surface area of uranium dioxide and plutonium dioxide
powders by the BET method
Technologie du combustible nucléaire — Lignes directrices pour le mesurage de l'aire massique (surface
spécifique) des poudres d'oxyde d'uranium et de plutonium par la méthode BET
FDIS stage
TThihis drs draafftt i is s ssuubbmmiitttteedd ttoo aa ppaarraallellel l vvoottee i inn IISSOO,, CCEEN.N.
ISO/FDIS 12800:2026(en)
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
E-mail: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO/FDIS 12800:2026(en)
Contents
Foreword . iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
4.1 Summary of the BET method . 1
4.2 Isothermal adsorption curves . 1
4.3 Conditions and assumptions . 2
5 Procedure . 3
5.1 Sample preparation . 3
5.2 Volumetric measurement . 3
5.3 Gravimetric measurement . 4
5.4 Multipoint and single-point methods . 4
5.5 Dynamic method (carrier gas method) . 4
5.6 Alternative methods . 4
6 Expression of results . 5
6.1 Methods of calculation . 5
6.2 Precision and accuracy . 8
7 Test report . 8
Bibliography . 9
iii
ISO/FDIS 12800:2026(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of
ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights
in respect thereof. As of the date of publication of this document, ISO had not received notice of (a) patent(s)
which may be required to implement this document. However, implementers are cautioned that this may not
represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 85, Nuclear energy, nuclear technologies, and
radiological protection, Subcommittee SC 5, Nuclear installations, processes and technologies, in collaboration
with the European Committee for Standardization (CEN) Technical Committee CEN/TC 430, Nuclear energy,
nuclear technologies, and radiological protection, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement) and with IEC/TC 76, Optical radiation safety and laser equipment.
This third edition cancels and replaces the second edition (ISO 12800:2017), which has been technically
revised.
The main changes are as follows:
— table of contents was adaptively revised;
— Figure 1 in 4.2 was replaced;
— new Subclauses 5.1.1 and 5.1.2 were added (headings only, the content was carried forward);
— new Subclauses 5.1.3 and 5.1.4 were added (entirely new text);
— content of 5.2 was partially revised;
— several editorial changes were added.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
ISO/FDIS 12800:2026(en)
Nuclear fuel technology — Guidelines on the measurement of the
specific surface area of uranium dioxide and plutonium dioxide
powders by the BET method
1 Scope
This document is applicable to nuclear fuel fabrication. It gives guidelines on the determination of the specific
surface area of as-fabricated uranium dioxide and plutonium dioxide powders by volumetric or gravimetric
determination of the amount of nitrogen adsorbed on the powder. For the measurement of other uranium
oxide powders, such as UO and U O , reference is made to the procedure for uranium dioxide. For the
3 3 8
measurement of MOX(UO -PuO ) powders, reference is made to the procedure for plutonium dioxide. When
2 2
conditions described are fulfilled, modifications using other adsorbing gases are included.
2 2
The method is applicable as long as the expected value is in the range from 1 m /g to 10 m /g for uranium
2 2
dioxide powders, in the range from 0.1 m /g to 45 m /g for plutonium dioxide powders.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO/IEC Guide 98-3, Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in
measurement (GUM:1995)
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at http://www.iso.org/obp
— IEC Electropedia: available at http://www.electropedia.org/
4 Principle
4.1 Summary of the BET method
The BET method is based on the determination of the amount of gas necessary to cover the surface by a
monomolecular layer. This amount is determined from the isothermal adsorption curve of nitrogen (N ) at
[1]
the temperature of liquid nitrogen (77,4 K) according to Reference . The amount of N adsorbed at a given
[2]
pressure is determined by volumetric or gravimetric measurement . In order to remove surface
contamination of the adsorbent, the sample has to be evacuated and heated under appropriate conditions
before the measurement is performed.
4.2 Isothermal adsorption curves
The isothermal adsorption curve describes the relationship between the mass of the adsorbate, m (N ),
A 2
adsorbed per gram of adsorbent (e.g. UO powder) at an equilibrium pressure of p at constant temperature T,
as shown in Formula (1):
𝑚𝑚 = ƒ(𝑝𝑝,𝑇𝑇) (1)
A
ISO/FDIS 12800:2026(en)
Generally, the relative pressure p/p is introduced instead of the absolute pressure p, where p is the
0 0
saturation vapour pressure which is 1,013 × 10 Pa for nitrogen at 77,4 K.
[3]
Most isothermal adsorption curves can be classified according to Reference to be one of the five common
types (see Figure 1).
Materials with pure micropores (with a diameter<2 nm) result in a type 1 adsorption curve. Most frequently,
types 2 and 4 adsorption curves are observed where the adsorption energy of the first layer, E , is much higher
than that of subsequent layers, E . When E ≈ E , type 3 or type 5 adsorption curves result. The BET method
n 1 n
can be applied to type 2 and type 4 cur
...
