ISO 2795:2014
(Main)Plain bearings — Sintered bushes — Dimensions and tolerances
Plain bearings — Sintered bushes — Dimensions and tolerances
ISO 2795:2014 specifies the dimensions and tolerances applicable to sintered bearings for the following ranges of inside diameters: cylindrical bearings: 1 mm to 60 mm; flanged bearings: 1 mm to 60 mm; spherical bearings: 1 mm to 20 mm.
Paliers lisses — Coussinets frittés — Dimensions et tolérances
Drsni ležaji - Sintrane puše - Mere in tolerance
Ta mednarodni standard določa mere in tolerance, ki se uporabljajo za sintrane ležaje za
naslednje obsege notranjih premerov:
– valjasti ležaji: 1 mm do 60 mm;
– ležaji s prirobnico: 1 mm do 60 mm;
– kroglični ležaji: 1 mm do 20 mm.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST ISO 2795:2015
01-marec-2015
1DGRPHãþD
SIST ISO 2795:1995
Drsni ležaji - Sintrane puše - Mere in tolerance
Plain bearings - Sintered bushes - Dimensions and tolerances
Paliers lisses - Coussinets frittés - Dimensions et tolérances
Ta slovenski standard je istoveten z: ISO 2795:2014
ICS:
21.100.10 Drsni ležaji Plain bearings
SIST ISO 2795:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 2795:2015
---------------------- Page: 2 ----------------------
SIST ISO 2795:2015
INTERNATIONAL ISO
STANDARD 2795
Fifth edition
2014-01-15
Plain bearings — Sintered bushes —
Dimensions and tolerances
Paliers lisses — Coussinets frittés — Dimensions et tolérances
Reference number
ISO 2795:2014(E)
©
ISO 2014
---------------------- Page: 3 ----------------------
SIST ISO 2795:2015
ISO 2795:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 2795:2015
ISO 2795:2014(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative reference . 1
3 Material . 1
4 Cylindrical bearings . 1
4.1 Dimensions . 1
4.2 Tolerances . 3
5 Flanged bearings . 4
5.1 Dimensions . 4
5.2 Tolerances . 6
6 Spherical bearings . 7
6.1 Dimensions . 7
6.2 Tolerances . 7
Bibliography . 9
© ISO 2014 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 2795:2015
ISO 2795:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received. www.iso.org/patents.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
The committee responsible for this document is ISO/TC 123, Plain bearings, Subcommittee SC 7, Special
types of plain bearings.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the WTO principles in the Technical Barriers to Trade
(TBT) see the following URL: http://www.iso.org/iso/home/standards_development/resources-for-
technical-work/foreword.htm
This fifth edition cancels and replaces the fourth edition (ISO 2795:1991), of which it constitutes a minor
revision.
iv © ISO 2014 – All rights reserved
---------------------- Page: 6 ----------------------
SIST ISO 2795:2015
ISO 2795:2014(E)
Introduction
The sizes given in this International Standard are based on a range of shaft diameters which are
considered to correspond to the requirements of industry. For all except the smallest sizes, a thin-wall
series is provided in addition to the normal series in order to introduce an element of choice and, more
importantly, to provide for the possibility of the same sizes being adopted for plain bearings made from
other materials.
It is envisaged that as far as possible, the same outsi
...
INTERNATIONAL ISO
STANDARD 2795
Fifth edition
2014-01-15
Plain bearings — Sintered bushes —
Dimensions and tolerances
Paliers lisses — Coussinets frittés — Dimensions et tolérances
Reference number
ISO 2795:2014(E)
©
ISO 2014
---------------------- Page: 1 ----------------------
ISO 2795:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 2795:2014(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative reference . 1
3 Material . 1
4 Cylindrical bearings . 1
4.1 Dimensions . 1
4.2 Tolerances . 3
5 Flanged bearings . 4
5.1 Dimensions . 4
5.2 Tolerances . 6
6 Spherical bearings . 7
6.1 Dimensions . 7
6.2 Tolerances . 7
Bibliography . 9
© ISO 2014 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 2795:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received. www.iso.org/patents.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
The committee responsible for this document is ISO/TC 123, Plain bearings, Subcommittee SC 7, Special
types of plain bearings.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the WTO principles in the Technical Barriers to Trade
(TBT) see the following URL: http://www.iso.org/iso/home/standards_development/resources-for-
technical-work/foreword.htm
This fifth edition cancels and replaces the fourth edition (ISO 2795:1991), of which it constitutes a minor
revision.
iv © ISO 2014 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 2795:2014(E)
Introduction
The sizes given in this International Standard are based on a range of shaft diameters which are
considered to correspond to the requirements of industry. For all except the smallest sizes, a thin-wall
series is provided in addition to the normal series in order to introduce an element of choice and, more
importantly, to provide for the possibility of the same sizes being adopted for plain bearings made from
other materials.
It is envisaged that as far as possible, the same outside diameters will be recommended for all types of
plain bearings.
© ISO 2014 – All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 2795:2014(E)
Plain bearings — Sintered bushes — Dimensions and
tolerances
1 Scope
This International Standard
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.