ISO 11999-6:2016
(Main)PPE for firefighters — Test methods and requirements for PPE used by firefighters who are at risk of exposure to high levels of heat and/or flame while fighting fires occurring in structures — Part 6: Footwear
PPE for firefighters — Test methods and requirements for PPE used by firefighters who are at risk of exposure to high levels of heat and/or flame while fighting fires occurring in structures — Part 6: Footwear
ISO 11999-6:2016 specifies the minimum design and performance requirements for footwear as part of personal protective equipment [PPE] to be used by firefighters, primarily but not solely to protect against flame and high thermal loads while fighting fires occurring in structures.
Équipement de protection personnelle pour pompiers — Méthodes d'essai et exigences pour les équipements de protection personnelle utilisés par les pompiers qui sont à risque d'une exposition à des niveaux élevés de chaleur et/ou de flamme quand la lutte contre les incendies survient dans les structures — Partie 6: Chaussures
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 11999-6
First edition
2016-08-01
PPE for firefighters — Test methods
and requirements for PPE used
by firefighters who are at risk of
exposure to high levels of heat and/or
flame while fighting fires occurring in
structures —
Part 6:
Footwear
Équipement de protection personnelle pour pompiers — Méthodes
d’essai et exigences pour les équipements de protection personnelle
utilisés par les pompiers qui sont à risque d’une exposition à des
niveaux élevés de chaleur et/ou de flamme quand la lutte contre les
incendies survient dans les structures —
Partie 6: Chaussures
Reference number
©
ISO 2016
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification, design and performance level . 1
4.1 Classification . 1
4.2 Design . 2
4.3 Performance Level . 2
5 Sampling and conditioning . 3
5.1 Sampling . 3
5.2 Conditioning . 3
6 Requirements . 3
6.1 General requirement . 3
6.2 Thermal behaviour . 7
6.2.1 Insulation against heat . 7
6.2.2 Radiant heat . 7
6.2.3 Flame resistance . 7
6.3 Resistance to chemicals . 7
6.3.1 Degradation resistance . . 7
6.3.2 Permeation resistance . 8
6.4 Electrical Properties . 8
6.4.1 General. 8
6.4.2 Electrically insulating footwear . 8
6.4.3 Antistatic footwear . 9
6.5 Water resistance . 9
6.6 Outsole . 9
6.6.1 Cleat design . 9
6.6.2 Cleat height . 9
6.6.3 Cleat height in the waist area . 9
6.6.4 Heel breast . 9
6.7 Zipper (slide fastener) .10
6.7.1 Zipper construction .10
6.7.2 Zipper puller attachment strength .10
6.7.3 Zipper lateral strength .10
7 Test methods .10
7.1 Insulation against heat .10
7.2 Radiant heat .10
7.3 Flame resistance test .11
7.3.1 Conditioning and sampling .11
7.3.2 Procedure .11
7.4 Zipper .12
7.4.1 Puller attachment strength .12
7.4.2 Lateral strength . .12
8 Marking .13
9 Information to be supplied .15
9.1 General .15
9.2 Antistatic footwear .15
9.3 Electrically insulating footwear .16
9.4 Insocks .16
9.5 Information regarding penetration resistant insert .17
Annex A (normative) Assessment of the footwear by the laboratory during testing for
resistance to heat and flame .18
Annex B (informative) Assessment of the footwear by the wearer .20
Annex C (informative) Assessment of the performance of the footwear .21
Annex D (informative) Summary of testing methodology used in 6.3 .22
Annex E (informative) Slip resistance .25
Bibliography .28
iv © ISO 2016 – All rights reserved
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 94, Personal safety — Protective clothing and
equipment, Subcommittee SC 14, Firefighters’ personal equipment.
ISO 11999 consists of the following parts, under the general title PPE for firefighters — Test methods and
requirements for PPE used by firefighters who are at risk of exposure to high levels of heat and/or flame
while fighting fires occurring in structures:
— Part 1: General
— Part 2: Compatibility [Technical Specification]
— Part 3: Clothing
— Part 4: Gloves
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.