PROJET FINAL
Norme
internationale
ISO/FDIS 12800
ISO/TC 85/SC 5
Technologie du combustible
Secrétariat: BSI
nucléaire — Lignes directrices pour
Début de vote:
le mesurage de l'aire massique
2026-09-16
(surface spécifique) des poudres
Vote clos le:
d'oxyde d'uranium et de plutonium
2026-11-11
par la méthode BET
Nuclear fuel technology — Guidelines on the measurement of the
specific surface area of uranium dioxide and plutonium dioxide
powders by the BET method
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSERVATIONS,
NOTIFICATION DES DROITS DE PROPRIÉTÉ DONT ILS
AURAIENT ÉVENTUELLEMENT CONNAISSANCE ET À
FOURNIR UNE DOCUMENTATION EXPLICATIVE.
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
INDUSTRIELLES, TECHNOLOGIQUES ET COM-MERCIALES,
AINSI QUE DU POINT DE VUE DES UTILISATEURS, LES
PROJETS DE NORMES
TRAITEMENT PARALLÈLE ISO/CEN
INTERNATIONALES DOIVENT PARFOIS ÊTRE CONSIDÉRÉS
DU POINT DE VUE DE LEUR POSSI BILITÉ DE DEVENIR DES
NORMES POUVANT
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTATION
NATIONALE.
Numéro de référence
ISO/FDIS 12800:2026(fr) © ISO 2026
PROJET FINAL
ISO/FDIS 12800:2026(fr)
Norme
internationale
ISO/FDIS 12800
ISO/TC 85/SC 5
Technologie du combustible
Secrétariat: BSI
nucléaire — Lignes directrices pour
Début de vote:
le mesurage de l'aire massique
2026-09-16
(surface spécifique) des poudres
Vote clos le:
d'oxyde d'uranium et de plutonium
2026-11-11
par la méthode BET
Nuclear fuel technology — Guidelines on the measurement of the
specific surface area of uranium dioxide and plutonium dioxide
powders by the BET method
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2026
LES DESTINATAIRES DU PRÉSENT PROJET SONT
Tous droits réservés.
INVITÉS À PRÉSENTER, AVEC LEURS OBSERVATIONS,
NOTIFICATION DES DROITS DE PROPRIÉTÉ DONT ILS
La présente publication de l’ISO est protégée par le droit d’auteur et demeure la propriété de l’ISO et/ou de ses concédants de
AURAIENT ÉVENTUELLEMENT CONNAISSANCE ET À
licence.
FOURNIR UNE DOCUMENTATION EXPLICATIVE.
Le contenu de la présente publication de l’ISO est fourni sous licence, et n’est pas vendu. Son utilisation est soumise aux conditions
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
de licence applicables définies par l’ISO, un organisme membre de l’ISO, ou un distributeur tiers agréé.
INDUSTRIELLES, TECHNOLOGIQUES ET COM-MERCIALES,
Sous réserve des besoins liés à sa mise en œuvre ou d’une autorisation expresse prévue aux termes d’une licence distincte, aucune
AINSI QUE DU POINT DE VUE DES UTILISATEURS, LES
partie de la présente publication de l’ISO ne peut être reproduite, distribuée, modifiée, utilisée ou mise à disposition sous quelque PROJETS DE NORMES
TRAITEMENT PARALLÈLE ISO/CEN
INTERNATIONALES DOIVENT PARFOIS ÊTRE CONSIDÉRÉS
forme ou par quelque moyen que ce soit – électronique ou mécanique, y compris la photocopie, la numérisation, l’enregistrement
DU POINT DE VUE DE LEUR POSSI BILITÉ DE DEVENIR DES
ou la publication sur des plateformes numériques internes ou externes.
NORMES POUVANT
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTATION
Toute utilisation hors du champ d’application des droits accordés est interdite et peut donner lieu à des poursuites judiciaires.
NATIONALE.
ISO copyright office
Case postale 401 • CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
Numéro de référence
ISO/FDIS 12800:2026(fr) © ISO 2026
ii
ISO/FDIS 12800:2026(fr)
Sommaire Page
Avant-propos .iv
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Principe. 1
4.1 Description de la méthode BET .1
4.2 Courbes isothermes d'adsorption .2
4.3 Conditions requises .2
5 Procédure . 3
5.1 Préparation de l'échantillon .3
5.1.1 Généralités .3
5.1.2 Poudres de dioxyde d'uranium .3
5.1.3 Poudres de dioxyde de plutonium.3
5.1.4 Masse d'échantillon .3
5.2 Méthode de mesure volumétrique .4
5.3 Méthode de mesure gravimétrique.4
5.4 Méthode multipoints et méthode dite “à point unique” .4
5.5 Méthode dynamique du gaz vecteur .4
5.6 Méthodes alternatives .4
6 Expression des résultats . 5
6.1 Méthodes de calcul . .5
6.1.1 Détermination multipoints .5
6.1.2 Détermination en un point .7
6.2 Fidélité et exactitude . .7
7 Rapport d'essai . 7
Bibliographie . 8
iii
ISO/FDIS 12800:2026(fr)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux
de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général
confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a
été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir
www.iso.org/directives).
