ISO 17754:2014
(Main)Timber structures — Test methods — Torsional resistance of driving in screws
Timber structures — Test methods — Torsional resistance of driving in screws
ISO 17754:2014 specifies a test method to determine the torsional resistance to driving of screws in solid timber or glued laminated timber or other wood-based materials. The method is used primarily to ensure the torque that may be applied to install screws will be less than the specified failure torque of the screw.
Structures en bois — Méthodes d'essai — Résistance à la torsion des vis lors du vissage
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 17754
First edition
2014-05-01
Timber structures — Test methods
— Torsional resistance of driving in
screws
Structures en bois — Méthodes d’essai — Résistance à la torsion des
vis lors du vissage
Reference number
©
ISO 2014
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 1
5 Material requirements . 1
5.1 Description . 1
6 Test methods . 2
6.1 General . 2
6.2 Conditioning . 2
6.3 Sampling . 2
6.4 Test piece dimensions . 2
7 Test . 3
7.1 Test setup . 3
7.2 Procedure . 3
7.3 Results . 4
8 Test report . 4
8.1 Test piece . 4
8.2 Test method . 5
8.3 Test results. 5
Bibliography . 6
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 165, Structural Timber.
iv © ISO 2014 – All rights reserved
INTERNATIONAL STANDARD ISO 17754:2014(E)
Timber structures — Test methods — Torsional resistance
of driving in screws
1 Scope
This I
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.