L'ISO attire l'attention sur le fait que la mise en application du présent document peut entraîner l'utilisation
d'un ou de plusieurs brevets. L'ISO ne prend pas position quant à la preuve, à la validité et à l'applicabilité
de tout droit de propriété revendiqué à cet égard. À la date de publication du présent document, l'ISO
n'avait pas reçu notification qu'un ou plusieurs brevets pouvaient être nécessaires à sa mise en application.
Toutefois, il y a lieu d'avertir les responsables de la mise en application du présent document que des
informations plus récentes sont susceptibles de figurer dans la base de données de brevets, disponible à
l'adresse www.iso.org/brevets. L'ISO ne saurait être tenue pour responsable de ne pas avoir identifié tout ou
partie de tels droits de brevet.
Les appellations commerciales éventuellement mentionnées dans le présent document sont données pour
information, par souci de commodité, à l'intention des utilisateurs et ne sauraient constituer un engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion de
l'ISO aux principes de l'Organisation mondiale du commerce (OMC) concernant les obstacles techniques au
commerce (OTC), voir www.iso.org/avant-propos.
Le présent document a été élaboré par le comité technique ISO/TC 85, Énergie nucléaire, technologies
nucléaires, et radioprotection, Sous-comité SC 5, Installations nucléaires, procédés et technologies, en
collaboration avec le comité technique du Comité européen de normalisation (CEN) CEN/TC 430, Énergie
nucléaire, technologies nucléaires, et radioprotection, conformément à l'accord de coopération technique entre
l'ISO et le CEN (Accord de Vienne) et avec l'IEC/TC 76, Sécurité des rayonnements optiques et matériels laser.
Cette troisième édition annule et remplace la deuxième édition (ISO 12800:2017), qui a fait l'objet d'une
révision technique.
Les principales modifications sont les suivantes:
— la table des matières a été révisée de manière adaptative;
— la Figure 1 au paragraphe 4.2 a été remplacée;
— les nouveaux paragraphes 5.1.1 et 5.1.2 ont été ajoutés (titres uniquement, le contenu a été reporté);
— les nouveaux paragraphes 5.1.3 et 5.1.4 ont été ajoutés (texte entièrement nouveau);
— le contenu du paragraphe 5.2 a été partiellement révisé;
— plusieurs modifications rédactionnelles ont été ajoutées.
Il convient que l'utilisateur adresse tout retour d'information ou toute question concernant le présent
document à l'organisme national de normalisation de son pays. Une liste exhaustive desdits organismes se
trouve à l'adresse www.iso.org/fr/members.html.
iv
PROJET FINAL Norme internationale ISO/FDIS 12800:2026(fr)
Technologie du combustible nucléaire — Lignes directrices
pour le mesurage de l'aire massique (surface spécifique) des
poudres d'oxyde d'uranium et de plutonium par la méthode
BET
1 Domaine d'application
Le présent document est applicable à la fabrication de combustible nucléaire. Il fournit des lignes directrices
relatives à la détermination de l'aire massique (surface spécifique) des poudres de dioxyde d'uranium et
de dioxyde de plutonium telles qu'elles sont fabriquées, par détermination volumétrique ou gravimétrique
de la quantité d'azote adsorbée sur la poudre. Pour la mesure d'autres poudres d'oxyde d'uranium, tel que
l'UO et l'U O , il est fait référence à la procédure relative au dioxyde d'uranium. Pour la mesure des poudres
3 3 8
MOX (UO -PuO ), il est fait référence à la procédure relative au dioxyde de plutonium. Lorsque les conditions
2 2
décrites sont remplies, des modifications utilisant d'autres gaz adsorbants sont incluses.
2 2
La méthode est applicable tant que la valeur attendue se situe dans la plage de 1 m /g à 10 m /g pour les
2 2
poudres de dioxyde d'uranium, dans la plage de 0,1 m /g à 45 m /g pour les poudres de dioxyde de plutonium.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu'ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l'édition citée s'applique. Pour
les références non datées, la dernière édition du document de référence s'applique (y compris les éventuels
amendements).
Guide ISO/IEC 98-3, Incertitude de mesure — Partie 3: Guide
...











